Stratasys Objet Series Guida

Caution—

To avoid exposure to skin irritants,

wear protective gloves (provided)

throughout this procedure.

DOC-34032 Rev. A

B. Remove screws B.

C. Loosen screw C.

A. Put on protective gloves. Remove the print block cover.

A. Remove the Support print head card.

B. Loosen the print head thumb screws.

Removing the Support Print Head

Support Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 1

While holding the print head, press down

on the thumb screws and remove it.

DOC-34032 Rev. A

5Make sure you remove the two O-ring

seals along with the print head.

6Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Install the print block cover.

Push on the tab and then pull the jig

downwards to remove it.

DOC-34032 Page 2

Rev. A

Tighten the print head thumb screws.

Press down firmly on the Support print

head card to attach it to the print block.

Installing the Support Print Head

FRONT

PUSH

FIRST

With the print head in the positioning jig,

align it as shown.

Make sure the O-ring seals

are installed on the print head.

FRONT

Remove

Push tab

A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

A. Insert and tighten screws A.

B. Tighten screw B.

Make sure that the Model head is installed as described in Model Print Head Replacement.

Remove the Model print head card.

Removing the Model Print Head

Model Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 3

B. Loosen the print head thumb screws.

DOC-34032 Rev. A

Make sure you remove the two O-ring

seals along with the print head.

2While holding the print head, press down

on the thumb screws and remove it.

To replace the Model print head, you must first remove the Support print head

(see page 1).

Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Installing the Model Print Head

Page 4

DOC-34032 Rev. A

After you replace the Model print-head, re-install the Support head (see page 2).

Push on the tab and then pull the jig

downwards to remove it.

Tighten the print head thumb screws.

Press down firmly on the Model print

head card to attach it to the print block.

FRONT

PUSH

FIRST

Make sure the O-ring seals

are installed on the print head.

FRONT

With the print head in the positioning jig,

align it as shown.

3A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

FRONT

Remove

Push tab

Altri manuali Stratasys Stampante 3D

Stratasys

Stratasys Fortus 360mc Manuale utente

Stratasys

Stratasys Dimension 768/Elite Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

Stratasys

Stratasys J750 Manuale utente

Stratasys

Stratasys 180-00108 uPrint Manuale utente

Stratasys

Stratasys Objet30 Manuale utente

Stratasys

Stratasys J826 Istruzioni operative

Stratasys

Stratasys Mojo Manuale utente

Stratasys

Stratasys V650 Flex Manuale utente

Stratasys

Stratasys Eden350V Manuale utente

Stratasys

Stratasys Objet1000 Connex 2 Manuale utente

Stratasys

Stratasys F123 Series Istruzioni operative

Stratasys

Stratasys Objet24 Guida all'installazione

Stratasys

Stratasys Eden260V Manuale utente

Stratasys

Stratasys F900 Manuale utente

Stratasys

Stratasys J750 Manuale utente

Stratasys

Stratasys J4100 Manuale utente

Stratasys

Stratasys F120 Istruzioni operative

Stratasys

Stratasys Dimension Elite Manuale utente

Stratasys

Stratasys Fortus 900mc Guida di riferimento

Stratasys

Stratasys Origin One Manuale utente

Stratasys

Stratasys Objet350 Manuale utente

Stratasys

Stratasys Objet500 Manuale utente

Stratasys

Stratasys F123 Series Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

MakerBot

MakerBot Replicator Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente

LONGER

LONGER LK4 Pro Manuale utente

German RepRap

German RepRap X400 Pro V3 Manuale utente