Lutron Electronics Energi Savr Node QS DALI Manuale utente

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Ratings

Input: 220 - 240 V 50/60 Hz 100 mA

Output: 16 V 250 mA per DALI bus

Operating environment: 0 ˚C - 40 ˚C

Maximum humidity: 90% non-condensing

Thermal dissipation: 35 BTU/hr

Calibration point maximum: 75 ˚C

QS link: 24 V , 3 QS keypads

Model number overview

Energi Savr Node QSNE-2DAL-D

Energi Savr Node QS: Digital xture controller

2: 2 DALI Buses

DAL: DALI

D: DIN rail compatible

Lutron®|1

Caution: please read this guide before installing.

Contents Page

Ratings and model number overview

Product overview

Wiring overview

Mounting

Mains voltage wiring

DALI bus wiring

Sensor wiring

Application overview

QS link wiring

Programming connections

Testing and troubleshooting

Warranty

Contact information

System Example

Energi Savr

Node QS

Energi Savr

Node QS

Ballast

seeTouch®QS

Wallstation

Ballast

Quantum

Panel

LUTRON

Contact

Closure

Interface GRAFIK

Eye QS

Up to 64

ballasts on

each bus

QS Control Link

DALI Bus 1

DALI Bus 2

IR Sensor

Daylight Sensor

Occupancy Sensor

Up to 100

total QS

devices

Ethernet Programming Link

One sensor group

shown; connections

available for up to four

sensor groups.

220-240 V

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Product overview

WARNING! Danger of Shock. May result in serious injury or death. DO NOT WIRE

WHEN LIVE! Switch off power via circuit breaker or isolator before wiring or servicing

the Energi Savr Node QS.

Buttons and LEDs on the front of the unit are used for programming and troubleshooting.

If wiring is exposed when accessing buttons and LEDs, the unit must be accessed by a

certied electrician, following local codes.

The DALI Energi Savr Node QS powers two DALI buses and supports communication for a

maximum of 64 DALI ballasts or other controllable illumination drivers per link, 128 total. An

Energi Savr Node QS system consists of an Energi Savr Node QS, ballasts, sensors, keypads,

and QS interface devices. The diagram on the previous pages shows a typical system topology.

· All ballasts and Energi Savr Node QS units are powered by mains voltage (Live and Neutral).

· Two additional wires for digital communication per DALI bus (DA1/DA1 DA2/DA2).

· The DALI bus may be treated as mains voltage and thus may be run within the same conduit.

· The DALI bus wires are non-polarised and can be run as a daisy chain, T-tap, star, or in any

combination.

· Only one Energi Savr Node QS or DALI Bus Supply may be connected per DALI bus.

· The Energi Savr Node QS is limited to:

· 128 total ballasts. (64 per DALI bus)

· 4 daylight sensors

· 4 occupancy sensors

· 4 IR sensors

· The QS Link can have up to 100 zones and 100 devices.

· The Energi Savr Node QS occupies 1 device position and up to 32 zone positions.

· In a system with multiple Energi Savr Node QS units, a maximum of 100 daylight sensors

and 100 occupancy sensors are permitted.

Refer to the following step-by-step guide for proper Energi Savr Node QS installation.

Lutron®|2

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Mains

Wiring

Link

Programming

Jack

DALI 1

DA1/DA1

DALI 2

DA2/DA2

Sensors

PELV

Wiring overview

Lutron®|3

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr Node

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Lutron®|4

Step-by-step installation instructions

Step 1: Mounting the Energi Savr Node QS

Note: Mount the Energi Savr Node QS in a position

where it can be easily located and accessed if service

or troubleshooting is necessary. The Energi Savr Node

QS should be mounted with the directional arrows

pointing upwards.

Use an IP65 rated consumer panel or breaker panel

with integrated DIN rail and dead cover. The Energi

Savr Node QS is 161,7 mm wide.

To clip the Energi Savr Node QS onto the DIN rail:

1. Hook the Energi Savr Node QS onto the top of the

DIN rail

2. Pivot the Energi Savr Node QS onto the DIN rail

3. Press until the Energi Savr Node QS clips lock

To remove the Energi Savr Node QS from the DIN rail:

1. Using a screwdriver, pull the orange clips until they

click in the unlocked position.

2. Reverse the steps above.

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr NodeTM QS

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Step 2: Mains voltage wiring

The Energi Savr Node QS operates at 220-240 V .

Use the following instructions to wire line voltage to the

Energi Savr Node QS.

WARNING! Danger of Shock. May result in

serious injury or death. DO NOT WIRE WHEN

LIVE! Switch off power via circuit breaker or

isolator before wiring or servicing the Energi

Savr Node QS.

Buttons and LEDs on the front of the unit are used

for programming and troubleshooting. If wiring is

exposed when accessing buttons and LEDs, the

unit must be accessed by a certied electrician,

following local codes.

1. Use 1,0 mm2to 4,0 mm2conductors (depending on

breaker rating) to feed the mains wiring. The device

draws less than 100 mA.

Strip 8 mm of insulation off the line voltage/mains cables.

3. Wire the mains to the terminals labelled L, N, and G.

A three-position terminal block is provided. Do not wire

mains wires to the earth terminal.

4. The recommended installation torque is 0,5 N·m

4. The Energi Savr Node QS is earthed through the G

terminal. Attach the earth wire.

5. Turn on the circuit breaker or isolator to power up the

Energi Savr Node QS. The POWER indicator on the

Energi Savr Node QS will display a green light continu-

ously when properly powerd up. If the indicator does

not light, turn off power, then check the line voltage

wiring.

6. Turn power off.

Note: If additional wiring space is required, the Energi

Savr Node QS can be removed from the DIN rail while

wiring. Follow the instructions from step 1 for details.

Lutron®|5

L N G

These

terminals

1,0 - 4,0 mm2

conductors

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr NodeTM QS

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Step 3: DALI bus wiring

DALI bus wiring may be considered to be mains

voltage. (It is not considered SELV.) Consult applicable

national and local codes for compliance.

Lutron recommends using two different colours for

DA1 and DA2. This will prevent wiring mistakes where

several bus wires are co-located. Use the following

instructions for wiring the DALI bus.

WARNING! Danger of Shock. May result in

serious injury or death. DO NOT WIRE WHEN

LIVE! Switch off power via circuit breaker or

isolator before wiring or servicing the Energi

Savr Node QS.

Buttons and LEDs on the front of the unit are used

for programming and troubleshooting. If wiring is

exposed when accessing buttons and LEDs, the

unit must be accessed by a certied electrician,

following local codes.

1. Wire the DALI bus from the DALI terminals to all ballasts.

2. Turn on the circuit breaker or isolator to power up. The

POWER indicator lights green when powered up.

3. The Energi Savr Node QS outputs DALI compliant volt-

age levels (16 V +/-4,5 V ). Use a voltage meter

to conrm this voltage.

4. Turn power off.

Lutron®|6

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr NodeTM QS

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

DALI 1

DALI 2

DALI Bus 1 DALI Bus 2

These terminals accept

1,0 - 4,0 mm2

conductors

Wire gauge Maximum DALI-compliant

bus wire length

4,0 mm2(12 AWG) 671 m (2 200 ft)

2,5 mm2(14 AWG) 427 m (1 400 ft)

1,5 mm2(16 AWG) 275 m (900 ft)

1,0 mm2(18 AWG) 175 m (570 ft)

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr NodeTM QS

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

Step 4: Sensor wiring

To connect a daylight sensor, occupancy sensor and/or infrared receiver, refer to the instruction sheets provided with the

devices. Diagrams for the PELV sensors terminals are shown below.

WARNING! Danger of Shock. May result in serious injury or death. DO NOT WIRE WHEN LIVE! Switch off

power via circuit breaker or isolator before wiring or servicing the Energi Savr Node QS.

Buttons and LEDs on the front of the unit are used for programming and troubleshooting. If wiring is exposed

when accessing buttons and LEDs, the unit must be accessed by a certied electrician, following local codes.

Note: The Energi Savr Node QS accepts only one infrared input (either daylight or IR sensor) per group.

Lutron®|7

NOTE: There

are four sensor

groups. Each

group is wired in

the same way and

is shown above.

20 V

IR Sensor

Daylight Sensor

Occupancy Sensor

COM

LUTRON

Occupancy SensorDaylight Sensor

* Do not connect white wire if using an IR sensor.

IR Sensor

LUTRON

Red

Black

Yellow

OCC

COM

+20 V

Red

Black

White

White *

D E

Test

Power

Temp

QS Ethernet DALI 1 DALI 2

Photo

Com

24V

Com

Occ

Photo

Occ

Versaplex QSTM

VQS-2D-PD-M

www.lutron.com

+44.(0)20.7680.4481

D E

Test

Temp

QS DALI 1 DALI 2

Versaplex QSTM

VQS-2D-PD-M

LUTRON

1 1

3 3 4 4

2 2

www.lutron.com

+44.(0)20.7680.4481

Sensor Group 1

Sensor Group 3

Sensor Group 2

Sensor Group 4

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Lutron®|8

Simple applications: precongured modes require no commissioning

Occupancy

Sensor

Occupancy

Sensor

Loop 2

Wired to

sensor

group 2

Bus 1

Perimeter Interior

Window Window

Energi Savr

Node QS

Wired to

sensor

group 1

Occupancy

Sensor

Daylight

Sensor

Bus 2

Bus 1

Perimeter Interior

Window Window

Energi Savr

Node QS

LUTRON

Wired to

sensor

group 4

Preconﬁgured mode 2

Two zones with occupancy sensors

* Six ﬁxtures shown on each bus. However, up to 64

ﬁxtures can be connected per bus.

Preconﬁgured mode 1

Perimeter daylighting

* Four ﬁxtures shown on bus 1 and eight ﬁxtures

shown on bus 2, however, up to 64 ﬁxtures can be

connected per bus.

Occupancy sensor Daylight sensor

Connected to sensor group 1 Controls bus 1 only Controls bus 1 only

Connected to sensor group 2 Controls bus 2 only Controls bus 2 only

Connected to sensor group 3 Controls both buses Controls both buses with equal daylight gain

Connected to sensor group 4 Controls both buses Controls both buses with lower daylight gain on bus 2

Default Behavior for Sensor Connections

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

D E

Test

Power

Hi Temp

Ethernet DALI 1 DALI 2

Photo

Com

20 V

Com

MUX

24 V

COM

Occ

Photo

Occ

Energi Savr NodeTM QS

QSNE-2DAL-D

230 V~ 50/60 Hz 100 mA

www.lutron.com

+44.(0)20.7680.4481

L N

1 1 2 2

33 4 4

8 mm

0,5 N∙m

N1771

Z096

Lutron®|9

Step 5: QS link wiring

WARNING! Danger of Shock. May result in

serious injury or death. DO NOT WIRE WHEN

LIVE! Switch off power via circuit breaker or

isolator before wiring or servicing the Energi

Savr Node QS.

Buttons and LEDs on the front of the unit are used

for programming and troubleshooting. If wiring is

exposed when accessing buttons and LEDs, the

unit must be accessed by a certied electrician,

following local codes.

QS system communications uses PELV low-voltage

wiring. Follow all local and national electrical codes

when installing PELV wiring with line voltage/mains

wiring.

Each terminal accepts up to two 1,0 mm2wires. The

total length of the control link must not exceed 600 m.

Use twisted/shielded pair of 1,0 mm2wire for data link.

Cable is available from Lutron, P/N GRX-CBL-346S.

Check for compatibility in your area.

A QS system can have up to 100 zones and 100

devices. The Energi Savr Node QS occupies 1 device

position and up to 32 zone positions.

See diagram on the right for QS link wiring.

1. Connect terminals 1, 3 and 4 to all Energi Savr Node

QS units.

2. Each Energi Savr Node QS has its own power supply.

3. Terminate the terminal 2 connection (24 V ) so that

each control unit supplies power to a maximum of

three QS keypads. Each QS keypad should receive

power from only one Energi Savr Node QS.

(see diagram on page 11)

NOTE: To connect extra keypads, use a separate power

supply (24 V), and only connect COM, MUX, MUX to the

keypads connected to the Energi Savr Node QS.

COM

24 V

MUX

Energi Savr NodeTM QS DALI Installation Guide

Energi Savr Node QSTM DALI | Installation Guide

Lutron®|10

Energi Savr

Node QS

Sivoia®QS

Shade

Sivoia®QS

Smart Power

Panel

seeTouch®QS Keypads

QS Control Link

Sivoia®QS

Smart Power

Panel

Sivoia®QS

Shade

seeTouch®QS Keypads

Energi Savr

Node QS

QS Control Link

QS link wiring (continued)

Daisy-Chain Wiring Example

T-Tap Wiring Example

Indice

Lingue:

Altri manuali Lutron Electronics Sistema di controllo

Lutron Electronics

Lutron Electronics PJ2-3BRL Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuale utente

Lutron Electronics

Lutron Electronics AuroRa Manuale utente

Lutron Electronics

Lutron Electronics RadioRA-SR Manuale utente

Lutron Electronics

Lutron Electronics Grafik Eye Manuale utente

Lutron Electronics

Lutron Electronics homeworks qs Manuale utente

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics RadioRA Manuale utente

Lutron Electronics

Lutron Electronics myRoom Manuale utente

Lutron Electronics

Lutron Electronics RadioRA Istruzioni per il montaggio

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QSG-3PCE Istruzioni operative

Lutron Electronics

Lutron Electronics Architrave GRAFIK5000 Manuale utente

Lutron Electronics

Lutron Electronics Grafik Eye GRX-CCO-8 Manuale utente

Lutron Electronics

Lutron Electronics VISEO GRAFIK5000 Manuale utente

Lutron Electronics

Lutron Electronics LCP128 Manuale utente

Lutron Electronics

Lutron Electronics RRD-6CL-WH Manuale utente

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics Pico PJL-2B Manuale utente

Lutron Electronics

Lutron Electronics Stanza Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente