Ultimaker S3 Guida all'installazione

Ultimaker S3 Ultimaker 2+ Connect

Basic instructions for 3D printing using:

What you need to bring:

Laptop USB

and / or

Cura software If your file needs support material, we recommend using

an S3 printer, which can use dissolvable PVA support. If

no support is required, we recommend using a 2+

Connect printer. But either type of printer can be used.

Orientate your file to eliminate or minimise the support

material required.

The material / nozzle settings should be set to:

or the ‘generic’, non-branded version of the material.

The nozzle used for providing support material on an S3

can be adjusted from the ‘support’ drop down in custom

settings. The printers are set up for Fine -0.1mm layer

height only. Overall, we recommend using the standard

settings for Fine -0.1mm. The infill can be set as desired,

but should be between 5% and 15%. A brim can be

replaced with a skirt in most cases where the model is

unlikely to fall over.

For these printers we recommend using Cura as the

slicing software. Export your model from your CAD

software as an STL, 3MF, or OBJ file.

Watch this Cura beginner’s tutorial:

www.youtube.com/watch?v=NsGOoi3677M

A –Check spool(s) are clear of obstructions and fed

into the feeders.

B –Check clamp(s) are in a down position on feeders.

C –Switch on the printer, and wait until ‘ready to print’

appears on the touch screen.

Do not attempt any maintenance or material changes.

Report these issues.

2Leave a note with your name and student email address

next to the machine, so you can be contacted if necessary.

A –Check that the glass bed is secured and clear of debris

(if not clean see step 4B). The bed is fully secured if the

clips close parallel with the glass bed.

B –Apply a light, single layer of glue to the bed, only on

areas where you have placed models in the slicing

software. Glue is found in the box above each printer.

C –Put your .ufp or equivalent gcode file onto a personal

USB or the printer’s USB. Plug this into the port left side

of the touch screen. Press ‘select from USB’.

Do not change any settings or attempt to perform

maintenance from the touch screen menu. Report issues.

3A –Select your file from the list. Scroll to page 2 once the

file is selected to see and check an image of the file. Select

Print. If a material change warning displays, as long as the

materials set in the slicing software match up closely with

those on the printer, it is fine to select ‘print anyway’.

B –Wait at the machine until your file begins to print, in

order to notice any issues that arise during the printer’s

start up procedure. This takes a few minutes. Caution: the

bed and nozzles warm up and become hot to touch during

printing.

C –Note the time it will take to print the file. Return as

soon as possible after the file has been printed. This will

make it easier to remove the printed models from the glass

bed, and frees up the printers for others to use. If you have

used the printer’s USB, clear your file off the stick.

If there is a problem during printing, ‘pause’ or ‘abort’

buttons can be selected. Follow on screen instruction to

complete the chosen procedure.

A –When the print is complete, carefully remove the

glass bed from the printer. Peel away the model from the

bed, or carefully use a provided scraper to assist. Do not

excessively finish or remove build material from your

model in the lab –take your model away and do this

elsewhere.

B –Use a scraper / glass cleaner / paper provided to

clean the bed of glue and build material. Do not spray

cleaner on the bed while it’s inside the printer. When

clean, return the bed to the printer. Clean away all mess

into the bin. The printer and surrounding area should be

left in the same condition as you hopefully found it.

C –Follow the onscreen instructions until the printer is

returned to its ‘ready to print’ screen. Turn off the printer

using the switch on the back.

If your model was printed on an S3 printer, the support

material, Natural PVA, can be removed either by

breaking it away, or sitting the model in warm water until

dissolved, or softened enough to be easily removed.

Altri manuali per S3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ultimaker Stampante 3D

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker 3 Extended Manuale utente

Ultimaker

Ultimaker 3 Extended Guida all'installazione

Ultimaker

Ultimaker Heated Bed Upgrade Kit Manuale utente

Ultimaker

Ultimaker Original Manuale utente

Ultimaker

Ultimaker Original Manuale utente

Ultimaker

Ultimaker ORIGINAL+ Manuale utente

Ultimaker

Ultimaker S3 Manuale utente

Ultimaker

Ultimaker 3 Extended Guida

Ultimaker

Ultimaker 2 Extended Manuale operativo e di manutenzione

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuale utente

Ultimaker

Ultimaker S3 Manuale utente

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker 3 Extended Istruzioni operative

Ultimaker

Ultimaker 2 Go Manuale utente

Ultimaker

Ultimaker Ultimaker S5 Pro Bundle Manuale utente

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker 2+ Connect Manuale per l'uso e la cura

Manuali Stampante 3D popolari di altre marche

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente

LONGER

LONGER LK4 Pro Manuale utente