Lutron Electronics Homeworks qs Manuale utente

HomeWorks QS Installation Checklist

This checklist is intended to provide reminders before the installation process begins, as well as when it

is complete.

Panel Link

Daisy chain the Module Interfaces (MIs) on each Panel Link

The MIs must be wired in a daisy chain configuration on the link. The maximum wire run length is

1,000ft using 18/22 wire (twisted and shielded).

Terminate the MI link

The MI link must be terminated at the last MI using an LT-1 link terminator (provided in the

processor box) if the link runs farther than 50 feet. A 120-ohm resistor may be used across terminals

3 and 4 if an LT-1 isn't available.

Terminal 2 is unused for MIs

Do not connect terminal 2 between external MIs and the Processor. All external MIs have their own

integral power supply and do not need to be powered from the Processor.

Install 4R and 4M modules in the bottom locations of a remote power panel

This is the optimum configuration for heat dissipation, but it is not necessary.

Remove bypass jumpers

Remove the bypass jumpers from the RPM terminal blocks after verifying the system high-voltage

wiring.

MI and RPM Addresses

Make sure that the dial switches on the MI and each RPM matches the appropriate address: 1

through 8 for RPMs and 0 through F for MIs.

Manual Override Switch

Wire manual override switch(s) to each MI.

QS Wired Link

Terminal 2 is unused for the GRAFIK Eye QS and Wallbox Power Module Units

Do not connect terminal 2 between GRAFIK Eye QS and/or Wallbox Power Module units and the

Processor. All GRAFIK Eye QS and Wallbox Power Module units have their own internal power

supply, connected to line voltage in the backbox, and do not need to be powered from the

Processor.

Connect the Keypads

Wire the Keypad link using any of the following wiring topologies: daisy chain, star, or t-

tap. Termination is not required on the keypad link. Ensure QS power supplies are wired according

to the instructions and do not exceed the PDU rating of the power supply.

RF Link

First Hybrid Repeater on the Link

The first Hybrid Repeater on the link must be hard-wired back to the physical link on the Processor.

The wire run can be up to 1000ft using Lutron’s 4 conductor cable and the Hybrid Repeater can be

wired to pin 2 and draw its 3 PDUs from the din-rail power supply feeding the Processor.

30/60 Rule

When using multiple Hybrid Repeaters on a single link, the first one must be physically wired to the

Processor link and the others are typically then wirelessly connected for range extension. Hybrid

Repeaters should be placed no more than 60ft apart. All wireless devices communicating on the link

are then to be placed within 30ft of a Hybrid Repeater on that specific link.

H48 Link

Daisy chain the H48 Interfaces on each H48 Link

The H48 link must be wired in a daisy chain configuration. The maximum wire run length is 1,000ft

using 18/22 wire (twisted and shielded).

Terminate the H48 link

The H48 link must be terminated at the processor and at the last H48 using an LT-1 link terminator

(provided in the processor box) if the link runs farther than 50 feet. A 120-ohm resistor may be used

across terminals 3 and 4 if an LT-1 isn't available.

Link Translator

H48 Links that require termination also require an HQ-HWI-LX Link Translator.

Terminal 2 is unused for H48 Interfaces

Do not connect terminal 2 between H48 Interfaces and the Processor. All H48s use the power supply

provided in the HWI-LV17 and do not need to be powered from the Processor.

Processor

Connect Ethernet wiring to each processor

Every HomeWorks QS processor must be wired to the same local area network. Ethernet is required

for inter-processor communication and for 3rd party integration.

Legacy Devices

Terminal 2 is unused for Q96 Interfaces

Do not connect terminal 2 between Q96 Interfaces and the Processor. All Q96s get powered from

the QED shade power supply and do not need to be powered from the Processor.

Terminal 2 is unused for HWI Keypads

HWI Wired keypads require 15V DC power (do not use 24V DC from link)

Altri manuali per homeworks qs

Indice

Altri manuali Lutron Electronics Sistema di controllo

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics Grafik Eye GRX-CCO-8 Manuale utente

Lutron Electronics

Lutron Electronics RadioRA Manuale utente

Lutron Electronics

Lutron Electronics VISEO GRAFIK5000 Manuale utente

Lutron Electronics

Lutron Electronics RadioRA-SR Manuale utente

Lutron Electronics

Lutron Electronics AuroRa Manuale utente

Lutron Electronics

Lutron Electronics Energi Savr Node QS DALI Manuale utente

Lutron Electronics

Lutron Electronics myRoom Manuale utente

Lutron Electronics

Lutron Electronics LCP128 Manuale utente

Lutron Electronics

Lutron Electronics PJ2-3BRL Manuale utente

Lutron Electronics

Lutron Electronics Pico PJL-2B Manuale utente

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics Stanza Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QSG-3PCE Istruzioni operative

Lutron Electronics

Lutron Electronics RadioRA 2 Manuale utente

Lutron Electronics

Lutron Electronics Architrave GRAFIK5000 Manuale utente

Lutron Electronics

Lutron Electronics Grafik Eye Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuale utente

Lutron Electronics

Lutron Electronics RadioRA Istruzioni per il montaggio

Lutron Electronics

Lutron Electronics RRD-6CL-WH Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente

Lutron Electronics homeworks qs Manuale utente

Manuali Sistema di controllo popolari di altre marche