National Instruments NI 9403 Manuale utente
OPERATING INSTRUCTIONS AND SPECIFICATIONS
NI 9403
32-Channel, TTL Digital Input/Output Module
ni.com/manuals
DeutschFrançais
NI 9403 Operating Instructions and Specifications 2 ni.com
This document describes how to use the National Instruments 9403
and includes specifications and pin assignments for the NI 9403.
Visit ni.com/info and enter rdsoftwareversion to determine
which software youneed for the modules youare using. For
information about installing, configuring, and programming the
system, refer to the system documentation. Visit ni.com/info
and enter cseriesdoc for information about C Series
documentation.
Note The safety guidelines and specifications in this
document are specific to the NI 9403. The other
components in the system might not meet the same safety
ratings and specifications. Refer to the documentation for
each component in the system to determine the safety
ratings and specifications for the entire system. Visit
ni.com/info and enter cseriesdoc for information
about C Series documentation.
© National Instruments Corp. 3 NI 9403 Operating Instructions and Specifications
Safety Guidelines
Operate the NI 9403 only as described in these operating
instructions.
Hot Surface This icon denotes that the component may be
hot. Touching this component may result in bodily injury.
Safety Guidelines for Hazardous Locations
The NI 9403 is suitable for use in Class I, Division 2, Groups A, B,
C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4, and
Ex nA IIC T4 hazardous locations; and nonhazardous locations
only. Follow these guidelines if youare installing the NI 9403 in a
potentially explosive environment. Not following these guidelines
may result in serious injury or death.
Caution Do not disconnect I/O-side wires or connectors
unless power has been switched off or the area is known
to be nonhazardous.
Caution Do not remove modules unless power has been
switched off or the area is known to be nonhazardous.
NI 9403 Operating Instructions and Specifications 4 ni.com
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Zone 2 applications, install the system
in an enclosure rated to at least IP 54 as defined by
IEC 60529 and EN 60529.
Caution For Zone 2 applications, connected signals must
be within the following limit:
Capacitance .......................... 0.02 μF max
Special Conditions for Hazardous Locations Use in Europe
This equipment has been evaluated as Ex nA IIC T4 equipment
under DEMKO Certificate No. 07 ATEX 0626664X. Each module
is marked II 3G and is suitable for use in Zone 2 hazardous
locations. If youare using the NI 9403 in Gas Group IIC hazardous
locations or in ambient temperatures of –40 °C ≤Ta ≤70 °C, you
must use the device in an NI chassis that has been evaluated as
EEx nC IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
© National Instruments Corp. 5 NI 9403 Operating Instructions and Specifications
Special Conditions for Marine Applications
Some modules are Lloyd’s Register (LR) Type Approved for
marine applications. To verify Lloyd’s Register certification, visit
ni.com/certification and search for the LR certificate, or
look for the Lloyd’s Register mark on the module.
Caution To meet radio frequency emission requirements
for marine applications, use shielded cables and install
the system in a metal enclosure. Suppression ferrites
must be installed on power supply inputs near power
entries to modules and controllers. Power supply and
module cables must be separated on opposite sides of the
enclosure and must enter and exit through opposing
enclosure walls.
NI 9403 Operating Instructions and Specifications 6 ni.com
Connecting the NI 9403
The NI 9403 has a 37-pin DSUB connector that provides
connections for the 32 digital input/output channels.
Figure 1. NI 9403 Pin Assignments
DIO16
DIO17
DIO18
DIO19
DIO20
DIO21
DIO22
DIO23
COM
COM
DIO24
DIO25
DIO26
DIO27
DIO28
DIO29
DIO30
DIO31
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
DIO6
DIO7
COM
COM
DIO8
DIO9
DIO10
DIO11
DIO12
DIO13
DIO14
DIO15
RSVD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
© National Instruments Corp. 7 NI 9403 Operating Instructions and Specifications
Each channel has a DIO pin to which youcan connect a digital
input or output device. The 32 DIO channels are internally
referenced to COM, so youcan use any of the four COM lines as a
reference for the external signal.
Yo ucan independently configure each DIO channel in software for
input or output. The DIO channels have Schmitt trigger inputs and
are compatible with 5 V TTL logic devices. Each input channel has
hysteresis for improved performance with noisy and
non-monotonic input signals. Each channel also has a pull-down
resistor and includes overvoltage, overcurrent, and short-circuit
protection. Refer to the Specifications section for more information
about input thresholds and overvoltage protection. Refer to the
Overcurrent/Short-Circuit Protection section for more
information about overcurrent and short-circuit protection.
© National Instruments Corp. 9 NI 9403 Operating Instructions and Specifications
Overcurrent/Short-Circuit Protection
The overcurrent protection allows only a specified amount of
current through the output channels to protect the NI 9403 from
short circuits. If the NI 9403 goes into an overcurrent state, the
module sets all the DIO channels to high impedance for
approximately 280 milliseconds. When the channels are in this
state, the NI 9403 can accept new line direction configuration and
output state data but cannot pass valid input data to the software.
After the protection period, the NI 9403 automatically recovers to
the latest direction configuration and output state. If the
overcurrent condition still exists, the module again sets the
channels to high impedance. This cycle continues until the
overcurrent condition is removed. Refer to the Specifications
section for more information about the maximum output current.
Sleep Mode
This module supports a low-power sleep mode. Support for sleep
mode at the system level depends on the chassis that the module is
plugged into. Refer to the chassis manual for information about
support for sleep mode. If the chassis supports sleep mode, refer to
the software help for information about enabling sleep mode. Visit
NI 9403 Operating Instructions and Specifications 10 ni.com
ni.com/info and enter cseriesdoc for information about
C Series documentation.
Typically, when a system is in sleep mode, youcannot
communicate with the modules. In sleep mode, the system
consumes minimal power and may dissipate less heat than it does
in normal mode. Refer to the Specifications section for more
information about power consumption and thermal dissipation.
Specifications
The following specifications are typical for the range –40 to 70 °C
unless otherwise noted. All voltages are relative to COM unless
otherwise noted.
Input/Output Characteristics
Number of channels.......................... 32 DIO channels
Input/output type............................... TTL, single-ended
Default power-on line direction ........ Input
Altri manuali per NI 9403
2
Indice
Altri manuali National Instruments Scheda di rete
National Instruments
National Instruments NI 9265 Manuale utente
National Instruments
National Instruments IMAQ Vision for LabWindows TM /CVI Manuale utente
National Instruments
National Instruments NI 781xR Manuale utente
National Instruments
National Instruments NI 6013 Manuale utente
National Instruments
National Instruments Module NI PXI-8250 Manuale utente
National Instruments
National Instruments NI 6232 Manuale utente
National Instruments
National Instruments NI PXI-1056 Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
National Instruments
National Instruments Monochrome Image Acquisition Device NI 1410 Manuale utente
National Instruments
National Instruments NI 9235 Manuale utente
National Instruments
National Instruments Network Device DAQ S Manuale utente
National Instruments
National Instruments Measure Data Acquisition Manuale utente
National Instruments
National Instruments NI 9852 Manuale utente
National Instruments
National Instruments NI 9219 Manuale utente
National Instruments
National Instruments MXI Series Manuale utente
National Instruments
National Instruments NI PCIe-8255R Manuale utente
National Instruments
National Instruments NI 9481 Manuale utente
National Instruments
National Instruments NI 9233 Manuale utente
National Instruments
National Instruments Isolated Current Output Module SCC-CO20 Manuale utente
National Instruments
National Instruments Network Adapter NI PXIe-1075 Manuale utente
