Triplett PR600 Manuale utente
User Manual
PR600
Non-Contact Phase Sequence
Detector
INDEX PAGE
1. INTRODUCTION..............................
2. SAFETY NOTES...............................
3. FEATURES.......................................
4. SPECIFICATIONS............................
5. INSTRUMENT LAYOUT....................
6. MEASUREMENT..............................
7. LIVE WIRE CHECK..........................
8. MAINTENANCE................................
1
2-3
4
5
6-7
8-9
10
11-12
Due to our policy of conant improvement and development,
we reserve the right to change specications without notice.
-1-
1. INTRODUCTION
This Non-Contact PHASE DETECTOR has been
designed and tested According to CE Safety
Requirements for Electronic Measuring Apparatus,
IEC/EN 61010-1 and other safety standards. Follow
all warnings to ensure safe operation.
WARNING
READ "SAFETY NOTES" (NEXT PAGE) BEFORE
USING THE NON-CONTACT DETECTOR.
CAT IV - Measurements performed at the source of
the low voltage installation.
CAT III - Measurements performed in the building
installation.
CAT II - Measurement performed on circuits directly
connected to the low voltage installation.
-2-
2. SAFETY NOTES
1. Read the following safety information carefully
before attempting to operate or service the
detector.
2. Use the detector only as specied in this manual.
Otherwise, the protection provided by the detector
may be impaired.
3. This instrument cannot nd the missing line of
earth line (S line).
4. Do not touch the clips during measurements to get
accurate results.
5. Do not pull the cable when removing the
measurement clips from the measured conductors.
It may damage the cable.
6. Do not expose the instrument to direct sunlight,
high temperature, humidity, or moisture.
7. Do not use the instrument while it is wet. Keep dry!
8. Never open battery compartment cover while live
detecting.
9. Subjecting the detection to shock, vibration and
dropping......may damage the instrument.
10. Rated environmental conditions :
(1) Indoor AC1000V Max. Outdoor AC 600V Max.
(2) Installation Category Ⅲ.
(3) Pollution Degree 2.
(4) Altitude up to 2000 meters.
(5) Relative humidity 80% max.
-3-
(6) Ambient temperature 0~40℃.
11. Observe the International Electrical Symbols listed
below:
Detector is protected throughout by double
insulation or reinforced insulation.
Warning ! Risk of electric shock.
Caution ! Refer to this manual before using
the detector.
AC.....Alternating current.
~
-4-
3. FEATURES
●Protection class: IP40
●895 PR is a phase detector with LED display lights
and beeping buzzer to inform the detection of AC
3-phase sequence.
●Two functions in one unit: open phase and phase
sequence.
● Auto-o. (5 min Approx.)
●Clipping the right 3-phase lines (up to color) over
the jacket with non-contact sensor clips which
promotes safety during measurement.
●Bright button feature is convenient to make the
indication visible in dimly areas or sun light.
●Back cover magnet feature mounts the
instrument onto a AC distribution panel oer easy
measurement.
● 3-Phase AC 75 to 1000V is tted for detection.
●Detect frequency range is from 45 to 65 Hz.
●Safety standard:
EN 61010-1 CAT III 1000V / CAT IV 600V
EN 61326-1
-5-
4. SPECIFICATIONS
Measurement Principle Static induction
Input Voltage 75~1000Vac
Frequency Range 45-65Hz
Auto-O 5 min. after power on without
detection
Low Battery Warning Power LED ashes at
7.0±0.2V or less
Current consumption 20mA
Operating Temperature
& Humidity -10ºC~50ºC Max. 80% R.H.
Storage temperature
& Humidity -20ºC~60ºC Max. 80% R.H.
Power Source 9V x 1 alkaline battery
Dimensions 128 (L) x 72 (W) x 46 (H)mm
Cable Length Approx. 59" (1.5m)
Max conductor
diameter Approx. 1.3" (33mm)
Weight
(battery included) Approx. 375g
Accessories
Instruction manual
Soft case
Battery
-6-
5. INSTRUMENT LAYOUT
R S T
ON/OFF
BRIGHTER
PR600
CCW CW BAT.
OK
IP40
Non-Contact Phase
Sequence Detector
Buzzer
Battery LED
Power Button
Phase sequence
LEDs
Brightness Button
Open phase
indicator
-7-
Magnets for mounting is equipped on the back of this
product allow for hands-free use.
Magnet
Magnet
Warning label
Battery cover
-8-
BLUE
WHITE
R,L1
S,L2
T,L3
RED
6. MEASUREMENT
Before proceeding with measurement, read the safety
notes.
1. Press the power button to turn on the instrument.
All of the LEDS will ash during the 2 seconds. Only
the power LED stays on at the self demonstration
later.
Do not use the instrument when any of the LEDs
do not work.
2. Apex of "▼" mark on each measurement clip hold
on the center of each measurement conductor.
Connect three clips as shown:
Red to L1, Phase-R. White to L2, Phase-S.
Blue to L3, Phase-T.
Indice
Altri manuali Triplett Strumento di misura
Triplett
Triplett GSM250 Manuale utente
Triplett
Triplett BR500 Manuale utente
Triplett
Triplett ET400 Manuale utente
Triplett
Triplett AM320 Manuale utente
Triplett
Triplett CM450-NIST Manuale utente
Triplett
Triplett RHT45 Manuale utente
Triplett
Triplett 9200-A Manuale utente
Triplett
Triplett CTX690 Manuale utente
Triplett
Triplett RHT05 Manuale utente
Triplett
Triplett GSM120 Manuale utente
Triplett
Triplett AM320-NIST Manuale utente
Triplett
Triplett TA150 Manuale utente
Triplett
Triplett CM200 Manuale utente
Triplett
Triplett RHT22 Manuale utente
Triplett
Triplett 630 Manuale utente
Triplett
Triplett CM600 Manuale utente
Triplett
Triplett RHT01 Manuale utente
Triplett
Triplett PR400 Manuale utente
Triplett
Triplett FOX Manuale utente
Triplett
Triplett AM250 Manuale utente
