PRECISION DIGITAL ProVu Series Manuale utente

Thank you for your purchase of the

 PD6000 process meter.



describe some of the common setup

procedures for this meter.

This guide includes:



Basic Wiring for  Meter..............

Program and Scale the Input...............

Program Relays for Automatic Reset...

Program Custom Unit Tags..................

Program 4-20 mA Analog Output.........

Reset Meter to Factory Defaults..........

For additional information about the

 PD6000 meter not covered in

this quick start guide, please consult

the instruction manual included on the

CD or available at www.predig.com.

Menu Button – Use this button to

access Programming Mode and to

return to Run Mode.

Note: If you think you have made a mistake while

programming the meter, use this button to

return the meter to Run Mode without saving.

Right/F1 Button – Use this button to

change the selected digit while input-

ting a numeric value in Programming Mode.

Up/F2 Button – Use this button to

increment the selected digit while

inputting a numeric value in Programming

Mode.

Enter/F3 Button – Use this but-

ton to access or accept a menu

item while in Programming Mode.

ERIES

233 South Street

Hopkinton MA 01748-2208 USA

Tel. (508) 655-7300 www.predig.com

MeterView Pro

USB Install

 PD6000 Process Meter

Quick Start Guide





onboard USB. The meter is powered by the USB connection, so there is no need to wire

anything prior to programming the meter.

®Pro

Connect the provided USB cable to the

meter and the computer as shown. The

computer will automatically install the driver

software it needs to talk to the meter.

Note: Only one meter may be connected at a time.



with the meter software.

Once the driver is installed, an AutoPlay dialog

should appear for the drive “MAINSTAL.” Click



If the computer does not display an AutoPlay

dialog for the drive “MAINSTAL,” you should

open My Computer and double-click on the

drive labeled “MAINSTAL.”



The program will open a few windows and

install two programs on your computer. Simply

follow the onscreen instructions until you see

one of the dialogs in step 4.

Note: If you receive a User Account Control

warning, click “Yes.”

If there is an update available, click the

“Update” button to install the new version.

-

ming your meter.

Note:-

ware, you will be asked if you want to update



This way, you will always have the most cur-

rent version on the meter for future installs.

Note:





1 2

 PD6000 Process Meter Quick Start Guide

󰀩-

nectors. Connect your wires to the provided connectors and plug into the meter as indicated.

Basic Wiring for  Meter

4-20 mA Input Wiring

Wiring for a 4-20 mA input using either an external

power supply or self powered transmitter.

Wiring for a 4-20 mA input using internal power

supply.



4-20 mA Output Wiring1

Relay Connections2

AC and DC

Loads Protection



Loads Protection

F4 Digital Input Connection



1

2

Consult the PD6000 instruction

manual located on the included CD

or available online at www.predig.com

for additional wiring diagrams.

Active



Passive



+ -- +

External

Power

Supply

2-Wire

4-20 mA

Transmitter

INPUT SIGNAL

- +

INPUT SIGNAL

2-Wire 4-20 mA

Self-Powered

Transmitter

P- COMP+ V+ mA+

3 41 2 5

P- COMP+ V+ mA+

3 4

12 5

INPUT SIGNAL

3-Wire 4-20 mA

Transmitter

Signal

2-Wire 4-20 mA

Transmitter

INPUT SIGNAL

P- COMP+ V+ mA+

3 41 2 5

P- COMP+ V+ mA+

3 41 2 5

Voltage

Signal

INPUT SIGNAL INPUT SIGNAL

3-Wire Voltage

Transducer

Signal

P- COMP+ V+ mA+

3 41 2 5

P- COMP+ V+ mA+

3 41 2 5

12-35 VDC

Power

Supply

4-20 mA

Input Meter

RI- I+

13 2

RELAY1

3 2 1

24 V

4-20 mA Input

Remote Display,

Chart Recorder, Etc.

RI- I+

MA OUT

13 2

RELAY1

3 2 1

24 V

MA OUT

C NONO NC NC C

RELAY4 RELAY3

4 36 5 2 1

C NONO NC NC C

RELAY2 RELAY1

4 36 5 2 1

P- COMP+ V+ mA+

3 41 2 5

AC or DC

POWER

Required External Fuse:

5 A max, 250 V Slow Blow

POWER

 PD6000 Process Meter Quick Start Guide

Program and Scale the Input

Program the 



InP 1 &

InP 2

For example: If the meter were used to display the level of a 100 ft tall tank, the transmitter should send

a 4 mA signal when the tank is empty and a 20 mA signal when the tank is full. The meter should be

programmed to interpret these inputs on a display range of 0-100, so that at 4 mA the meter will display

0.00 and at 20 mA the meter will display 100.00.

Press to

enter Programming

Mode, press to

access the SEtup

Press to ac-

cess the InPut



Press to select

-

age (mA or Volt

and press to accept the input type.

Press multiple

times, until the dec

pt

menu is displayed and press to access.

Press until the

desired decimal

point location is

displayed and press to accept.

Press to ac-

cess the d-SCAL



press to select yes or no, then press .

Note: Most applications only require one scaling

point (select no



On the Setup tab, un-

der Input Type, select

the desired input.

On the Program-

ming tab, select the

desired decimal

point location.

Under Scale Values,

enter the desired

low and high display

values in the Display column.

Click the Send

Meter Data button

to send your programmed settings to the

meter.

1 2

3 4



1 2

5 6

 PD6000 Process Meter Quick Start Guide

Press to

access the ProG



Press to ac-

cess the SCALE



Press three

times, until dis 1



is displayed. Use to change which

digit is selected and to increment the

selected digit. Press when done.

Press three

times, until dis 2

(High Display

Use to change

which digit is selected and to increment

the selected digit. Press when done.

Press to return to Run Mode.

Program Relays for Automatic Reset

Program the 󰀨

relays at reset points.

Note: If the set point is higher than the reset point, the relay will be a high alarm. If the set point is

 than the reset point, the relay will be a .



On the Relays tab,

in the desired relay

section, select “Auto”

from the Action drop

down list.

Enter the set and

reset point values in



Click the Send

Meter Data button

to send your programmed settings to the

meter.

Note:

programmed in this manner. It is

not necessary to send your pro-

grammed settings to the meter after

each relay is programmed, simply

repeat steps 1 & 2 for each relay

then send to the meter.

1 2

Press to

enter Programming

Mode, press to

access the SEtup

Press until

the relay

menu is displayed

and then press to access.



7 8

9 10

1 2

 PD6000 Process Meter Quick Start Guide

Press until the

appropriate relay

number is displayed

(rly 1-8press to access.

Press to accept

Auto (Automatic



Press to access

the set (Relay Set



Use to change

which digit is

selected and

to increment the selected digit. Press

when done to accept the new set point

value.

Press to access

the rst (Relay Re-



Use to change

which digit is

selected and

to increment the selected digit. Press

when done to accept the new set point

value. Press to return to Run Mode.

Press to access

the Act (Relay Ac-



Note: Use 󰀨

during step 3. If you need to pro-

gram more relays, simply repeat

steps 3-9 for each additional relay.

Consult the  PD6000 Instruc-

tion Manual for information on

additional relay action types.

Program Custom Unit Tags

Program the  meter to display custom unit tags for the process value. Display line 2

shows this custom unit tag by default.

Note:

custom unit tag is simply for ease of reading.



On the Setup tab, in

the Display section,

enter your desired





count as two because they require two LEDs.

Click the Send

Meter Data button

to send your programmed settings to the

meter.

1 2

 PD6000 Process Meter Quick Start Guide



Press to

enter Programming

Mode, press to

access the SEtup

Press until the

units

is displayed and

then press to access.

The meter will

display the default



here that the letter 'm' uses two 7 segment

LEDs. This is true of the letter 'w' as well.

Use to change

which letter is

selected and to

increment to the next letter. Press when

done to accept the new custom unit tag.

Program 4-20 mA Analog Output

Program the  meter to output an analog signal based on its display value. This signal

is commonly output to a PLC or chart recorder.

Note: The display values programmed for 4-20 analog output do not need to be the same as those

programmed as input scale values, though they most commonly will be.



On the Setup tab,

under Analog Out

Scale, enter your



Click the Send

Meter Data button

to send your programmed settings to the

meter.



Press to

enter Programming

Mode, press to

access the SEtup

Press until the

aout

menu is displayed

and then press to access.

Press to access

the dis 1 (Display

This is the

display value at which the low range of the

output will be transmitted.

Use to change

which digit is

selected and

to increment the selected digit. Press

when done to accept the new display value.

1 2

3 4

 PD6000 Process Meter Quick Start Guide

LIM6000QS_C - 06/168

Press to access

the Out 1 (Output

This is the

output signal which represents diS 1.

The default value

of 04.000 (4.000



most applications. Press to accept.

Press to ac-

cess the

dis 1 

menu. This is the display value at which the

high range of the output will be transmitted.

Use to change

which digit is

selected and to

increment the digit. Press when done.

Press to access

the

Out 2 

menu. This is the output signal which repre-

sents diS 2.

The default value of

20.000

should work for

most applications. Press to accept the

default value.

Return Meter to Factory Defaults

If a mistake has been made while programming the meter and it is unclear where the error

occurred, the best option may be to perform a factory reset of the meter and begin again.

Press and hold



enter the Advanced

Features menu.

Press until the

diAG

menu is displayed.

Press and hold

until the meter

rESEt

 to reset the

meter.

The meter will



segments and then

display ProcES





On the Advanced Features

tab, in the bottom left-hand corner, click the

Reset Meter Factory Defaults button.

-

dow that appears, click

OK. The meter will reset to factory defaults.

9 10

1 2

3 4

 PD6000 Process Meter Quick Start Guide

Altri manuali per ProVu Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PRECISION DIGITAL Strumento di misura

PRECISION DIGITAL

PRECISION DIGITAL Javelin D PD644 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Trident PD765 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6800 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD686 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6080 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL SABRE T PD743 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD213 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PROVU PD6001 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Sabre P PD603 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD660 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader PD683 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader PD6620 Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6400 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL DART PD602 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6100 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6701 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProVu Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6060 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD677 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6200 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL pd6300 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6060 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProVu Series Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente