RS PRO ICM 134 Manuale utente

Instruction Manual

ICM 134

Clamp Meter

EN DE ES IT FR



EN - 2

Safety Information

Read and understand this Instruction

Manual completely before using this

instrument. Failure to observe the warnings

and cautions in this Instruction Manual may

result in injury or death, or damage to the

instrument and other equipment or

property.

If this instrument is used in a manner not

specified in these instructions, the protec-

tion provided by the instrument may be

impaired.

WARNING

-Examine the instrument and probes and

leads before use. Do not use the instru-

ment if it is wet or damaged, or if you

suspect it is not operating correctly.

-When using the instrument, test leads or

probes, keep your fingers behind the

finger guards.

-Remove the test lead from the instrument

before opening the battery cover or instru-

ment case.

-Always use the correct terminals, switch

position and range for measurements.

-Verify the instrument is operating correctly

by measuring a known voltage before

use. If in doubt, have the instrument

serviced.

-Do not apply more than the rated voltage

as marked on the instrument between

terminals, or between any terminal and

earth ground.

-Use caution when measuring voltages

above 30 Vac rms or 60 Vdc. These

voltages pose a shock hazard.

-To avoid incorrect readings that can lead

to electric shock, replace the battery as

soon as low battery indicator appears

in the display.

-Disconnect the circuit power and

discharge all high-voltage capacitors

before making resistance, continuity, or

diode measurements.

-Do not use the instrument in a Hazardous

Area or around explosive gasses or

vapours.

EN - 3

-Wear suitable Personal Protective

Equipment when working around or near

hazardous Live conductors which could

be accessible.

-Do not use the thermocouple to measure

the temperature of Hazardous Live

conductors or equipment.

Caution

-Disconnect the test leads from the test

points before changing the position of the

function rotary switch.

-Never connect the instrument to a source

of voltage with the function rotary switch in

Ω/ ;/Aposition.

- If possible, do not work alone, so

assistance can be given if required.

-Do not expose the instrument to extremes

of temperature or high humidity.

-If this instrument is used in the vicinity of

equipment which generates electro

magnetic interference, the display may

become unstable or the measurements

may be subject to large errors.

The following symbols may appear on

the instrument and in this Instruction

Manual:

Risk of electric shock

Refer to Instruction Manual

 Direct Current (dc)

Alternating Current (ac)

<Battery

Earth

Equipment protected throughout by

double or reinforced insulation

Conforms to EU directives

Dispose of this equipment in

accordance with local regulations.

EApplication around and removal

from hazardous Live conductors is

permitted.

EN - 4

Maintenance

Do not attempt to repair this Instrument. It

contains no user-serviceable parts. Repair

or servicing should only be performed by

qualified personnel. This instrument

should be calibrated yearly, or more

frequently if used in harsh conditions or if

it is suspected of being inaccurate.

For calibration and repair contact RS

Components - the address is given at the

end of these instructions.

Cleaning

Periodically wipe the case with a damp

cloth and detergent. Do not use abrasives

or solvents.

EN - 5

To conserve battery power, the Auto Power

-off function will turn the instrument off

approximately 10 minutes after the last

operation.

10min

To disable the Auto Power-off function:

Turn the instrument off, press and hold the

“Backlight” button and turn the rotary switch

to the required function. The auto Power-off

is disabled until the next time the instru-

ment is turned off and on again.

Power On / Off

Auto Power Off

EN - 6

ACV / DCV

Resistance

EN - 7

Diode / Continuity

;

EN - 8

DC µA

Capacitance

Note –To improve the measurement

accuracy of a small value capacitor, record

the reading with the test leads open circuit,

then substract the residual capacitance of

the Instrument and leads from the final

measurement.

CUNKNOWN =CMEASUREMENT - CRESIDUAL

EN - 9

Temperature

Data Hold

392A

EN - 10

ACA

392A

CAT.Ⅲ.600V

with respect to

earth for the jaw.

Tactile Barrier for

hand guard.

Do not hold

the meter across

the Tactile Barrier.

OK I + (-I) = 0

Back Light

Indice

Altri manuali RS PRO Strumento di misura

RS PRO

RS PRO SLM 1353M Manuale utente

RS PRO

RS PRO ISM 410 Manuale utente

RS PRO

RS PRO RS-1361C Manuale utente

RS PRO

RS PRO RS-8890G Manuale utente

RS PRO

RS PRO RS-1260 Manuale utente

RS PRO

RS PRO RS-8890D Manuale utente

RS PRO

RS PRO RS-137 Manuale utente

RS PRO

RS PRO DT-388 Manuale utente

RS PRO

RS PRO 123-8776 Manuale utente

RS PRO

RS PRO RS-90 Manuale utente

RS PRO

RS PRO RSST-2000 Series Manuale utente

RS PRO

RS PRO RS-1360A Manuale utente

RS PRO

RS PRO RS-91 Manuale utente

RS PRO

RS PRO RS 155B Manuale utente

RS PRO

RS PRO ISM 400 Manuale utente

RS PRO

RS PRO IM-191 Manuale utente

RS PRO

RS PRO IPM 3600N Manuale utente

RS PRO

RS PRO ICM A6N Manuale utente

RS PRO

RS PRO RS-9985 Manuale utente

RS PRO

RS PRO 877-1791 Manuale utente

RS PRO

RS PRO ISA-730 Manuale utente

RS PRO

RS PRO RS-95 Manuale utente

RS PRO

RS PRO ICM 20 Manuale utente

RS PRO

RS PRO RSPRO-P30R Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente