Marshall Amplification DSL40CR Manuale utente

DSL40CR

DSL100HR

QUICK START GUIDE

CONGRATULATIONS ON PURCHASING YOUR

MARSHALL 1DSL.

Download the full manual at www.marshall.com

FÉLICITATIONS POUR L’ACHAT DE VOTRE

AMPLIFICATEUR DSL.

Téléchargez le manuel complet sur

www.marshall.com

HERZLICHEN GLÜCKWUNSCH ZUM KAUF

DEINES DSL AMP.

Laden sie das vollständige handbuch von

www.marshall.com herunter.

LE FELICITAMOS POR LA COMPRA DE SU

AMPLIFICADOR DSL.

Descargue el manual completo de

www.marshall.com

DSLアンプをお買い上げいただきあ

りがとうございます。

より詳細な操作方法については

http://www.marshall.comで本

製品の取扱説明書を参照してください。

祝贺您购买了DSL放大器。

从www.marshall.com下载完整的手册

CONGRATULAZIONI PER L’ACQUISTO DEL

MARSHALL DSL.

Scaricare il manuale completo su

www.marshall.com

QUICK START GUIDE

Warning! Safety instructions 3

Specication 4

Front panel functions 5

Rear panel functions 7

GUIDE DE DÉMARRAGE

Avertissement ! Consignes de sécurité 8

Spécications 9

Fonctions du panneau avant 10

Fonctions du panneau arrière 12

KURZANLEITUNG

Warnung! Sicherheitshinweise 13

Spezikationen 14

FunktionenanderVorderseite 15

FunktionenanderRückseite 17

GUÍA DE INICIO RÁPIDO

¡Advertencia! Instrucciones de seguridad 18

Especicaciones 19

Funciones de la parte delantera 20

Funciones de la parte posterior 22

GUIDA RAPIDA

Avvertenza! Disposizioni di sicurezza 23

Specichetecniche 24

Funzioni del pannello frontale 25

Funzioni del pannello posteriore 27

快速入门

警告! 安全指南 28

概述与规格 28

前面板功能 29

后面板功能 31

クイックスタート・ガイド

注意！安全上の注意 32

概要と仕様 33

フロントパネル機能 34

リアパネル機能 36

ENGLISH

Warning: Please refer to full details in separate

ImportantSafetyInstructionsCATS-90009.

Warning: beforegoinganyfurther,makesure

that your amp is compatible with your mains

electricity supply. If you have any doubt, please

seekhelpfromaqualiedtechnician–your

Marshall dealer can help you with this.

MAINS INPUT & FUSE

Thespecicmainsinputvoltageratingthatyour

amp has been manufactured for is indicated

on the rear panel of the amp. Never attempt to

bypassthefuseortoneoftheincorrectvalue

or type.

Warning: your amp must be switched off and

disconnected from the mains electricity supply

beforeyoucheckand/orchangeanyfuse.

IMPORTANT SET UP INFORMATION

Follow the start-up procedures below to safely

switch on your amp.

Warning: Failure to follow these instructions may

damage your amp.

1. If using your amp with an extension cabinet,

makesurethepowerhandlingratingofthe

speakercabinetisequaltoorhigherthan

the output power of the amp. Connect

eitherasingle16Ωspeakercabinettothe

singlespeakeroutputontherearpanel,or

asingle8Ωspeakercabinetortwo16Ω

speakercabinetstothepairof8Ωspeaker

outputs.

Note:Whenconnectingaspeakercabinet

makesurethatyouuseaproperspeaker

cable. Never use a screened (shielded)

guitar cable for this purpose.

2. Ensure the power switch is switched off and

set all master volumes on the front panel

to zero.

3. To use the footswitch, connect the

footswitchcabletothefootswitchsocket

on the rear panel of the amp.

4. Connect the supplied mains (power) lead

intothemainsinputontherearpanelrst

and then into an electrical outlet.

5. Plugyourguitarintotheinputjacksocket

on the front panel.

6. Turn the front panel power switch on. The

switch will glow red. Turn the selected

channel volume up to your preferred level

and your amp is ready to play.

TRANSPORTING YOUR EQUIPMENT

Please ensure that your amp is switched off,

unplugged from the mains electricity supply and

all removable cables have been disconnected from

yourequipmentbeforeattemptingtomoveit.

Only move the amp on its own; do not attempt

tomoveitwhileitisstackedontopofacabinet

orotherequipment.

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference interference, and

2. This device must accept any interference

received, including interference that may

cause undesired operation.

Thisequipmenthasbeentestedandfound

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation.

WARNING! SAFETY INSTRUCTIONS

Please read this manual carefully before plugging in. Follow all instructions and heed all

warnings.

ENGLISH

From clean to distorted overdrives, the DSL is

aversatileall-valveamppackedwithfeatures

including an effects loop, power reduction

switch and digital reverb. Your amp has been

specicallydesignedtosoundgreatatarange

of volumes. Perfect for you to use at home, in

rehearsals and studios, or on stage.

MODEL: DSL40CR DSL100HR

Power

40W

(with power

reduction

option to 20W)

100W

(with power

reduction

to 50W)

Valves 4xECC83and

2xEL34

4xECC83

and4x

EL34

Channels 2 (split) “ultra gain” and

“classic gain”

Equalisation

Treble, middle, bass, tone

shift switch, presence,

resonance

Effects Digital reverb

Outputs

5x1/4”jackspeaker

outputs(16Ωload/8Ω

load/4Ωload),

1x¼”jackemulatedlineout

Effects loops Yes,series,send/return,with

loop switch

Speakers

1 x 12”

Celestion

V-Typespeaker

(16Ω,80W)

N/A

Unit weight 22.9kg 24.2kg

Unit width 620mm 740mm

Unit height 490mm 274mm

Unit depth 252mm 242mm

SPECIFICATION

Thisequipmentgenerates,usesandcanradiate

frequencyenergyand,ifnotinstalledandused

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipmentdoescauseharmfulinterference

to radio or television reception, which can be

determinedbyturningtheequipmentoffand

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipmentandthereceiver.

• Connecttheequipmentintoanoutleton

a circuit different from that to which the

receiver is connected.

• Consultthedealeroranexperiencedradio/

TVtechnicianforhelp.

CAUTION:Anychangesormodicationsnot

expressly approved by the party responsible

for compliance may void the users authority to

operatetheequipment.

This device complies with CAN ICES-3(B)/NMB-

3(B).

ENGLISH

FRONT PANEL FUNCTIONS

1. INPUT

Connectyourguitarhereusinga¼”jack

instrument cable.

CLASSIC GAIN CHANNEL

2. GAIN

Controls the gain level for the classic gain

channel. Use this control to adjust the amount

ofinputgain/signalsentintothepreampstage.

Running a higher gain setting increases the level

of distortion in your sound.

3. MODE STATUS LED

This LED lights green to indicate that clean

mode is selected and red to indicate crunch

mode is selected.

4. VOLUME

Controls the volume level of the classic gain

channel.

5. CLEAN/CRUNCH

Press to select clean or crunch mode. The

classicgainchannel’stwomodestakeyour

sound from clean to overdriven tones.

ULTRA GAIN CHANNEL

6. GAIN

Controls the gain level for the ultra gain

channel. Use this control to adjust the amount

ofinputgain/signalsentintothepreampstage.

Running a higher gain setting increases the level

of distortion in your sound.

7. MODE STATUS LED

This LED lights green to indicate that OD1

mode is selected and red to indicate OD2 mode

is selected.

8. VOLUME

Controls the volume level of the ultra gain

channel.

9. OD1/OD2

Press to select OD1 or OD2 mode. The ultra

gainchannel’stwomodestakeyoursoundfrom

distorted to heavy gain tones.

EQUALISATION SECTION

10. TREBLE

Controlsthehigherfrequencycontentofyour

sound.Turningclockwisewillincreasethehighs

makingthesoundbrighter.

11. MIDDLE

Controlsthemiddlefrequenciesofyour

sound.Turningclockwiseincreasesthelevel

ofmidfrequenciesinyoursound.Turning

anti-clockwisereducesthemiddlefrequencies,

‘scooping’thesound–thisisaccentuatedwhen

used in conjunction with Tone Shift.

12. BASS

Controlstheamountoflowerfrequencyinyour

sound.Turningclockwisewillincreasebottom-

endmakingthesoundfuller.

13. TONE SHIFT

ToneshiftreconguresthepreampEQ,giving

you a distinctly different sound. When tone

shiftisengaged,highandlowfrequenciesare

accentuatedandmidfrequenciesarecut.

14. PRESENCE

AdjustthepowerampEQtoaddtrebletoyour

sound.Turningclockwisebringsoutthetopend

frequenciesinyourtone.

15. RESONANCE

AdjustthepowerampEQtoaddbodytoyour

sound.Turningclockwisebringsoutthelowend

frequenciesinyourtone.

Note:TheEQcontrolsarelinked.Alteringthe

setting of one control can change the way

that the other controls behave, so it is worth

ENGLISH

experimentingtondyoursound.

REVERB SECTION

16. CLASSIC REVERB

Controls the reverb level of the classic channel.

17. ULTRA REVERB

Controls the reverb level of the ultra channel.

MASTER VOLUME SECTION

18. MASTER SELECT

Switches between control of Master 1 and

Master 2.

19. MASTER 1

Set the overall volume level of Master 1.

20. MASTER STATUS LED

This LED turns green to indicate that Master

1 is selected and red to indicate Master 2 is

selected.

21. MASTER 2

Set the overall volume level of Master 2.

22. LOOP STATUS LED

This LED turns green to indicate that the FX

loop is on. It is unlit when the FX loop is off.

23. LOOP ON/OFF

This switch turns the FX loop on and off.

24. OUTPUT

Use this switch to reduce power level from

40Wdownto20W,ortoplacetheampinto

standby mode.

25. POWER

This turns the amp on and off.

ENGLISH

26. MAINS INPUT

The supplied mains power lead is connected here.

The mains input voltage rating that your amp has

been built for is shown on the rear panel.

Warning: before powering on, ensure the

amp is compatible with the mains voltage of

the country that the amp is being used in. If

you have any doubt, please get advice from a

qualiedperson.

27. MIDI IN

Connect your external MIDI device here.

28. FX LOOP RETURN

ReturnyoursignalfromexternalFXequipment

hereusinga¼”jackinstrumentcable.

29. FX LOOP SEND

ConnectyourexternalFXequipmenthereusing

a¼”jackinstrumentcable.

30. F/S

Connect the supplied channel footswitch here

(PEDL-90012)oroptionalfootswitch(PEDL-

91016).

31. AUDIO IN

Connect an external device here to practice

with or jam along to music.

32. EMULATED OUT

Frequency-compensatedlineleveloutputfor

headphones. This output features cabinet

emulation by Softube®. This means the sound

from this output includes simulation of the

soundofaspeakerandacab.

33. SPEAKER OUTPUTS

1/4”jackspeakeroutputs.Theyarelabelled

according to the corresponding cabinet setups:

• 1x16Ohm:connecta16Ωspeakercabinet.

• 1x8Ohm/2x16Ohm:connectasingle

8Ωguitarcabinetortwo16Ωcabinets.

REAR PANEL FUNCTIONS

• 1x4Ohm/2x8Ohm:connectasingle4Ω

guitarcabinetortwo8Ωguitarcabinets.

Warning:althoughtheamphasvespeaker

outputs, never attempt to connect more

speakersthanrated.Thesafecombinationsare

listedabove.Anyotherspeakerconguration

may stress or damage the amp.

FRANÇAIS

AVERTISSEMENT ! CONSIGNES DE SÉCURITÉ

Veuillez lire attentivement ce manuel avant de brancher votre appareil. Suivez toutes les

instructions et prenez en compte toutes les mises en garde.

Remarque :lorsquevousconnectez

une enceinte, veillez à utiliser un câble

d’enceinte approprié. N’utilisez jamais un

câble de guitare blindé.

2. Assurez-vousquel’interrupteurd’alimentation

est éteint et réglez tous les volumes sur le

panneau avant à zéro.

3. Pour utiliser la pédale de commande,

connectez le câble de la pédale à la prise de la

pédale sur le panneau arrière de l’ampli.

4. Branchez en premier lieu le cordon

d’alimentation fourni à l’entrée d’alimentation

du panneau arrière, puis ensuite à la prise

électrique.

5. Branchez votre guitare à la prise d’entrée du

panneau avant.

6. Activez l’interrupteur d’alimentation du

panneau avant. Le voyant du commutateur

devient rouge. Augmentez le volume du canal

sélectionnéjusqu’auniveausouhaitéetvotre

ampli est prêt à jouer.

TRANSPORTER VOTRE ÉQUIPEMENT

Veuillezvousassurerquevotreamplicateur

est éteint, débranché de l’alimentation

électriqueetquetouslescâblesamoviblesont

étédéconnectésdevotreéquipementavant

d’essayer de le déplacer.

Déplacezl’amplicateuruniquementseul;

n’essayezpasdeledéplacerlorsqu’ilestempilé

suruneenceinteouunautreéquipement.

DÉCLARATION DE CONFORMITÉ

Cet appareil est conforme à la section 15 de

la réglementation de la FCC. L’utilisation est

soumise aux deux conditions suivantes :

1. L’appareilnedoitpasprovoquer

d’interférences nuisibles, et

2. L’appareil doit pouvoir supporter toutes les

interférences reçues, notamment celles

Avertissement : veuillez vous référer aux détails

complets dans les Instructions de sécurité

importantesspéciquesCATS-90009.

Mise en garde : avant de vous lancer plus

avant,assurez-vousquevotreamplicateurest

compatibleavecvotrealimentationélectrique.

Si vous avez le moindre doute, demandez l’aide

d’untechnicienqualié.VotrerevendeurMarshall

peut vous aider.

ENTRÉE SECTEUR ET FUSIBLE

D’ALIMENTATION

La tension nominale de l’entrée d’alimentation

pourlaquellevotreamplicateurestconçu

estindiquéesurlepanneauarrière.N’essayez

jamais de court-circuiter le fusible ou d’en

utiliser un de valeur ou de type incorrect.

Attention :votreamplicateurdoitêtreéteint

etdéconnectéduréseauélectriqueavantde

vérieret/oudechangerunfusible.

INFORMATIONS IMPORTANTES CONCERNANT

L’INSTALLATION :

Suivez les procédures de démarrage ci-dessous

pour allumer votre ampli en toute sécurité.

Avertissement : si vous ne suivez pas ces

instructions,vousrisquezd’endommagervotre

ampli.

1. SivousutilisezvotreamplicateurDSLavec

uncaissond’extension,assurez-vousque

la puissance nominale du caisson est égale

ou supérieure à la puissance de sortie de

l’amplicateur.Connectezsoituneseule

enceintede16Ωàlasortied’enceinte

uniquedupanneauarrière,soituneseule

enceintede8Ω,oudeuxenceintesde16Ω

àlapairedesortiesd’enceintede8Ω.

FRANÇAIS

Le canal Classic Gain produit des sons limpides

jusqu’àunbreak-upplusagressif.LecanalUltra

Gain fournit encore plus de distorsion et de

break-uppourlesjoueursquirecherchentun

son à gain élevé. Le DSL est doté d’une réverbe

numériquedequalitéprofessionnelleetd’une

boucleFXensérie,cequivouspermetd’obtenir

un son riche à un volume agréable à l’oreille.

MODÈLE : DSL40CR DSL100HR

Puissance

40W(avec

option de

réduction de

puissance à

20W)

100W

(avec

réduction de

puissance à

50W)

Lampes 4xECC83et2

xEL34

4xECC83

et4xEL34

Canaux 2 (split) “ultra gain” et “classic

gain”

Égalisation

Aigus, médiums, graves,

commutateur de changement

de tonalité, présence,

résonance

Effets Réverbenumérique

Sorties

5xprisejack1/4”desortiede

haut-parleur(16Ωdecharge/8Ω

decharge/4Ωdecharge),

1xprise1/4”desortiedeligne

émulée

Boucle

d’effets

Oui,série,envoi/retour,avec

interrupteur à boucle

Haut-parleurs

1 x 12”

Haut-parleur

CelestionV-Type

(16Ω,80W)

S/O

Poids 22.9kg 24.2kg

Largeur 620mm 740mm

Hauteur 490mm 274mm

Profondeur 252mm 242mm

SPÉCIFICATIONS

susceptibles de gêner son fonctionnement.

L’équipementaététestéetdéclaréconforme

auxlimitesimposéesauxappareilsnumériques

de classe B, conformément à la section 15

de la réglementation de la FCC. Ces limites

sont conçues pour fournir une protection

raisonnable contre les interférences nuisibles

dans une installation résidentielle.

Cependant,riennegarantitqu’iln’yaura

pas d’interférences dans une installation

particulière.Sil’équipementprovoquedes

interférences nuisibles à la réception des

signauxderadiooudetélévision,cequipeut

être déterminé en l’éteignant et en le rallumant,

on encourage l’utilisateur à essayer de corriger

ces interférences par l’un des moyens suivants :

• Réorienter ou déplacer l’antenne de

réception.

• Augmenter la distance entre

• l’équipementetlerécepteur.

• Brancherl’équipementsuruneprised’un

circuitdifférentdeceluiauquellerécepteur

est connecté.

• Consulter le revendeur ou un technicien

expérimentéenradio/télévisionpour

obtenir de l’aide.

ATTENTION : Tout changement

oumodicationnonexpressément

approuvé par l’organisme responsable

de la conformité peut annuler le droit de

l’utilisateuràseservirdel’équipement.

Cet appareil est conforme à la norme

CAN ICES-3(B)/NMB-3(B).

Altri manuali per DSL40CR

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Marshall Amplification Altoparlanti

Marshall Amplification

Marshall Amplification EMBERTON II Guida all'installazione

Marshall Amplification

Marshall Amplification STOCKWELL II Manuale utente

Marshall Amplification

Marshall Amplification ACTON III Guida all'installazione

Marshall Amplification

Marshall Amplification Acton Bluetooth Manuale utente

Marshall Amplification

Marshall Amplification EMBERTON II Manuale utente

Marshall Amplification

Marshall Amplification EMBERTON Manuale utente

Marshall Amplification

Marshall Amplification Modefour MF280 Manuale utente

Marshall Amplification

Marshall Amplification Kilburn II Manuale utente

Marshall Amplification

Marshall Amplification MIDDLETON Manuale utente

Marshall Amplification

Marshall Amplification EMBERTON II Guida all'installazione

Marshall Amplification

Marshall Amplification STANMORE III Manuale utente

Marshall Amplification

Marshall Amplification ACTON II Bluetooth Manuale utente

Marshall Amplification

Marshall Amplification ACTON III Istruzioni per l'installazione

Marshall Amplification

Marshall Amplification Woburn Multi-Room Manuale utente

Marshall Amplification

Marshall Amplification WOBURN III Manuale utente

Marshall Amplification

Marshall Amplification WOBURN Manuale utente

Marshall Amplification

Marshall Amplification AST2C Manuale utente

Marshall Amplification

Marshall Amplification STANMORE Manuale utente

Marshall Amplification

Marshall Amplification MOTIF A.N.C. Manuale utente

Marshall Amplification

Marshall Amplification Kilburn II Manuale utente

Marshall Amplification

Marshall Amplification ACTON II Bluetooth Manuale utente

Marshall Amplification

Marshall Amplification WOBURN Manuale utente

Marshall Amplification

Marshall Amplification WOBURN III Manuale utente

Marshall Amplification

Marshall Amplification STANMORE III Guida all'installazione

Manuali Altoparlanti popolari di altre marche

argon audio

argon audio IE20 Manuale utente

Denon

Denon SC-N7 Manuale utente

Gemline

Gemline Ace 3952 Manuale utente

Focal

Focal ON WALL 300 Manuale di istruzioni

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuale utente

SoundLogic

SoundLogic BCCS-6/6395 Manuale utente

Peavey

Peavey DTH 218 Manuale utente

Avantree

Avantree Pluto Air Manuale utente

Morel

Morel Integra Series INTEGRA OVATION 4 Manuale utente

Oppo

Oppo SONICA Manuale utente

Bose

Bose SoundLink Wireless Music System Manuale utente

Rocksteady

Rocksteady Stadium Manuale utente

Bowers & Wilkins

Bowers & Wilkins 4 Manuale utente

Sonance

Sonance SONOS OUTDOOR Series Manuale utente

Electro-Voice

Electro-Voice EVID FM4.2 Manuale utente

Pioneer

Pioneer XW-HTD630 Manuale utente

Onn

Onn BWA16AA002 Manuale utente

HP GL313AA - USB Speakers PC Multimedia Manuale utente