OHAUS TD52 Manuale utente

Altri manuali per TD52

7

Indice

Altri manuali OHAUS Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

TD52 Indicator

Li-ion Battery Option

Instruction Manual

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-1

1. INTRODUCTION

Please read this manual completely before installation and operation.

CAUTION:

READ ALL SAFETY WARNINGS BEFORE INSTALLING, MAKING

CONNECTIONS, OR SERVICING. FAILURE TO COMPLY WITH THESE

WARNINGS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE. RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE.

1.1 Kit Contents

Battery with attached

battery cover.

2. INSTALLATION

2.1 Safety Precautions

For safe and dependable operation of this equipment, please comply with all safety

precautions mentioned in this manual.

Disconnect equipment from mains power supply before installation.

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-2

2.2 Installation procedure

Follow the steps below. Refer to the figures when performing these steps.

For TD52P:

1. Separate the indicator from the base by disconnecting the load cell cable from the male

connector at the back of the Indicator. Remove the interface option cover.

2. Connect the 7-pin Li-ion Battery Pack power cable to the main board battery connector

as shown.

Cable

Battery Connector

Arrow

Load cell cable male connector

Interface option cover

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-3

3. Place the Li-ion Battery Pack so Slots 1 on the bottom right edge of the Battery Pack

align with the Rib on the bottom of the Indicator Option Area. Slide the Battery Pack to

the right (in the direction of the arrow) until the Slots engage with the Rib.

4. Twist the Li-ion Battery Pack cable a half turn and connect the 7 Pin connector from

the Indicator to the Battery Pack. Secure the Battery Pack with with one screw at the

location marked Boss Screw 9.

5. Put the interface option cover back on the terminal.

Li-ion Battery Pack 7 pin

connector

Screw

Arrow

Rib

Boss post 9

Slot 1

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-4

For TD52XW:

1. Remove the interface option cover. Release the 6 screws with sealed washers.

2. Rotate the rear housing forward away from the front housing as shown.

Screw

Load cell cable male connector

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-5

3. Connect the 7-pin Li-ion Battery Pack power cable to the main board battery connector

as shown.

4. Place the Li-ion Battery Pack so Slot 1 on the bottom right edge of the Battery Pack

align with the Rib on the bottom of the Indicator Option Area. Slide the Battery Pack to

the right (in the direction of the arrow) until the Slots engage with the Rib.

Cable

Battery connector

Slots 1

Arrow

Rib

Boss post 9

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-6

5. Twist the Li-ion Battery Pack cable a half turn and connect the 7 Pin connector from

the Indicator to the Battery Pack. Secure the Battery Pack with with one screw at the

location marked Boss Screw 9.

Connect the cable to Li battery packing 7 pin connectors.

6. Put the rear housing back on the front housing. Re-install the 6 screws with sealed

washers.

For TD52XW withreversed rear cover:

1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as

shown.

7 Pin Connector

Screw

Screw

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-7

2. Take the rear housing down from the front housing as shown.

3. Connect the cable to the main board battery connector 3.

Cable

Battery connector 3

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-8

4. Install the Li battery packing. Push it along the arrow. (Note: slot 2 match with the rib of

the red part).

5. Secure it with one screw (Note: Boss Post is 10). Connect the cable to Li battery

packing 7 pin connectors.

6. Put the rear housing back on the front housing. Re-install the 6 screws. Fasten the 6

screws with sealed washer (Torque is 1.8N*m± 0.5).

Slot 2

Rib

Boss post 10

7 Pin connector

screw

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187

EN-9

3. BATTERY OPERATION

3.1 Battery Icon

During battery operation, the battery icon indicates the battery charge level remaining.

Battery 5 - 25 % remaining

Battery 25 - 50 % remaining

Battery 50 - 75 % remaining

Battery 75 - 100 % remaining

The battery icon is located above the weighing unit on the indicator display, as can be seen

in the image below.

When battery level is below 5% the indicator will shut down automatically.

It takes about 9 hours to fully charge the battery.

4. BATTERY SPECIFICATIONS

Battery Type:

Lithium-Ion, 2500mAh, 7.4V

Battery Operating Time:

21 hours* with backlight off

Battery Charging Time:

9 hours

Operating Temperature Range:

-20 °C ~ 60 °C (-4 °F ~ 140 °F)

Charging Temperature Range:

0°C ~ 45°C (32°F ~ 113 °F)

Note:

* The number of hours the balance can run on the battery depends on many factors.

Backlight, and Interface Options will all reduce the hours before a recharge is needed. For

optimum battery life, turn these features off.

Battery icon

www. .com information@itm.com1.800.561.8187 www. .com information@itm.com1.800.561.8187