NGS ROLLER CREEK Manuale utente
roller creek
USER’S MANUAL
www.ngs.eu
ENGLISH IFRANÇAIS IESPAÑOL I DEUTSCH IITALIANO
PORTUGUÊS IPOLSKI INEDERLANDS IČESKY I
ΕΛΛΗΝΙΚΑ
roller
CREEK
Bluetooth true wireless
waterproof IPX7 speaker
IMPORTANT!
Close the rear rubber correctly
to prevent water getting in
ENGLISH
OVERVIEW
1 2 3 4
5 6
1 Power on/power off
2 Volume – / previous track
3 Volume + / next track
4 Play/pause
5 Micro SD card slot
6 Micro USB charging port
USER’S MANUAL
BLUETOOTH SPEAKER PAIRING
RECONNECTING
1. Hold down the button for 3 seconds, a message
sound “beep” will announce from speaker and the mode
LED will blinking in blue; the device is turned ON and
goes into searching / paring / reconnect mode for pair.
2. Now, turn ON the Bluetooth function on your mobile
phone.
3. Search for “NGS ROLLER CREEK” and select it to pair
(for first time pairing or pairing a new mobile device).
4. The Bluetooth speaker will be reconnecting
automatically if your mobile phone has been
paired (Depend on the of mobile phone’s type and
configuration, manual reconnection may require on
some devices).
CHARGING THE BLUETOOTH
SPEAKER
1. Connect the Bluetooth speaker’s micro USB socket with
the computer’s USB port through USB cable.
2. The charging LED will turn ON in red light; the
rechargeable battery is in charging.
3. The charging LED red light will turn OFF when the
rechargeable battery is fully charged.
4. Disconnect the USB cable.
ENGLISH
BLUETOOTH SPEAKER CONTROL
FUNCTION
1. In playing music, press button to pause music, press
it once again to play.
2. Press the + button to increases the volume level.
3. Press the – button to decreases the volume level.
4. Press and hold the + button to play next music file.
5. Press and hold the – button to play previous music file.
MODES
BLUETOOTH / MICRO SD CARD
To switch between modes, press the key. If the device is
not connected to a micro SD card, it will skip this mode.
5. If pairing is successful, a message sound; “beep” will
announce from speaker and the mode LED light will
keep turn on.
USER’S MANUAL
HAND FREE FUNCTION
BLUETOOTH MODE ONLY
When there is an incoming call;
1. The ringing sound will up and the playing music will
pause automatically.
2. Press button to pick up the call if you want.
3. Now you have hand free function with the Bluetooth
speaker.
4. Hold down the button for 2 seconds to hand up the
call when finished. And,
5. The paused music will start to play automatically.
HOW TO CONNECT 2
LOUDSPEAKERS TO EACH OTHER
1. In order to connect th em to each other, both speakers
must be the same model; NGS Roller Creek.
2. Turn on both speakers and press the play/pause button
on each of them for 5 seconds. You will hear a beep and
the blue LED will flash.
3. Now press the power button on one of them twice (you
will hear 2 consecutive beeps) and enter True Wireless
pairing mode. Once paired, you will hear another beep,
and the blue LED of the secondary device (the one on
which we have not yet pressed the power button) will
remain fixed, while the other light will flash.
4. Open the bluetooth options on your mobile device
(phone, tablet, computer, etc...) and select the NGS
ROLLER CREEK device.
5. In this manner, they will be synchronised and ready to
use with your mobile device.
ENGLISH
If at any time in the future you should need
to dispose of this product please note that:
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist.
Check with your Local Authority or retailer
for recycling advice.
(Waste Electrical and Electronic Equipment
Directive)
Battery warranty: The battery is a consumer product, and
as such it is under warranty for 12 months.
MICRO SD CARD MODE
1. IInsert the micro SD card or a USB flash drive into the
slot.
2. The device will automatically play any music in MP3
format on the card or USB flash drive.
roller
CREEK
Haut-parleurs Bluetooth
TRUE WIRELESS étanches IPX7
IMPORTANT!
Fermez correctement le
caoutchouc arrière pour
empêcher la pénétration de l’eau
FRANÇAIS
APERÇU GENERAL
1 2 3 4
5 6
1 On/off (allumer/éteindre)
2 Volume – / piste précédente
3 Volume + / piste suivante
4 Lecture / Pause
5 Emplacement pour la carte Micro
6 Connecteur micro USB pour la charge
MANUEL DE L’UTILISATEUR
COUPLAGE RECONNEXION DU
HAUTPARLEUR BLUETOOTH
1. Maintenez le bouton enfoncé, un message est
diffusé par le haut-parleur et le voyant LED bleu du
mode clignote;le dispositif s’allume et passe au mode
de recherche / couplage / reconnexion pour réaliser le
couplage.
2. Activer maintenant la fonction Bluetooth sur votre
téléphone mobile.
3. Rechercher le “NGS ROLLER CREEK” et le sélectionner
pour effectuer le couplage (pour le premier couplage ou
pour le couplage d’un nouveau dispositif mobile).
4. Le haut-parleur Bluetooth rétablira automatiquement
la connexion à votre téléphone mobile si celui-ci a été
couplé précédemment (cela dépend du type et de la
configuration du téléphone mobile, certains dispositifs
peuvent requérir la reconnexion manuelle).
CHARGEMENT DU HAUT
PARLEUR BLUETOOTH
1. Raccorder la prise micro USB du haut-parleur Bluetooth
au port USB à l’aide du câble USB.
2. Le voyant LED rouge de charge s’allume; la batterie
rechargeable est en cours de chargement.
3. Le voyant LED rouge de charge s’éteint; la batterie
rechargeable est complètement chargée.
4. Débrancher le câble USB.
Indice
Lingue:
Altri manuali NGS Altoparlanti
NGS
NGS WILDDISCO Manuale utente
NGS
NGS Roller Tumbler Manuale utente
NGS
NGS WILDTRAP 3 Manuale utente
NGS
NGS SKYLINE Manuale utente
NGS
NGS WILD DUB 2 Manuale utente
NGS
NGS WILDPUNK Series Manuale utente
NGS
NGS NITRO 1 Manuale utente
NGS
NGS roller flash Manuale utente
NGS
NGS WILD DUB ZERO Manuale utente
NGS
NGS ROLLER BYRON 360 Manuale utente
NGS
NGS WILDMAMBO Manuale utente
NGS
NGS Sky Gazer Manuale utente
NGS
NGS ROLLER ROCKET Manuale utente
NGS
NGS SKY CHARM Manuale utente
NGS
NGS roller Trick Manuale utente
NGS
NGS SKYDUSk Manuale utente
NGS
NGS Roller Tempo Manuale utente
NGS
NGS Roller Cube Manuale utente
NGS
NGS ROLLER PINEAPPLE Manuale utente
NGS
NGS ROLLER SLANG Manuale utente
