Siemens SIMATIC ET 200SP TM ECC 2xPWM ST Manuale utente

SIMATIC

ET 200SP

Technology module TM ECC

2xPWM ST (6FE1242-6TM10-

0BB1)

Manual

04/2018

A5E42681298B

-AA

Preface

Documentation guide

Product overview

Wiring

Configuring/address space

Programming

Interrupts/diagnostic

messages

Technical specifications

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E42681298B-AA

Ⓟ

05/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury

may

result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 3

Preface

Purpose of the documentation

This manual contains module-specific information on wiring, diagnostics as well as the

technical specifications of the technology module.

General information on installation and commissioning of the ET 200SP is available in the

ET 200SP System Manual.

Conventions

Please take into account the notes marked as follows:

Note

A note contains important information on the product described in t

his documentation, its

handling and to a section of the documentation to which you should pay particular attention.

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens' products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be

connected to an enterprise network or the internet if and to the extent such a connection is

necessary and only when appropriate security measures (e.g. firewalls and/or network

segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit.

Siemens' products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers' exposure

to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under.

Preface

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

4Manual, 04/2018, A5E42681298B-AA

See also

IndustrialSecurity (http://www.siemens.com/industrialsecurity)

http://support.automation.siemens.com (http://support.automation.siemens.com)

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 5

Table of contents

Preface ................................................................................................................................................... 3

1 Documentation guide .............................................................................................................................. 7

2 Product overview .................................................................................................................................. 11

2.1 Properties................................................................................................................................11

3 Wiring ................................................................................................................................................... 17

3.1 Terminal assignment and power supply .................................................................................17

3.2 Connection examples .............................................................................................................25

4 Configuring/address space.................................................................................................................... 31

4.1 Configuring..............................................................................................................................31

4.2 Reaction to CPU STOP ..........................................................................................................32

4.3 Required I/O address space ...................................................................................................32

4.4 Parameter ...............................................................................................................................33

4.5 Control and feedback interface...............................................................................................35

4.5.1 Assignment of the control interface ........................................................................................35

4.5.2 Assignment of the feedback Interface ....................................................................................37

5 Programming ........................................................................................................................................ 41

5.1 General information ................................................................................................................41

5.2 "ECC4100" functions ..............................................................................................................41

5.3 FC ECC4100 parameters .......................................................................................................42

6 Interrupts/diagnostic messages............................................................................................................. 47

6.1 Status and error displays ........................................................................................................47

6.2 Interrupts.................................................................................................................................50

6.3 Diagnostics alarms..................................................................................................................50

6.4 Device defect ..........................................................................................................................52

7 Technical specifications ........................................................................................................................ 53

7.1 Technical specifications ..........................................................................................................53

Index..................................................................................................................................................... 57

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

Manual, 04/2018, A5E42681298B-AA 7

Documentation guide

The documentation for the SIMATIC S7-1500 automation system and the SIMATIC

ET 200MP distributed I/O system is arranged into three areas.

This arrangement enables you to access the specific content you require.

Basic information

The System Manual and Getting Started describe in detail the configuration, installation,

wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7

online help supports you in the configuration and programming.

Device information

Product manuals contain a compact description of the module-specific information, such as

properties, wiring diagrams, characteristics and technical specifications.

General information

The function manuals contain detailed descriptions on general topics regarding the SIMATIC

S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web

server, OPC UA.

You can download the documentation free of charge from the Internet

(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-

overview/Pages/Default.aspx).

Changes and supplements to the manuals are documented in a Product Information.

Documentation guide

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)

8Manual, 04/2018, A5E42681298B-AA

You can download the product information free of charge from the Internet

(https://support.industry.siemens.com/cs/us/en/view/68052815).

Manual Collection S7-1500/ET 200MP

The Manual Collection contains the complete documentation on the SIMATIC S7-1500

automation system and the ET 200MP distributed I/O system gathered together in one file.

You can find the Manual Collection on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86140384).

SIMATIC S7-1500 comparison list for programming languages

The comparison list contains an overview of which instructions and functions you can use for

which controller families.

You can find the comparison list on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86630375).

"mySupport"

With "mySupport", your personal workspace, you make the best out of your Industry Online

Support.

In "mySupport", you can save filters, favorites and tags, request CAx data and compile your

personal library in the Documentation area. In addition, your data is already filled out in

support requests and you can get an overview of your current requests at any time.

You must register once to use the full functionality of "mySupport".

You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).

"mySupport" - Documentation

In the Documentation area in "mySupport" you can combine entire manuals or only parts of

these to your own manual.

You can export the manual as PDF file or in a format that can be edited later.

You can find "mySupport" - Documentation on the Internet

(http://support.industry.siemens.com/My/ww/en/documentation).

"mySupport" - CAx data

In the CAx data area in "mySupport", you can access the current product data for your CAx

or CAe system.

You configure your own download package with a few clicks.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Siemens Unità di controllo

Siemens

Siemens 7KM9300-0AE01-0AA0 Manuale utente

Siemens

Siemens 3AK Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens Cerberus Pyrotronics NIM-1M Manuale utente

Siemens

Siemens XLD-1 Manuale utente

Siemens

Siemens XC1001-A Manuale

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens SINAMICS G130 Manuale utente

Siemens

Siemens SINAMICS G110M Manuale utente

Siemens

Siemens SICAM A8000 Series Manuale utente

Siemens

Siemens ET 200S 1SI Manuale elenco delle parti

Siemens

Siemens SINUMERIK 840D Manuale utente

Siemens

Siemens SIMATIC FM 351 Manuale utente

Siemens

Siemens MEM-1 Manuale utente

Siemens

Siemens SIMATIC 505 Istruzioni operative

Siemens

Siemens SITRANS AW 7MP3112 Series Manuale utente

Siemens

Siemens SITRANS F M MAGFLO series Manuale utente

Siemens

Siemens SENTRON 7KM9300-0AM00-0AA0 Manuale utente

Siemens

Siemens SITOP DC UPS 6EP1931-2DC21 Manuale utente

Siemens

Siemens LME11 series Manuale utente

Siemens

Siemens SR-35 Manuale utente

Siemens

Siemens SIPROTEC4 7SJ61 Manuale utente

Siemens

Siemens SIRIUS 3RT1916-4KA Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente