Messoa NDF820 Manuale utente

www.messoa.com

2012-07 A1

Indoor Dome Camera

NDF820/NDF820E

Quick Start Guide

Guia de inicio rápido

Guida rapida

Guide de démarrage rapide

Краткое руководство

クイックスタートガイド

快速安裝指南

快速安装指南

NDF820/NDF820E l Quick Start Guide 1

English

Safety Instructions

Make sure the supplied voltage meets the power consumption

requirements of the camera before powering the camera on.

Incorrect voltage may cause damage to the camera.

The camera should be protected from water and moisture, excessive

heat, direct sunlight and cold.

This installation should be made by a qualied service person and

should conform to all local codes.

Unplug the camera during lightening storms or when unused for

long periods of time.

No part of this document may be reproduced or transmitted in any form

or by any means, electronic or mechanical, for any purpose, without

the express written permission of MESSOA.

Disclaimer

Specications and information contained in this document are

presented as accurately as possible as of the time of release, but

are not guaranteed to be entirely free of error. MESSOA assumes no

responsibility for errors or omissions that may appear in this document

and reserves the right to change this publication at any time without

obligation to notify anyone of such revisions or changes.

2 NDF820/NDF820E l Quick Start Guide

1. Introduction

1.1 Package Contents

Indoor Dome Camera x1

CD-ROM (User manual and IP Finder utility) x1

Quick Start Guide x1

Guide Pattern Sticker x1

RJ-45 Female / Female Coupler x1

Accessories

• Machine Type Flat Head Screw (#1) x4

• Tapping Type Flat Head Screw (#2) x4

• Plastic Anchor (#3) x4

• Rubber Foot (#4) x4

123 4

NDF820/NDF820E l Quick Start Guide 3

English

1.2 Hardware Overview

Connectors

1. PowerIn(Red+/Black-): power connector, DC12V/AC24V

2. RJ-45EthernetConnector: network & PoE (Power over Ethernet)

connection

3. BNC: composite video output

4 NDF820/NDF820E l Quick Start Guide

2. Installation

2.1 Mounting the Camera

This camera is designed for ceiling & wall mounts depending on users

requirements. Mount the camera to your intended location.

Disassembling

1. Take off the dome cover screw.

2. Rotate the dome cover counterclockwise to unlock and pull free of

the housing.

3. Then remove the inner liner by gently pulling it free of the two

notches in the housing.

3. Inner Liner

2. Dome Cover 1. Dome Cover Screw

Drilling the Mounting Surface

1. Post the “Guide Pattern” sticker on the mounting surface.

NDF820/NDF820E l Quick Start Guide 5

English

2. Aiming the circles (the gure below marked with “+“ ) on the

sticker, drill four screw holes and one cable entry hole in the

ceiling/wall.

Lens Direction

Note: Mounting surface material

determines screw type.

Refer to manual.

GUIDE PATTERN

Mounting the Camera

1. Insert the plastic anchors into the screw holes (this gure take the

tapping type screws as the example to illustrate the mounting).

2. Tapping Type Screws

3. Inner Liner

4. Dome Cover

1. Plastic Anchors

Guide Pattern Sticker

5. Dome Cover Screw

6 NDF820/NDF820E l Quick Start Guide

2. Use the tapping screws to secure the camera base to the surface.

TipCautionWarning

Note

1. Use the machine type screws if you are attaching the camera to

a pendent mounting. Use the tapping type screws for all other

surfaces.

2. For cement surfaces, insert the “Plastic Anchors” into the holes. For

softer surfaces, do not use the “Plastic Anchors”.

3. Use the Rubber Feet for surface mounting.

Adjusting Camera Angle

Check the monitored view by wiring the RCA jack to a monitor. With an

external monitor connected, you can adjust pan and tilt angles of the

camera for appropriate or better view.

RCA Jack for

Composite Video Output

PanAdjustment:Rotate the lens base to adjust the horizontal angle.

TiltAdjustment:Tilt the lens base to adjust the vertical angle.

NDF820/NDF820E l Quick Start Guide 7

English

Tilt Angle = 90 degrees

Pan Angle = about 355 degrees

Horizontalrotation: Rotate the dome base to adjust the horizontal

position. Do not turn the base more than 355° as this may cause the

internal cables to twist and disconnect or break.

Horizontal Rotation = 355 degrees

8 NDF820/NDF820E l Quick Start Guide

TipCautionWarning

Note

When the tilt angle is less than 82 degrees, there is no distortion.

V=49.9° (Field of View)

82° Tilt Angle

Distortion

Area

Assembling the Camera

Follow the steps below when all the camera adjustments and cabling

tasks are nished.

1. Assemble the inner liner.

2. Assemble the dome cover.

3. Secure the dome cover with the accompanying screw.

2.2. Initial Conguration via a PC

Before connecting the camera to your network infrastructure, it’s

suggested that you connect the camera to a computer rst to perform

initial congurations.

1. Configure the computer’s IP address that must be on the

same network segment with the camera’s default IP address

(192.168.1.30 by default), such as:

• IPAddress:192.168.1.100

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Messoa Telecamera di sicurezza

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente