SNBC BT-T080 Manuale del proprietario

PROGRAMMING MANUAL

KIOSK Printer

BT-T080

Shandong New Beiyang Information Technology Co.,Lt

CONFIDENTIAL

BT-T080 Programming Manual

- 1 -

Declaration

If you need this manual, please comply with the clause below.

If you disagree with it, please return this manual immediately.

This manual contains the private confidential information belonging to Shandong New Beiyang

Information Technology Co., Ltd. (hereinafter referred to as SNBC). You must keep its relative content as

the confidential information. If the users are commercial customers or entities, you should be aware to

disclose it to those people with the confidential responsibility including your employees, agencies and

partners. When you terminate the cooperation with SNBC or SNBC puts forward a request, you have to

stop using this manual and return it to SNBC, or destroy the confidential information.

If any relative organ such as court, arbitrator or government authority requests you to disclose any

confidential information of this manual, you must inform SNBC quickly and also agree that you shall

cooperate or assist with SNBC reasonably during the negotiation.

SNBC has the right to disclose its confidential information and does not be responsible for the loss or

damages caused from the wrong usage or reference of this manual by users.

Information in this document is subject to change without notice, which is only used for product

maintenance or service relative to this manual. SNBC reserves the right to modify the manual. If users

need further data about the products, please feel free to contact SNBC or your local dealer.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or

mechanical, for any purpose without the express written permission of SNBC.

Printed in China

Trademarks

SNBC registered trademarks:

Address: No.126 Kunlun Road, Huancui District, Weihai, Shandong, China.

Order Tel: +86-631-5671111

Technical support: +86-631-5675888 800861368

Fax: +86-631-5680499 5675111

PC: 264203

Website: www.newbeiyang.com

E-mail: [email protected]

BT-T080 Programming Manual

- 2 -

Content

1 Overview ...............................................................................................................................................1

1.1 Command Classification..............................................................................................................1

1.2 Key terms ....................................................................................................................................1

1.3 Command format.........................................................................................................................1

2 Command Description...........................................................................................................................3

2.1 Print command ............................................................................................................................3

LF Print and feed one line .......................................................................................................3

FF Print and feed paper...........................................................................................................3

CR Print and carriage return....................................................................................................3

ESC FF Print in page mode.....................................................................................................4

ESC J n Print and feed paper ..................................................................................................4

ESC d n Print and feed n lines.................................................................................................5

2.2 Location command ......................................................................................................................5

HT Horizontal tab.....................................................................................................................5

ESC $ nL Nh Set absolute horizontal printing position ............................................................6

ESC D n1...nk NUL Set horizontal tab positions ......................................................................7

ESC T n Select printing area direction in page mode ..............................................................7

ESC W xL xH yL yH dxL dxH dyL dyH Set printing area in page mode ...................................9

ESC \ nL nH Set relative horizontal printing position .............................................................11

ESC a n Select character align mode....................................................................................11

GS $ nL nH Sets the absolute vertical position in page mode ...............................................12

GS L nL nH Set left margin ....................................................................................................13

GS P x y Set the horizontal and vertical motion units ............................................................14

GS W nL nH Set printing area width ......................................................................................15

GS \ nL nH Set relative vertical print position in page mode..................................................16

GS T n Set print starting positon at the bigninning of line ......................................................16

2.3 Character command..................................................................................................................17

CAN Delete data in print buffer in page mode .......................................................................17

ESC SP n Set right-side character spacing ...........................................................................18

ESC ! n Select print mode .....................................................................................................18

BT-T080 Programming Manual

- 3 -

ESC % n Select/cancel user-defined character.....................................................................20

ESC & y c1 c2 [x1 d1...d(y × x1)]...[xk d1...d(y × xk)] Define user-defined character ............20

ESC – n Select/Cancel underline mode ................................................................................22

ESC ? n Cancel user-defined characters ..............................................................................23

ESC E n Select/Cancel bold mode ........................................................................................23

ESC G n Select/Cancel double-strike mode..........................................................................24

ESC M n Select character font ..............................................................................................24

ESC R n Select an international character set.......................................................................24

ESC V n Select/Cancel 90° clockwise rotation ......................................................................25

ESC t n Set code page ..........................................................................................................26

ESC { n Select/Cancel upside-down printing mode ...............................................................26

GS ! n Select character size ..................................................................................................27

GS B n Select/Cancel white/black reverse printing mode......................................................28

FS ! n Set Chinese character mode.......................................................................................29

FS & Select Chinese character mode....................................................................................29

FS – n Select/Cancel underline mode for Chinese characters ..............................................30

FS . Cancel Chinese character mode ..................................................................................30

FS 2 c1 c2 d1...dk Define user-defined Chinese characters..................................................31

FS S n1 n2 Set left-side and right-side Chinese character spacing.......................................32

FS W n Select/Cancel quadruple-size mode for Chinese characters ....................................32

2.4 Bitmap Command......................................................................................................................33

ESC * m nL nH d1... dk Select bitmap mode .........................................................................33

GS # n Define current RAM bitmap number ..........................................................................34

GS * x y d1...d(x × y × 8) Define downloaded bitmap ............................................................35

GS / m Print downloaded bitmap ...........................................................................................35

GS v 0 m xL xH yL yH d1....dk Print raster bitmap.................................................................36

FS p n m Print bitmap downloaded in NV memory ................................................................37

FS q n [xL xH yL yH d1...dk]1...[xL xH yL yH d1...dk]n Define NV bitmap..............................38

2.5 Status command........................................................................................................................40

DLE EOT n Real-time status transmission ............................................................................40

DLE ENQ n Real-time request...............................................................................................42

BT-T080 Programming Manual

- 4 -

GS r n Transmit status...........................................................................................................42

GS a n Set Automatic Status Back (ASB)..............................................................................43

2.6 Barcode command ....................................................................................................................45

GS H n Select printing position for Human Readable Interpretation (HRI) characters...........45

GS f n Select font for Human Readable Interpretation (HRI) characters..................................45

GS h n Select barcode height................................................................................................46

GS k m d1...dk NUL GS k m n d1...dn Print barcode①② ......................................................46

GS w n Set barcode width .....................................................................................................50

GS p n Set the size of PDF417 barcode ..................................................................................50

GS q n Set correction grade of PDF417 barcode.....................................................................51

2.7 Other commands.......................................................................................................................51

ESC 2 Set default line spacing ..............................................................................................51

ESC 3 n Set line spacing.......................................................................................................51

ESC @ Initialize printer .........................................................................................................51

ESC L Select page mode ......................................................................................................52

ESC S Select standard mode ................................................................................................52

ESC c 0 n Select paper type..................................................................................................53

ESC c 3 n Select paper sensor to output paper end signals..................................................53

ESC c 4 n Select paper sensor to stop printing .....................................................................54

ESC c 5 n Enable/disable buttons .........................................................................................54

GS FF Marked paper location................................................................................................54

GS ( A pL pH n m Execute test printing .................................................................................55

GS ( E pL pH m [parameter] User-defined function ...............................................................56

GS ( E pL pH m d1 d2 (m = 1) <Function 1>............................................................................57

GS ( E pL pH m d1 d2 d3 (m = 2) <Function 2>.......................................................................57

GS ( E pL pH m [a1 b18...b11]...[ak bk8...bk1] (m = 3) <Function 3>.......................................58

GS ( E pL pH m a (m = 4) <Function 4>...................................................................................58

GS ( F pL pH a m nL nH Set parameters of print starting position and cut position ...............59

GS ( K pL pH n m Set print darkness.....................................................................................60

GS ( M pL pH a n m Save or load the data defined by command GS ( F ..............................60

GS ( M pL pH n m ((n) = 1, 49) <Function 1>...........................................................................61

BT-T080 Programming Manual

- 5 -

GS ( M pL pH n m ((n) = 2, 50) <Function 2>...........................................................................61

GS ( M pL pH n m ((n) = 3, 51) < Function 3>..........................................................................62

GS : Start/end macro definition..............................................................................................62

GS C 0 n m Select count print mode ...........................................................................63

GS C 1 aL aH bL bH n r Select count mode (A) ....................................................................64

GS C 2 nL nH Set current count value...................................................................................64

GS C ; sa ; sb ; sn; sr; sc;Select count mode .......................................................................65

GS I n Inquire printer ID.........................................................................................................66

GS V m GS V m n Select cut mode and cut paper①② .........................................................67

GS ^ r t m Execute macro......................................................................................................67

GS c Print count value...........................................................................................................68

3 Programming instructions....................................................................................................................69

3.1 General information...................................................................................................................69

3.2 Programming examples ............................................................................................................69

3.2.1 Initialization .....................................................................................................................69

3.2.2 Set printing and print data (character /barcode/bitmap) ..................................................69

3.2.3 Print and cut paper..........................................................................................................71

3.2.4 Status check....................................................................................................................73

3.2.5 Bitmap download.............................................................................................................73

3.2.6 Recommendations on applicable flow for programm ......................................................76

Appendix ................................................................................................................................................77

Appendix A CODE128 .....................................................................................................................77

A.1 Overview of CODE128 ......................................................................................................77

A.2 Code set ............................................................................................................................77

Appendix B: Print mode and its change ..........................................................................................80

B.1 General description............................................................................................................80

B.2 Set values in standard and page modes............................................................................81

B.3 Set printing area ................................................................................................................81

BT-T080 Programming Manual

- 1 -

1 Overview

1.1 Command Classification

This printer commands are classified as below:

Print commands: used for printing and feeding paper;

Position commands: to control the print position;

Character commands: to set character property;

Bitmap commands: to download bitmap and print relative commands, including NV and RAM bitmap;

Status commands: used for printer status query;

Barcode commands: barcode print and property settings;

Other commands: used for periphery control, Macro-definition and initialization, etc.;

Command instruction refers to the detailed function of relative commands.

1.2 Key terms

Real-time commands: These commands are acted on immediately upon being received by the

printer (regardless the printer’s busy or error status).

Page mode: Under this mode, the printer possesses all data in specified memory and

thinks of this as a virtual page. The page is printed when the printer receives

print command either FF or ESC FF.

Standard mode: Standard mode is the default mode of printer uses to operate. Under this

mode, the printer prints data and feeds paper upon print line buffer full (data is

enough for one print line) or receiving print command like LF.

Marked paper mode: Configuration of printer is marked paper.

HRI Characters: Human readable interpretation of the barcode.

NV: Non-volatile memory in which data stored does not loss when power off.

RAM: Random Access Memory

Motion unit: The motion unit has vertical motion unit and horizontal motion unit, which

specify the least space for vertical motion and horizontal motion. The vertical

motion unit and horizontal motion unit are set by GS P command.

ASB: Auto status back

DPI: Print dots per inch (one inch equals to 25.4mm). It is used to identify the

resolution of a printer, e.g. 203DPI means 203 print dots per inch. DPI: Dot

Per Inch.

Font 0: A standard character, size is 12 x 24;

Font 1: Compressed character, size is 9 X 17;

1.3 Command format

[Function] ――The name and function summary of commands;

[Format] ――The format of command data, such as ASCII, Hex and Decimal;

[Value Range] ――The value range of parameter in the command;

BT-T080 Programming Manual

- 2 -

[Notes] ――Explain the main features and application notices of commands;

[Default] ――The initial value used after the printer initialized;

[Relative] ――Other commands related to current command;

[Example]――Example used for current or relative commands.

All command data in programming Demo use HEX. All normal font/characters are data. There is no

explanation for the data of command such as 42 43, which is data. The font/character underlined and

emphasized is a command such as 1B 40.All the data inside parentheses after all commands in Demo

is used to explain the meanings of this command. The parentheses and data inside it is not the

command to be transmitted to the printer.

BT-T080 Programming Manual

- 3 -

2 Command Description

2.1 Print command

LF Print and feed one line

[Function] Print the data in buffer and feed one line

[Format] ASCII LF

Hex 0A

Decimal 10

[Notes] This command sets the print position to the beginning of the line.

[Relative] ESC 2, ESC 3

FF Print and feed paper

[Function] Print and feed paper.

[Format] ASCII FF

Hex 0C

Decimal 12

[Notes] • In page mode:

Prints and clears the data in the print buffer, and returns to standard mode;

• In standard mode:

When select marked paper, prints data in the buffer and feeds paper for one line,

then printer feeds paper to the beginning of next print position.

• This command is invalid if continuous paper is selected.

• The buffer data is deleted after being printed.

• The print width set by command ESC W will recovery to the default value.

• This command sets the print position to the beginning of the line.

[Relative] ESC FF, ESC L, ESC S , GS ( F , GS FF

CR Print and carriage return

[Function] Print and carriage return.

[Format] ASCII CR

Hex 0D

Decimal 13

[Notes] • When the command is enabled, it equals to LF; the command is ignored when it is

disabled.

• Set the print position to the beginning of the line.

• The command is ignored under serial interface mode.

• The printer configuration specify whether the command to be ignored or not under

parallel interface.

[Relative] LF

BT-T080 Programming Manual

- 4 -

ESC FF Print in page mode

[Function] Print all the data in buffer in page mode.

[Format] ASCII ESC FF

Hex 1B 0C

Decimal 27 12

[Notes] • This command is enabled only in page mode.

• After printing, the printer does not clear the buffered data, setting values for ESC T

and ESC W, and the position for buffering character data.

[Relative] FF, ESC L, ESC S

ESC J n Print and feed paper

[Function] Print and feed paper.

[Format] ASCII ESC J n

Hex 1B 4A n

Decimal 27 74 n

[Value range] 0 ≤n ≤255

[Notes] • Prints the data in the print buffer and feeds pape of [ n × horizontal or vertical motion

unit] inch.

• After printing is completed, this command sets the print starting position to the

beginning of the line.

• The paper feed amount set by this command is not affected by the values set by ESC

2or ESC 3.

• In standard mode, the printer uses the vertical motion unit (y).

• In page mode, this command functions as follows, depending on the direction and

print starting position of the print area:

When the print starting position is set to the upper left or lower right of the printable①

area by ESC T, the vertical motion unit (y) is used.

When the star②ting position is set to the upper right or lower left of the printable area

by ESC T, the horizontal motion unit (x) is used.

• The maximum paper feed amount is 1016mm (40 inches). When the setting value

exceeds the maximum, it is converted to the maximum automatically.

• When the mark sensor is valid, the command is still valid if the setting value exceeds

the maximum value.

[Example] 1B 40(initialize printer)

1D 50 CB CB(set the resolution to 203×203)

41 41 41 41 41 41 41(data to be printed)

1B 4A 50(print and feed paper 80/203 inches)

42 42 42 42 42 42 42 0A(data to be printed)

Results:

Indice

Altri manuali SNBC Stampante

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente