National Instruments NI 9802 Manuale utente
Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | sales@artisantg.com | www.artisantg.com
SM
View
Instra
OPERATING INSTRUCTIONS AND SPECIFICATIONS
NI 9802
2 SD Card Memory Module
ni.com/manuals
DeutschFrançais
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
NI 9802 Operating Instructions and Specifications 2 ni.com
This document describes how to use the National Instruments 9802
and includes specifications for the NI 9802. Visit ni.com/info and
enter rdsoftwareversion to determine which software youneed
for the modules youare using. For information about installing,
configuring, and programming the system, refer to the system
documentation. Visit ni.com/info and enter cseriesdoc for
information about C Series documentation.
Note The NI 9802 is supported only in CompactRIO
reconfigurable chassis, such as the cRIO-910x, and
Single-Board RIO devices.
Note The safety guidelines and specifications in this
document are specific to the NI 9802. The other
components in the system might not meet the same safety
ratings and specifications. Refer to the documentation for
each component in the system to determine the safety
ratings and specifications for the entire system. Visit
ni.com/info and enter cseriesdoc for information
about C Series documentation.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 3 NI 9802 Operating Instructions and Specifications
Safety Guidelines
Operate the NI 9802 only as described in these operating
instructions.
Hot Surface This icon denotes that the component may be
hot. Touching this component may result in bodily injury.
Safety Guidelines for Hazardous Locations
The NI 9802 is suitable for use in Class I, Division 2, Groups A, B,
C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4, and
Ex nA IIC T4 hazardous locations; and nonhazardous locations
only. Follow these guidelines if youare installing the NI 9802 in a
potentially explosive environment. Not following these guidelines
may result in serious injury or death.
Caution Do not insert or remove SD Cards unless power
has been switched off or the area is known to be
nonhazardous.
Caution Do not remove modules unless power has been
switched off or the area is known to be nonhazardous.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
NI 9802 Operating Instructions and Specifications 4 ni.com
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Zone 2 applications, install the system
in an enclosure rated to at least IP 54 as defined by
IEC 60529 and EN 60529.
Special Conditions for Hazardous Locations Use in Europe
This equipment has been evaluated as Ex nA IIC T4 equipment
under DEMKO Certificate No. 07 ATEX 0626664X. Each module
is marked II 3G and is suitable for use in Zone 2 hazardous
locations, in ambient temperatures of –40 °C ≤Ta ≤70 °C. If you
are using the NI 9802 in Gas Group IIC hazardous locations, you
must use the device in an NI chassis that has been evaluated as
Ex nC IIC T4, EEx nC IIC T4, Ex nA IIC T4, or Ex nL IIC T4
equipment.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 5 NI 9802 Operating Instructions and Specifications
Special Conditions for Marine Applications
Some modules are Lloyd’s Register (LR) Type Approved for
marine applications. To verify Lloyd’s Register certification, visit
ni.com/certification and search for the LR certificate, or
look for the Lloyd’s Register mark on the module.
Caution To meet radio frequency emission requirements
for marine applications, use shielded cables and install
the system in a metal enclosure. Suppression ferrites
must be installed on power supply inputs near power
entries to modules and controllers. Power supply and
module cables must be separated on opposite sides of the
enclosure and must enter and exit through opposing
enclosure walls.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
NI 9802 Operating Instructions and Specifications 6 ni.com
Inserting and Removing SD Cards
The NI 9802 is an SD Card storage module that can read from and
write to SD Cards. The NI 9802 has two SD Card slots into which
youcan insert NI-approved SD Cards.
Note Using SD Cards that are not approved by NI might
invalidate specifications and result in unreliable
performance.
Note The NI 9802 supports only SD Cards formatted in
FAT16.
The card slots each have a door to protect the SD Cards while in
the module. Each door is connected to a switch that indicates to the
NI 9802 software when it is safe to read from or write to the
SD Card.
The NI 9802 has four LEDs that indicate which slots contain an
SD Card and if the SD Card is active. Refer to Figure 1 for the
designation of SD Card slots and LEDs. Refer to Table 1 for
descriptions of each of the LEDs on the NI 9802 and when it is safe
to remove SD Cards from the NI 9802.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 7 NI 9802 Operating Instructions and Specifications
Figure 1. NI 9802 Card Slots and LEDs
1 Present (Card 0)
2 Busy (Card 0)
3 Present (Card 1)
4 Busy (Card 1)
5 Card Slot Doors
6 SD Card Slot 1
7 SD Card Slot 0
5
6
7
2
4
1
3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
NI 9802 Operating Instructions and Specifications 8 ni.com
LEDs
Table 1. LED Descriptions
LED SD Card Slot Description
Present (Card 0),
Green
SD Card Slot 0 This LED is lit when an SD Card is
in Slot 0 and the SD Card slot door
is closed.
Busy (Card 0),
Yellow
SD Card Slot 0 This LED is lit when the card in
Slot 0 is active. This LED is
flashing when the NI 9802 is
performing I/O on the card in
Slot 0. Do not remove the SD Card
while this LED is lit or flashing.
Present (Card 1),
Green
SD Card Slot 1 This LED is lit when an SD Card is
in Slot 1 and the SD Card slot door
is closed.
Busy (Card 1),
Yellow
SD Card Slot 1 This LED is lit when the card in
Slot 1 is active. This LED is
flashing when the NI 9802 is
performing I/O on the card in
Slot 1. Do not remove the SD Card
while this LED is lit or flashing.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 9 NI 9802 Operating Instructions and Specifications
SD Card Slot Doors
Do not open an SD Card slot door or remove an SD Card while the
yellow LED for that card is lit or flashing. If youopen an SD Card
slot door while the yellow LED for that card is lit or flashing, the
NI 9802 software acts to protect the file system of the SD Card.
Refer to the software help for more information. Visit ni.com/
info and enter cseriesdoc for information about C Series
documentation.
Caution Opening an SD Card slot door or removing an
SD Card while the yellow LED for that card is lit or
flashing might result in incomplete or lost data.
Yo umust close the slot door for the NI 9802 software to read from
or write to the SD Card.
Note Screw the slot doors closed completely using a
#1 Phillips screwdriver. Do not overtighten.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Indice
Altri manuali National Instruments Unità di controllo
National Instruments
National Instruments C Series Manuale utente
National Instruments
National Instruments SCC-TC Series Manuale utente
National Instruments
National Instruments NI 9217 Manuale utente
National Instruments
National Instruments PXIe-8246 Manuale utente
National Instruments
National Instruments NI-9206 Manuale utente
National Instruments
National Instruments NI 4472 Manuale utente
National Instruments
National Instruments 9759 Manuale utente
National Instruments
National Instruments NI 9215 Manuale
National Instruments
National Instruments REM-11178 Manuale utente
National Instruments
National Instruments FIeldPoint FP-AO-200 Manuale utente
National Instruments
National Instruments 9205 Manuale
National Instruments
National Instruments SCXI Series Manuale utente
National Instruments
National Instruments sbRIO-9205 Manuale utente
National Instruments
National Instruments NI 9229 Manuale
National Instruments
National Instruments FlexRIO PXI-79 R Series Manuale utente
National Instruments
National Instruments 9225 Manuale
National Instruments
National Instruments PXIe-4322 Manuale utente
National Instruments
National Instruments NI 9381 Manuale utente
National Instruments
National Instruments NI 9503 Manuale utente
National Instruments
National Instruments ATCA-3671 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
