TRENDnet TPE-S44 - Switch Manuale utente
TPE-S44
Quick Installation Guide
Table of Contents
English ......................................................................................................
Technical Specifications ............................................
Troubleshooting ........................................................................................
................ ................
1
1
6
3
8
10
1. Before You Start
......................................................
3. Hardware Installation ........................................................................
................................................................................
2. Identifying External Components
Table of Contents
Version 01.19.2007
System Requirements
TPE-S44
Quick Installation Guide
Power cord
Rubber Feet
Computer with Network adapter installed
RJ-45 Network Cable
The surface must support at least 1.5 Kg for the Switch
The power outlet should be within 1.82 meters (6 feet) of the Switch
Package Contents
1. Before You Start
English
1
Note: The TPE-S44 only supports Powered Devices that follow the IEEE
802.3af Mode A (pin 1, 2, 3, 6) standard
AC Power Adapter (48V DC,
0.8A)
Do not place heavy objects on the Switch
IEEE 802.3af Powered Device
TPE-102S (Optional)
Visually inspect the DC power jack to make sure that it is securely
connected to the power adapter
Make sure that there is proper heat dissipation and adequate
ventilation around the Switch
Application
English
2
10/100Mbps
10/100Mbps + PoE
8-Port 10/100Mbps
Fast Ethernet PoE Switch
(TPE-S44)
Advanced Wireless Pan & Tilt
Internet Camera Server
(TV-IP400W)
Power over Ethernet
(PoE) Splitter
(TPE-102S)
Power over Ethernet
(PoE) Splitter
(TPE-102S)
108Mbps 802.11g
Wireless Access Point
(TEW-450APB)
108Mbps 802.11g
Hot-Spot Access Point
(TEW-453APB)
54Mbps 802.11g Wireless
PoE Access Point
(TEW-434APB)
2. Identifying External Components
English
3
Front Panel
This section identifies all the major external components of the Switch. Both
the front and rear panels are shown with descriptions of each feature.
Note: When you power on the Switch, all LEDs will turn ON for about 1 second and
then turn OFF. Only the Power LED will stay lit.
PoE MAX
If the Switch detects there is
7.5W of power or less available,
this LED will light up. This
indicates a power overload. If
the Switch detects there is more
than 7.5W of power available,
the LED will not light up.
PoE Status (Ports 1~4)
When the Switch is connected
to a PoE device and the port
supplies power successfully, the
LED is green. When the LED is
red, the port has failed to
provide power. When there is
no Powered Device connected,
the LED is not lit.
Front Panel
System Power
When the LED is lit, the Switch
is receiving power.
100Mbps (Ports 1~8)
When the LED is lit, the port is
connected to an active Fast
Ethernet device. When the LED
is not lit, the port is either
connected to an Ethernet
connection or there is no
connection to the port.
Link/Act (Ports 1~8)
When the LED is lit, the port is
connected to an active
Ethernet/Fast Ethernet device. It
blinks green when the port is
transmitting or receiving data.
English
4
English
5
Rear Panel
DC Power Jack
Power is supplied through an
external AC power adapter.
Check the technical
specification section for
information about the DC power
input voltage. Since the Switch
does not include a power on/off
switch, plugging its power
adapter into a power outlet will
immediately power on the
Switch.
Ethernet Ports (5~8)
When the LED is lit green, the
Switch is receiving power.
PoE Ports (1~4)
The PoE port will be
automatically activated when a
compatible device is detected.
The Switch will supply power
through the Ethernet port to the
connected Powered Device.
English
6
Note: The maximum amount of power available is 15.4 Watts per port and 30
Watts total. If a power overload has occurred, the Switch will prioritize the
distribution of power by port (from lowest to highest). That is, port 1 will receive
the highest priority and port 4 will receive the lowest priority. The ports with
lower priority will have their PoE function disabled until more than 7.5 watts of
power becomes available.
3. Hardware Installation
1. Plug the power cord into the AC
Power Adapter. Connect the AC
Power Adapter to the TPE-S44
and then to a power outlet.
2. Connect a RJ-45 network cable
from the computer to an available
Ethernet port on the TPE-S44.
3. Connect a RJ-45 cable from a PoE
port (1~4) on the TPE-S44 to the
LAN port of the PoE device (e.g.
TEW-434APB)
4. Verify that the following panel lights
are on: System Power, PoE
Status and Link/ACT.
English
7
5. Verify that the following panel lights
are on: System Power, PoE
Status and Link/ACT.
Using a non-PoE device with the TPE-S44 and
the TPE-102S
2. Connect an Ethernet cable from a
PoE port (1~4) on the TPE-S44
switch to the POE IN port on the
TPE-102S.
3. Connect an Ethernet cable from a
non-PoE device to the DATA OUT
port on the TPE-102S.
4. Connect the provided Jumper
cable to a non-PoE device (e.g.
TV-IP100) and to the TPE-102S.
1. Select the proper voltage (5V or
12V).
8
Technical Specifications
General
Standards
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
ANSI/IEEE 802.3 NWay Auto-negotiation
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3af Power over Ethernet
Protocol CSMA/CD
Data Transfer Rates
Ethernet:
10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet:
100Mbps (half-duplex), 200Mbps (full-duplex)
Network Cables
Ethernet:
UTP/STP CAT-3, -4, -5 ; up to 100M
Fast Ethernet:
UTP/STP CAT-5, -5e, -6; up to 100M
Number of Ports
PoE Power on RJ-45
LED
4 × 10/100Mbps Auto-MDIX RJ45 ports with
PoE enabled (port 1 ~ port 4)
4 × 10/100Mbps Auto-MDIX RJ45 ports
(port 5 ~ port 8)
Power+: pin 3 & pin 6
Power-: pin 1 & pin 2
Per Unit: System Power; PoE Max
Per 10/100 Port: Link/ACT, 100
Per PoE Port: PoE Status, Link/ACT, 100
Topology Star
Altri manuali per TPE-S44 - Switch
5
Indice
Altri manuali TRENDnet Interruttore
TRENDnet
TRENDnet TEG-S5 Manuale utente
TRENDnet
TRENDnet GREENnet TEG-S24g Manuale utente
TRENDnet
TRENDnet TEG-240WS Manuale utente
TRENDnet
TRENDnet TK-800R Manuale utente
TRENDnet
TRENDnet TE100-S50g Manuale utente
TRENDnet
TRENDnet TEG-S50G Manuale utente
TRENDnet
TRENDnet TE100-SK4 Manuale utente
TRENDnet
TRENDnet TEG-S28TX Manuale utente
TRENDnet
TRENDnet TU2-400 Manuale utente
TRENDnet
TRENDnet TE-800 Manuale utente
TRENDnet
TRENDnet TE100-S16V Manuale utente
TRENDnet
TRENDnet TEG-S2400I - DATA SHEETS Manuale utente
TRENDnet
TRENDnet TK-409K Manuale utente
TRENDnet
TRENDnet TPE-80WS - Web Smart PoE Switch Manuale utente
TRENDnet
TRENDnet TK-IP101 Manuale utente
TRENDnet
TRENDnet TEG-448WS - Switch Manuale utente
TRENDnet
TRENDnet TE100-SK2 Manuale utente
TRENDnet
TRENDnet TPE-S44 - Switch Manuale utente
TRENDnet
TRENDnet TE100-S24V Manuale utente
TRENDnet
TRENDnet TK-408K Manuale utente
