TRENDnet TEG-PCITXR Manuale utente
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCITXR
Version 08.24.04
10/100/1000Mbps Gigabit Network Adapter
User’s Guide
Le Guide de l'utilisateur du
Adaptateur réseau Gigabit 10/100/1000Mbps
Diese Benutzeranleitung
10/100/1000MBit/s Gigabit-Netzwerk-Adapter
Esta guía del usuario
Adaptador de Red Gigabit a 10/100/1000Mbps
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
3
4
7
11
1. Introduction .......................................................................................
2. Hardware Installation ........................................................................
3. Software Installation ..........................................................................
4. Configuring TCP/IP Protocol .............................................................
Congratulations on purchasing your new 10/100/1000Mbps Gigabit PCI
Adapter. This Gigabit PCI Adapter is easy to install and suitable for a 10, 100,
or 1000Mbps Ethernet network. With Gigabit performance, you can enjoy
lightening fast file transfer, uninterrupted video/audio streaming, and excellent
response time for network gaming.
Features
– IEEE 802.3, 802.3u and 802.3z compliant
– Support 32-bit 33/66Mhz PCI Local Bus Master high-speed operation of
Rev.2.1/2.2 specification
– Plug-and-Play installation
– One RJ-45 connector: Auto detection of 10Mbps Ethernet, 100Mbps Fast
Ethernet and 1000Mbps Gigabit Ethernet & Auto MDI-X
– Supports 10/100/1000Mbps Auto-negotiation operation
– Full Duplex support for 10/100/1000Mb/s data rates
– Auto MDI-II/MDI-X crossover for all three speeds
– Two LED indicators (Link, Activity) for easy diagnostic
1
1. Introduction
English UG
English
2English
Package Contents
Gigabit PCI Adapter LED
CAUTION:
Under ordinary circumstances, the 32-bit PCI 10/100/1000Mbps Gigabit
Ethernet Card will not be affected by static charge as may be received through
your body during handling of the unit. However, there are special
circumstances where you may carry an extraordinarily high static charge, and
possibly damage the card and/or your computer. It is good practice to eliminate
all static electricity by touching a ground (an unpainted metal area of your
computer chassis, for example) before performing any installations.
If any item is found missing or damaged, please contact your local reseller for
replacement.
Link (10, 100, 1000)
The Link LED indicates the connection speed of the adapter.
ACT
The ACT LED flashes when there is network activity.
User’s Guide
TEG-PCITXR 3.5" Driver Diskette
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCITXR
Version 08.24.04
10/100/1000Mbps Gigabit Network Adapter
User’s Guide
Le Guide de l'utilisateur du
Adaptateur réseau Gigabit 10/100/1000Mbps
Diese Benutzeranleitung
10/100/1000MBit/s Gigabit-Netzwerk-Adapter
Esta guía del usuario
Adaptador de Red Gigabit a 10/100/1000Mbps
3
2. Hardware Installation
Each Gigabit Network Adapter is equipped with an RJ-45 port that
automatically adjusts the connection speed to 10Mbps, 100Mbps or 1000Mbps;
allowing your PC to attach to Ethernet, Fast Ethernet or Gigabit Ethernet
networks.
For best results, we recommend using Category 5E or higher twisted-pair RJ-
45 cable. However, if you are connecting the adapter to 10Base-T (10Mbps)
network, you can use Category 3 or higher cable. For 100Base-TX (100Mbps)
and 1000Base-T (1000Mbps) networks, please use Category 5 or higher
cables.
The hardware installation is now complete. Next step is to load the
adapter driver and configure your PC's operating system to work with the
Gigabit Adapter.
1. Power off your PC and any peripherals attached to it and unplug your PC's
power cord.
2. Remove computer's cover.
3. Open your computer and locate the PCI slot(s) on your motherboard. PCI
slots are easily identified by their beige or white color, and by the fact that
network cards fit snugly into them. Remove the metal slot cover on the back
of the PC and then insert the Gigabit Adapter into any available PCI slot.
4. Once your Gigabit Adapter is firmly in place, secure it on your PC's
chassis with a screw.
5. Replace your PC's cover.
6. Connect one end of the Category 5/5E cable to the Adapter's RJ-45 port
and another end to a Gigabit Switch or Adapter.
7. Reconnect your PC's power, then power on your computer.
If your computer has Windows Operating System, the computer would
automatically recognize the Adapter as a new hardware and start the driver
installation wizard. Follow the instructions in the Software Installation
section to install the adapter driver.
For computers with Netware Server/Client and Linux, please go to HELP
folder from the driver diskette and select the desired operating system to
view the driver installation procedures.
English
Overview
Installing Gigabit PCI Adapter into your Pcs
4
1. Start up your computer.
2. Windows 98 automatically detects the presence of the Gigabit adapter.
3. Insert the Driver Diskette into your floppy drive when the Add New
Hardware Wizard window appears and click Next.
4. Select Search for the best driver for your device (Recommended). Click
Next.
5. Select Specify a location, type A:\win98 in the drop down box and click
Next (assuming A: drive is the floppy drive).
6. Windows is now ready to install the Gigabit Adapter driver. Click Next to
continue.
7. Windows will begin copying the driver files to your PC.
At this point, the installation may require files from your Windows 98 CD-
ROM. When this happens, insert your Windows 98 CD-ROM into your CD-
ROM drive and select CD-ROM drive (on the screen) to load the files.
8. After Windows has finished copying the files, it will prompt you to restart
your PC. Remove the diskette and CD-ROM and click YES to restart the
PC.
3. Software Installation
English
Installing the Driver for Windows 98
5English
1. Start up your computer.
2. Windows ME automatically detects the presence of the Gigabit adapter.
3. Insert the Driver Diskette into your floppy drive when the "Add New
Hardware Wizard" window appears and click Next.
4. Select Specify the location of the driver (Advanced). Click Next.
5. Select Search for the best driver for your device (Recommended) and
check the Specify a location, enter A:\winme (assuming A: drive is the
floppy drive), and click Next.
6. Windows is now ready to install the Gigabit Adapter driver. Click Next to
continue.
7. Windows will begin copying the driver files to your PC. At this point, the
installation may require files from your Windows ME CD-ROM. When this
happens, insert your Windows ME CD-ROM into your CD-ROM drive and
select CD-ROM drive (on the screen) to load the files.
8. After Windows has finished copying the files, it will prompt you to restart
your PC. Remove the diskette and CD-ROM and click YES to restart the
PC.
1. Start up your computer. You must have administrative rights to perform
the installation.
2. The Found New Hardware window appears
3. Insert the Driver Diskette into your floppy drive
4. Select Search for a suitable driver for my device (Recommended) and
click Next.
5. At the Locate Driver Files dialog box, select Specify a location, click Next,
type A:\win2k and click OK. The Driver file search results dialog box
appears. Click Next to continue.
6. At Microsoft's digital Signature window, click YES to continue the
installation.
7. Click Finish to complete the driver installation.
Installing the Driver for Windows ME
Installing the Driver for Windows 2000
6English
1. Start up your computer. You must have administrative rights to perform
the installation.
2. The Found New Hardware window appears
3. Insert the Driver Diskette into your floppy drive
4. Select Install from a list or specific location option and click Next.
5. Select Search for the best driver in these locations and select Include
these location option and type A:\winxp and click OK. The Driver file
search results dialog box appears. Click Next to continue.
6. At Microsoft's digital Signature window, click Continue Anyway to continue
the installation.
7. Click Finish to complete the driver installation.
After the driver files are loaded for Windows, the Gigabit network adapter is
now ready for operation. If your network requires configuring TCP/IP protocol,
please proceed to configure the PC's TCP/IP protocol to communicate with the
existing network.
Installing the Driver for Windows XP
7English
4. Configuring TCP/IP Protocol
1. On the Desktop, right-click My Network Places and click Properties. Then,
right-click Wireless Network Connection and click Properties; the Network
Connection Properties Window will appear
2. Under the General tab, select Internet Protocol (TCP/IP) and click the
Properties button; the Internet Protocol (TCP/IP) Properties Window will
appear.
Configure TCP/IP protocol settings to match your network.
1. Select the Obtain an IP address automatically option.
2. Select the Obtain DNS server address automatically option.
3. Click OK to save the settings.
Windows 2000/XP
i.For DHCP IP address Setup (this should work for
most network environments)
8
1. Select the Use the following IP address option and enter the IP, Subnet
Mask, and Default gateway addresses.
2. Select the Use the following DNS server address option and enter DNS
addresses.
1. On the Desktop, right-click Network Neighborhood and click Properties.
Then, right-click Wireless Network Connection and click Properties; the
Wireless Network Connection Properties Window will appear.
2. Under Configuration tab, select Realtek RTL 8169/8110 Gigabit Ethernet
NIC (TCP/IP protocol) and click on the Properties button; the TCP/IP
Protocol Properties Window will appear
ii.For Static IP address Setup
For Windows 98/ME users
3. Click OK to save the settings.
English
Altri manuali per TEG-PCITXR
7
Questo manuale è adatto per i seguenti modelli
1
Altri manuali TRENDnet Scheda di rete
TRENDnet
TRENDnet TPL-101U Manuale utente
TRENDnet
TRENDnet Te100-pciwn Manuale utente
TRENDnet
TRENDnet TEW-603PI Manuale utente
TRENDnet
TRENDnet TE100-PC16R Manuale utente
TRENDnet
TRENDnet TEW-PC16 Manuale utente
TRENDnet
TRENDnet TPL-410APK Manuale utente
TRENDnet
TRENDnet TEW-226PC Manuale utente
TRENDnet
TRENDnet TU2-ETG Manuale utente
TRENDnet
TRENDnet TEW-641PC Manuale utente
TRENDnet
TRENDnet TEW-501PC Manuale utente
TRENDnet
TRENDnet TEG-PCITXM Manuale utente
TRENDnet
TRENDnet TEW-642EC Manuale utente
TRENDnet
TRENDnet WN8020A Manuale utente
TRENDnet
TRENDnet TEW-USB Manuale utente
TRENDnet
TRENDnet TEW-421PC Manuale utente
TRENDnet
TRENDnet TE100-PCIWA Manuale utente
TRENDnet
TRENDnet TFM-CF56 Manuale utente
TRENDnet
TRENDnet TEG-PCISX Manuale utente
TRENDnet
TRENDnet TEM-560T Manuale utente
TRENDnet
TRENDnet TE100-PCIWA Manuale utente
Manuali Scheda di rete popolari di altre marche
Cisco
Cisco MC16E Manuale utente
Delta Electronics
Delta Electronics Braking Modules VFDB Series Manuale utente
TwinMOS
TwinMOS Booming Manuale utente
Dialogic
Dialogic Media Board DM/V1200BTEPEQ Manuale utente
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
