RS PRO ICM A6N Manuale utente

Instruction Manual

ICM A6N

Clamp Meter

EN DE ES IT FR



1000Vdc

CAT

750Vac

CAT

600V

EN - 2

Safety Information

Read and understand this Instruction

Manual completely before using this

instrument. Failure to observe the warnings

and cautions in this Instruction Manual may

result in injury or death, or damage to the

instrument and other equipment or property.

If this instrument is used in a manner not

specified in these instructions, the protec-

tion provided by the instrument may be

impaired.

The following symbols may appear on

the instrument and in this Instruction

Manual:

Risk of electric shock

Refer to Instruction Manual

Alternating Current (ac)

<Battery

Earth

Equipment protected throughout by

double or reinforced insulation

Conforms to EU directives

Dispose of this equipment in

accordance with local regulations.

EApplication around and removal

from hazardous Live conductors is

permitted.

WARNING

-Examine the instrument and probes and

leads before use. Do not use the instru-

ment if it is wet or damaged, or if you

suspect it is not operating correctly.

-When using the instrument, test leads or

probes, keep your fingers behind the

finger guards.

-Remove the test lead from the instrument

before opening the battery cover or instru-

ment case.

-Always use the correct terminals, switch

position and range for measurements.

EN - 3

-Verify the instrument is operating correctly

by measuring a known voltage before

use. If in doubt, have the instrument

serviced.

-Do not apply more than the rated voltage

as marked on the instrument between

terminals, or between any terminal and

earth ground.

-Use caution when measuring voltages

above 30 Vac rms or 60 Vdc. These

voltages pose a shock hazard.

-To avoid incorrect readings that can lead

to electric shock, replace the battery as

soon as low battery indicator <appears

in the display.

-Disconnect the circuit power and

discharge all high-voltage capacitors

before making resistance, continuity, or

diode measurements.

-Do not use the instrument in a Hazardous

Area or around explosive gasses or

vapours.

-Wear suitable Personal Protective

Equipment when working around or near

hazardous Live conductors which could

be accessible.

Caution

-Disconnect the test leads from the test

points before changing the position of the

function rotary switch.

-Never connect the instrument to a source

of voltage with the function rotary switch in

Ω/ ;/Aposition.

- If possible, do not work alone, so

assistance can be given if required.

-Do not expose the instrument to extremes

of temperature or high humidity.

EN - 4

Maintenance

Do not attempt to repair this Instrument. It

contains no user-serviceable parts. Repair

or servicing should only be performed by

qualified personnel. This instrument

should be calibrated yearly, or more

frequently if used in harsh conditions or if

it is suspected of being inaccurate.

For calibration and repair contact RS

Components - the address is given at the

end of these instructions.

Cleaning

Periodically wipe the case with a damp

cloth and detergent. Do not use abrasives

or solvents.

EN - 5

Power On / Off

• When first turned on, the instrument

displays the remaining capacity of the

battery. Replace the battery when 0% is

shown or the low battery symbol “<”

remains visible in the display.

After a successful battery self-test, the

instrument will automatically select resis-

tance (Ω)/continuity mode.

Auto Hold Enable / Disable

Auto Power Off Enable / Disable

EN - 6

Self-Testing Aid

Fail of usage

Ready to use

CAT.Ⅲ.600V

with respect to

earth for the jaw.

Barrier for

Hand Guard

Do not hold

the meter above

the Barrier

• Do not attempt to measure while power-

ing up, as it will cause the self-test to fail.

Caution

If “FAIL” is shown in the display, do not use

the instrument as an internal fault has

occurred.

AC Current measurement

EN - 7

AC V / DC V

Caution

When connecting the test leads to the

circuit or device, connect the black lead

before the red lead. When removing the

test leads, remove the red lead before

the black lead.

•Input Impedance

Note : The input impedance is≧4K for an

input voltage up to 30V and increases

automatically with input voltage to approxi-

mately 375KΩat 750V.

EN - 8

Continuity

Resistance / Diode

EN - 9

Priority of function

The LCD display shows volt-

age mode, when the voltage at

the input terminals satisfies the

following conditions:

ACV:

Between 1.3V and 999.9V

DCV:

Between 2.1V and 999.9V,

or between -0.7V ~ -999.9V

The LCD display shows

resistance (Ω) mode when the

resistance at the input termi-

nals satisfies the following

conditions:

Resistance:

Between 0 and ∞Ω

ACV: Between 0 and 0.9V

DCV: Between -0.4 and -0.2V

DCV: Between 1.0 and 2.0V

The LCD display shows diode

mode when the voltage at the

input terminals satisfies the

following conditions:

DCV: Between 0.4 and 0.8V

The LCD display shows AC

current (A) mode when the

current sensed by the jaws

satisfies the following

conditions :

ACA:

Between 0.9A and 600.0A

Data Hold

Data-hold mode is not available when

“OL KΩ“ is displayed with no input

Signal present.

EN - 10

Data Hold Beep Guard

The internal sounder will beep continuously

and the LCD display will flash if either of

the following two situations are met in Data

-hold mode :

1. The instrument measures a

characteristic different from the LCD

reading; e.g. a voltage reading is held

on the display and an attempt is made to

measure an AC current .

2. The measured signal is the same

characteristic as the LCD reading, but

is 50 counts or more greater than the

held LCD reading.

Auto Hold ( ACA only )

Indice

Altri manuali RS PRO Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente