Onicon F-4300 Istruzioni di montaggio

F-4300 Clamp-on Ultrasonic Thermal Energy Measurement System

Installation Hardware Instruction for Clamp-on Thermowells

CON

Flow and Energy Measurement

DOC-0004103 Rev.A

ONICON Incorporated • 11451 Belcher Road South • Largo, FL 33773 • USA • www.onicon.com

IMPORTANT NOTE

ONICON BTU meters are

precision measuring devices

that must be installed

according to the instructions

contained in this document

in order to maintain their

accuracy and reliability.

For Use with Kit: INSTL0501-TSC & INSTL0502-TSC

Please read entire manual before installing the meter.

The two temperature sensors must be located in such a manner

as to accurately measure only the temperature of the supply line

entering and the return line leaving the portion of the piping

system for which the energy measurement is being made.

If possible, nd an easily accessible location where wire

connections can be made from oor level. This will facilitate any

future service.

One temperature sensor thermowell will need to be placed in the same pipe as the mounting

brackets. If it is an immersion thermowell, it must be located on the downstream side of the mounting

brackets.

The downstream distance between the thermowell and brackets should be at least ve (5) pipe

diameters, leaving enough clearance to remove either sensor from the pipe without interference from

the other sensor.

IMPORTANT NOTE:

Place the temperature sensors away from strong sources of electrical noise that might aect the

performance of the sensors.

FLOW DIRECTION

CLAMP-ON FLOW METER

INSTALLATION LOCATION

CLAMP-ON

THERMOWELL ASSEMBLY

TYPICAL THERMOWELL INSTALLATION

F-4300 Clamp-on Ultrasonic Thermal Energy Measurement System

Installation Hardware Instruction for Clamp-on Thermowells

CON

Flow and Energy Measurement

DOC-0004103 Rev.A

ONICON Incorporated • 11451 Belcher Road South • Largo, FL 33773 • USA • www.onicon.com

Directions for Installation:

1. Remove junction box cover and set aside.

2. Attach the provided Velcro or the enclosure mounting hardware in the desired location as

shown below.

JUNCTION BOX COVER

PROVIDED VELCRO

727.447.6140 Page 3 onicon.com

CON

Flow and Energy Measurement

F-4300 Clamp-on Ultrasonic Flow Meters

Installation Hardware Instruction for Clamp-on Thermowell

3. Apply a thin coat of thermal compound to the temperature sensor, and gently insert the

temperature sensor all the way into the clamp-on thermowell.

4. Apply thermal compound to the heat sink and install the clamp-on thermowell on to the pipe

using the pipe strap as shown.

Directions for Installation (Continued):

11451 Belcher Road South • Largo, FL 33773 • USA • (P) 727.447.6140 • (F) 727.442.5699 • onicon.com

CON

Flow and Energy Measurement

5. Connect the Signal (+) and Reference (-) wires from the transmitter to the F-4300 BTU meter

through the strain relief. Be sure to observe the polarity of the connection, positive to positive

and negative to negative. Shield wires should be connected at the F-4300, but left open at the

temperature sensor transmitter.

TRANSMITTER

STRAIN RELIEF

6. Tighten the strain reliefs and reinstall the junction box cover. Once the thermowells and sensors

are fully installed and tested, insulate the thermowells and the pipe to complete the installation.

Directions for Installation (Continued):

If you have any questions or need assistance, please contact ONICON Sales at (727) 447-6140 or

[email protected].

Altri manuali per F-4300

Altri manuali Onicon Strumento di misura

Onicon

Onicon System-10 BTU Meter Manuale utente

Onicon

Onicon F-3500 Istruzioni operative

Onicon

Onicon FT-3400 Istruzioni operative

Onicon

Onicon F-4300 Istruzioni operative originali

Onicon

Onicon FT-4600 Istruzioni operative

Onicon

Onicon F-5000 Istruzioni operative

Onicon

Onicon System-10 BTU Meter Manuale utente

Onicon

Onicon FT-3000 Series Manuale utente

Onicon

Onicon Fox Thermal FT2A Manuale utente

Onicon

Onicon F-3100 Series Istruzioni per il montaggio

Onicon

Onicon F-4400 Manuale utente

Onicon

Onicon F-1000 SERIES Manuale utente

Onicon

Onicon FB-3500 Istruzioni operative

Onicon

Onicon F-5200 Istruzioni operative

Onicon

Onicon D-1401 Istruzioni operative

Onicon

Onicon D-100 Istruzioni operative

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Onicon

Onicon D-100 Istruzioni operative

Onicon

Onicon F-4300 Istruzioni operative originali

Onicon

Onicon D-100 Manuale utente

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Onicon

Onicon SYSTEM-1000 Istruzioni operative

Onicon

Onicon SYSTEM-40 Istruzioni operative

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente