Star Micronics TSP212 Manuale utente

THERMAL PRINTER

TSP200 SERIES

USERS MANUAL

GUIDE D’UTILISATION

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

NOTICE

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

TABLE OF CONTENTS

1. SETTING THE PAPER ......................................................................1

1-1. Setting the Paper ..........................................................................1

1-2. Changing the Paper ......................................................................3

1-3. Paper Jams....................................................................................4

2. CONTROL PANEL ............................................................................5

2-1. Power ON.....................................................................................5

2-2. Errors............................................................................................6

3. CAUTIONS.........................................................................................7

3-1. Operating Cautions ......................................................................7

3-2. Safety Cautions ............................................................................7

4. COMMAND SUMMARY ..................................................................8

4-1. Star Mode.....................................................................................8

4-2. ESC/POS Mode*........................................................................12

APPENDIX .............................................................................................56

* ESC/POS is a trademark of Seiko Epson Corporation.

– 1 –

ENGLISH

1Open the cover.

2If the unit has an auto-cutter unit,

move the unit in the direction of the

arrow until the lock engages. (This

step is unnecessary if there is no

auto-cutter unit.)

3Widenthepaper holderinthe direc-

tion of the arrow and position the

paper in the manner shown in the

illustration. Make sure that the core

of the paper is firmly held by the

paper holder at this time.

1-1. Setting the Paper

Prepare a roll of paper. Make sure that the feeding edge of the paper is cut in a

straight right angle to the direction of feed.

Roll paper

Core

Axis

Paper roll holder

1. SETTING THE PAPER

– 2 –

ENGLISH

4Auto Loading

Insert the edge of the paper into the

opening. The paper is properly in-

sertedwhen paper extends from the

printer mechanism. Check that the

paper is protruding approximately

15 to 20 centimeters from printer

mechanism. If the paper extends

less than 15 centimeters, press the

feed key to feed more paper. Once

thesestepshavebeentaken,remove

any remaining slack in the paper.

If the paper has not been inserted

straight, it will jam. If this happens,

pull the head up lever towards you

and pull on the edge of the paper

until the paper is moving straight.

After confirming that 15 to 20

centimeters of paper is extending

from the printer, push the head up

lever back to the previous position.

Manual Loading

Pull the head up lever forward to

bring the print head into the up po-

sition. Insert the edge of the paper

into the opening and turn the green

knob located near the head up lever

untiltheedgeofthepaperprotrudes

from the printer mechanism. Grab

the edge of the paper and pull the

paper until it is moving straight.

After confirming that 15 to 20

centimeters of paper is extending

from the printer, push the head up

lever back to the previous position.

– 3 –

ENGLISH

5Holdtheedgeofthepaperandpress

it against the head and cut it. Be

careful not to cut your hands or

fingers on the edge of the auto-

cutter unit.

6Closetheauto-cutterunit.(Thisstep

is unnecessary if there is no auto-

cutter unit.)

7Close the cover and press the on-

line switch. The on-line lamp will

come on.

1If the near-end sensor is operating

and there is still paper on the roll,

cut the paper just before the paper

opening and then press the (feed)

switch until the feed of paper stops.

2Openthecoverand pullthehead up

lever forward so the print head is in

the up position and pull the paper

out.

3Widenthepaperholderinthedirec-

tion of the arrow and remove paper

roll or the core.

4Follow the procedure outlined in

“1-1 Setting the Paper” to replace

the paper roll.

1-2. Changing the Paper

– 4 –

ENGLISH

1-3. Paper Jams

1Turn the power off and open the cover.

2If the unit has an auto-cutter unit, move the unit in the direction of the arrow

untilthelockengages.(Thisstepisunnecessaryifthereisnoauto-cutterunit.)

3Cut the roll of paper just before the paper opening and remove the paper.

4Using the same procedure outlined for cleaning the head, push the head open

lever back to release the set cover system and to place the head in the open

position.

5Remove the paper jam. If the jam cannot be removed, turn the feed knob and

remove the paper.

6Oncethepaperjamhasbeenremoved,pressthetopofthesetcoverandengage

the head open lever.

Caution

If the paper jam is in the auto-cutter, insert a Phillips screwdriver into the right

side of the auto-cutter and use it to turn the internal gears to free the paper jam.

– 5 –

ENGLISH

2-1. Power ON

Operating Panel

Paper - Yes

Paper - No

1Power Lamp (Green LED)

2On-Line Lamp (Green LED)

3On-Line Switch

4Feed Switch

When the power switch is turned on, the Power Lamp and On-Line Lamp will

come on. If there is no paper, the Power Lamp will flash at approximately one

second intervals.

ON LINE

POWER FEED

ON LINE

POWER FEED

12 3 4

2. CONTROL PANEL

– 6 –

ENGLISH

2-2. Errors

1) Automatic Recovery (Power Lamp: Flashing; On-Line Lamp: On)

Error Description

Abnormal head

temperature

Power Lamp Flashing Pattern Recovery Conditions

Automatic recovery after head

temperature lowers.

2) Recoverable Errors (Power Lamp: Flashing; On-Line Lamp: Off)

Power Lamp Flashing Pattern Recovery Conditions

Insert paper and press on-line

switch. (Star)

Insert paper and close cover. (ESC/

POS)

Lower head and press on-line

switch. (Star)

Lower head and close cover. (ESC/

POS)

Press on-line switch and printing

will continue. Both lamps light

when printing and power lamp

flashes and on-line lamp lights

when on-line. (Star)

Same as “No paper”. (ESC/POS)

Close cover and press on-line

switch. (Star)

Close cover. (ESC/POS)

If the blade is at the home position,

press on-line switch to continue

printing. If the blade is not at the

home position, it is not a recover-

able error. (Star)

Command (ESC/POS)

Approx. 1 Sec Approx. 1 Sec

Approx. 250 msApprox. 250 ms

Approx. 2 Sec Approx. 2 Sec

Approx.

500 ms Approx.

500 ms

Approx. 125 msApprox. 125 ms

Error Description

No paper

Head up

Paper near end of

roll

Cover is open

Error during paper

cutting

3) Fatal Error (Power Lamp: Flashing; On-Line Lamp: Flashing) the unit

will have to be repaired.

– 7 –

ENGLISH

3-1. Operating Cautions

1The service life of the thermal print head cannot be guaranteed if any paper

other than the recommended paper is used. There will be a noticeable decline

intheservicelifeofthethermalelementoftheprintheadwhenthepaperused

contains (Na+, K++, CI-).

2Never print when there is water or any form of moisture, such as from

condensation, on the surface of the print head.

3-2. Safety Cautions

1Never touch the thermal print head or motor during printing or immediately

after printing as these components are very hot.

2Never touch any moving parts, such as gears or knobs, during printing.

3Always use care near the edges of printer components, especially metal

components, as they may cause injury.

3. CAUTIONS

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Star Micronics Stampante

Star Micronics

Star Micronics SP 200 Manuale utente

Star Micronics

Star Micronics TSP400 Series Manuale utente

Star Micronics

Star Micronics mC-Print3 MCP31L Guida rapida

Star Micronics

Star Micronics FR-10 Manuale utente

Star Micronics

Star Micronics WinType 4000 Manuale utente

Star Micronics

Star Micronics NX-1020 Manuale utente

Star Micronics

Star Micronics LC-1021 Manuale utente

Star Micronics

Star Micronics LC-8021 Manuale utente

Star Micronics

Star Micronics NX-1000 Manuale utente

Star Micronics

Star Micronics NX-2400 Manuale utente

Star Micronics

Star Micronics LC-6211 Manuale utente

Star Micronics

Star Micronics Star SCP700 Series Manuale utente

Star Micronics

Star Micronics LC-7211 Manuale utente

Star Micronics

Star Micronics TSP650II SERIES Manuale utente

Star Micronics

Star Micronics MULTI-FONT NX-1000II Manuale utente

Star Micronics

Star Micronics SP312F Manuale utente

Star Micronics

Star Micronics LC24-15 Manuale utente

Star Micronics

Star Micronics SP500 Series Manuale utente

Star Micronics

Star Micronics SM-S230I Series Manuale utente

Star Micronics

Star Micronics TCP300II Series Istruzioni per l'installazione

Star Micronics

Star Micronics LC-200 Manuale utente

Star Micronics

Star Micronics TSP200 Series Manuale utente

Star Micronics

Star Micronics SP717 Series Manuale utente

Star Micronics

Star Micronics DP8340R Series Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente