Star Micronics SP317/347F Manuale utente
DOT MATRIX PRINTER
SP317/347F
INSTALLATION MANUAL
GUIDE D’INSTALLATION
AUFSTELLANLEITUNG
MANUALE DI INSTALLAZIONE
TABLE OF CONTENTS
1. UNPACKING AND INSTALLATION ................................................ 2
1-1. Unpacking .................................................................................... 2
1-2. Handling Notes ............................................................................ 2
2. PARTS IDENTIFICATION AND NOMENCLATURE ...................... 3
3. FERRITE CORE INSTALLATION ..................................................... 4
4. CONNECTING THE INTERFACE CABLE ....................................... 6
4-1. Serial Interface Cable ...................................................................6
4-2. Parallel Interface Cable ................................................................ 6
APPENDIX ............................................................................................. 25
– 2 –
1. UNPACKING AND INSTALLATION
1-1. Unpacking
After unpacking the unit, check that all the necessary accessories are included in
the package.
Fig. 1-1 Unpacking
1-2. Handling Notes
1. Install the unit on a stand or table which has a flat, even surface.
2. Do not connect the AC power plug to the same outlet used for other electrical
noise generating devices (such as an electrical motor, etc.)
IMPORTANT!
Install the printer near an easily accessible socket-outlet.
3. Be careful not to drop paper clips, pins or other foreign objects into the unit
as these could cause the printer to malfunction.
4. When cleaning the outer surface of the unit, wipe away dirt, foreign matter,
etc., with a soft cloth, soaked in a neutral detergent.
5. Do not attempt to print when the paper or ribbon cartridge are not loaded in
the printer as this could damage the print head.
6. Use only roll paper that is not glued to the core.
7. Do not open the front cover while printing (this is interpreted as a mechanical
error and the printer will stop).
Ferrite cores
*1
Fasteners
*1
*1: The number of ferrite
cores and fasteners
differs according to
the area and type of
interface.
– 3 –
ENGLISH
2. PARTS IDENTIFICATION AND NOMENCLATURE
Fig. 2-1 External view of the printer
– 4 –
3. FERRITE CORE INSTALLATION
Ferrite core
Interface cable
10cm
maximum
Fastener
NOTE: Take special care when following the procedures listed below.
■A ferrite core is necessary on the printer interface cable to prevent the
generation of noise. If a parallel interface cable is used, a ferrite core must be
installed on the cable. If a serial intserface cable is used, a ferrite core must be
installed on the cable for all areas, except the US and Hong Kong.
■The ferrite core is normally packed so it is open, as shown in Fig 3-2. If you
find that a ferrite core is not open, use a pointed object to pry the plastic lock
of the ferrite core apart (Fig 3-1). When you do, take care not to damage the
ferrite core or the plastic lock.
Pass fastener through ferrite core.
Fig. 3-3
Fig. 3-1
Fig. 3-2
Pull and cu
t
Pass fastener around cable and lock it.
Cut off excess with scissors.
Fig. 3-4
–5 –
ENGLISH
To install the interface cable ferrite core
■Clamp the ferrite core onto the interface cable as shown in Fig 3-2.
Take care to avoid damaging the interface cable when installing the ferrite
core. The ferrite core should be anchored firmly in place with the fastener that
comes with it, as shown in Fig 3-3 and 3-4.
Fig. 3-5
To install the cash drawer drive cable ferrite core (except for
US, HK)
■Clamp the ferrite core onto the cash drawer drive cable, looping the cable as
shown in Fig. 3-2.
•When installing the ferrite core be careful not to damage the cable.
•The ferrite core should be anchored firmly in place with the fastener that
comes with it, as shown in Fig. 3-3 and Fig. 3-4.
•Do not forget to loop the cable.
Separate ground wire re-
quired except for US, HK.
Ferrite core
(except for US, HK)
–6 –
4-1. Serial Interface Cable
4. CONNECTING THE INTERFACE CABLE
1Turn off power for both the host
computer and the printer.
2Insert the connector of the interface
cable into the connector on the
printer and the other end of the in-
terface cable into the connector for
the host computer.
3Next, tighten the screws on the con-
nectors.
Fig. 4-1 Connecting the serial interface
cable
4-2. Parallel Interface Cable
Screws
Screwdriver
Fig. 4-2 Connecting the parallel interface
cable
1Turn off the power for both the host
computer and the printer.
2Insertone connector of the interface
cable into the printer’s connector
andfastenitwiththeclasp,asshown
in Fig. 4-2.
3Inserttheotherterminal of the inter-
face cable into the host computer’s
connector, and fasten it with the
clasp.
TABLE DES MATIÈRES
1. DÉBALLAGE ET INSTALLATION ................................................... 8
1-1. Déballage ..................................................................................... 8
1-2. Remarques concernant la manipulation ....................................... 8
2. IDENTIFICATION DES PIÈCES ET NOMENCLATURE ................ 9
3. INSTALLATION DU NOYAU EN FERRITE .................................. 10
4. CONNEXION DU CÂBLE D’INTERFACE ..................................... 12
4-1. Câble d’interface sériel .............................................................. 12
4-2. Câble d’interface parallèle ......................................................... 12
APPENDICE ........................................................................................... 25
L’appendice n’est pas traduit.
–8 –
1. DÉBALLAGE ET INSTALLATION
1-1. Déballage
Après avoir déballél’appareil, vérifiez si vous disposez bien de tous les accessoi-
res illustrés ci-après.
Fig. 1-1 Déballage
1-2. Remarques concernant la manipulation
1. Installez l’appareil sur un support ou sur une table dont la surface est plate et
uniforme.
2. Ne branchez pas l’appareil àla même prise secteur que d’autres appareils
produisant des bruits électriques (appareils ayant un moteur électrique, etc.).
IMPORTANT !
Installez l’imprimante le plus près possible d’une prise secteur facilement
accessible.
3. Veillez àne pas laisser tomber des trombones, punaises ou autres objets dans
l’appareil, cela risque de causer un mauvais fonctionnement.
4. Nettoyez la surface de l’imprimante àl’aide d’un chiffon doux humidifiéet
d’un détergent neutre.
5. Ne lancez pas l’impression si le papier ou la cartouche de ruban ne sont pas
installés, sous peine d’endommager la tête d’impression.
6. N’utilisez jamais un rouleau de papier dont l’extrémitéest collée au rouleau
central.
7. N’ouvrez pas le cache avant de l’appareil pendant l’impression ; en effet cela
serait interprétécomme étant une erreur mécanique et l’impression s’inter-
romprait automatiquement.
Imprimante
Attaches pour rouleau de papier (2)
Axe pour rouleau de
papier
Anneaux d’arrêt (2)
Noyau en ferrite
*1
Attache
*1
Cartouche de ruban
Guide d’utilisation
Guide d’installation
*1 Le nombre de tores
de ferrite et de
fixations dépend de
la région et du type
d’interface.
Questo manuale è adatto per i seguenti modelli
2
Indice
Lingue:
Altri manuali Star Micronics Stampante
Star Micronics
Star Micronics TSP100LAN Manuale utente
Star Micronics
Star Micronics LC24-200 Colour Manuale utente
Star Micronics
Star Micronics Rainbow NX-1000C Manuale utente
Star Micronics
Star Micronics SM-T300I SERIES Manuale utente
Star Micronics
Star Micronics SP500 Series Manuale utente
Star Micronics
Star Micronics SR-10/I5 Manuale utente
Star Micronics
Star Micronics NP-226 Istruzioni per l'installazione
Star Micronics
Star Micronics LC-90 Manuale utente
Star Micronics
Star Micronics NX-1000 Manuale utente
Star Micronics
Star Micronics WinType 4000 Manuale utente
Star Micronics
Star Micronics Multi-Font NX-2410 Manuale utente
Star Micronics
Star Micronics TUP500 series Istruzioni per l'installazione
Star Micronics
Star Micronics MP100 Manuale
Star Micronics
Star Micronics XB24-200 Manuale utente
Star Micronics
Star Micronics LC-8021 Manuale utente
Star Micronics
Star Micronics Delta Manuale utente
Star Micronics
Star Micronics LC24-15 Manuale utente
Star Micronics
Star Micronics SP349 Manuale utente
Star Micronics
Star Micronics TSP1000 Series Manuale utente
Star Micronics
Star Micronics LC-8211 Manuale utente
