Uplus Lighting 750 BSWF Manuale utente

User manual

750 BSWF

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

2.Technical Specifications………………………………………………………………………4-5

3.Description…………………………………………………………………………………………5

4.LED Light Source…………………………………………………………………………………6

5.Control Menu ……………………………………………………………………………………6-8

6.Universal DMX controller control……………………………………………………………8-9

7.DMX Channels …………………………………………………………………………………10-14

8.Dimension…………………………………………………………………………………………15

9.Trouble Shooting…………………………………………………………………………………16

10.Fixture Cleaning………………………………………………………… ………………………16

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

Power Supply：100~240V，50/60Hz

Power：The whole lamp power is 950W (90V), power factor: PF ≥ 0.98

Lamp：750W LED module (rated life of bulb: 20000h)

Color temperature：7500K

Electronic control technology：

Display with battery, able to Edit menu without power

Fan intelligent control, temperature electronic sensor detection.

DMX channel level monitoring, LCD screen lamp information query, RDM data two-way transmission.

Non contact magnetic rotary encoder positioning, signal feedback, absolute position memory, offline

power off position recovery.

Optical system:

1.Efficient optical system

2.Strong light output

3.High quality optical lens

Moving：

1.Pan move angle 540°, Accuracy 2.11°/ Step, fine tuning accuracy 0.008 °

2.Tilt move angle 270°,The accuracy is 1.05°/ Step, fine tuning accuracy 0.004 °

3.pan and tilt magnetic rotary encoder positioning reset system.

4.with automatic error correction.

Dimming / stroboscopic:

Fast motorized iris 5-100% linear adjustment, with macro function and multi-effect change Electronic

dimming, 0-100% linear dimming, uniform light spot

The electronic stroboscopic speed is 1-25 times/sec. You can choose pulsation, asynchronous,

synchronous, random slow, medium, fast, etc

Significant: Equipped with a high CRI chip to switch the high CRI mode.

Optics: Spot uniformity 90%, color rendering index:800≥70/800H≥90

Color system: CMY+CTO Color mixing system

Color Wheel：1 color wheel, 6 colors plus white, half-color effect, color film can be positioned

arbitrarily, with rainbow effect of bidirectional rotation.

Gobo Wheel:

1.Gobo wheel：1 fixed gobo wheel, 8 gobo plus white circles; 1 rotating gobo wheel, 6 patterns plus

white circles;

2.With pattern jitter and pattern arbitrary positioning function. Magnetic positioning function,

convenient for initial position correction and maintenance

Prism:

Prism 1: 4Prisms, Prism 2: Six-sided gradient mirror；

It can be rotated and superimposed in both directions, and has a prism positioning function.

Atomization: 2 atomizing films, which can be switched independently or superimposed to use light、

Moderate fogging.

Cutting:

Mechanical linear iris, 5%-100% linear adjustment;

4 gratings realize fast and smooth cutting, each grating can be individually controlled in cutting and

degree;

Single light can be turned off completely, and the whole module can be rotated ±45°.

Zoom: 4.5°-50°，With automatic adjustment function.

Heat dissipation:

It adopts one-in-one-out design, cooling fan, and dust-proof window for heat dissipation.

Control:

Standard DMX512 protocol,

Art-net Ethernet control protocol,

SACN protocol and wireless

DMX512 control (optional)

Net weight:29.8Kg Gross weight (carton):34Kg

Product Size:690×400×500mm Packing size (carton):520×420×420mm

3. Description

Rear side of base

1.Fuse：20A Over current protection；

2.Power cable：Connect the power supply.

3.Ethernet interface:Used for network protocol

transfer;

4.DMX interface：For DMX 512 connection, use 3-

pin or 5-pin XLR signal cable to connect to the lamp

and DMX console, and input DMX signal;

4.LED Light Source

The ultraviolet light emitted by the LED light source is harmful to the eyes and skin. Please do not

look directly at the lamp when it is running.

1. In order to protect the lamp, when turning off the lamp, please turn off the LED light source first,

and then disconnect the power supply after running for at least 5 minutes.

2.Do not touch the LED light source with bare hands. Once touched by hand, scrub with alcohol

and then dry with a soft linen cloth.

3.Ensure that the LED light source is installed in the central position to ensure the best results.

5.Control Menu

5.1 The main function

Turn on the machine, press the ENTER button to enter the menu mode, use the UP and DOWN

buttons to find the menu. When the preset menu is displayed on the display, press the ENTER

button to confirm. Use the UP and DOWN buttons to select the submenu, press the ENTER button

to save the setting or automatically return to the previous menu.Press the MENU button to return,

or wait for 30 seconds to exit the menu mode automatically.

When there is no power connection, press the MENU button for 3 seconds to enter the menu

mode.After setting, press the ENTER button for 1 second or wait for 40 seconds before powering

off and automatically exit the setting function.

The main functions are shown in the table below.

Menu function

A degree

B degree menu

C degree menu

D degree menu

E degree menu

Set address

0-512

Advanced

settings

Horizontal reverse

Yes/No

Vertical reverse

Yes/No

Display rotation

Reverse/forward

(Default forward)

The screen is

automatically reversed

Yes/No

(Default yes)

The display is always on

Open/close

(Default close)

Optocoupler correction

Open/close

(Default close)

Data retention

Voice

Chinese/English

(Factory default

Chinese)

Error message

Yes/No

Factory settings

Select channel mode

Standard mode

(Factory default)

Operating

mode

53（CH）

Reduced mode

37（CH）

View current channel

Level

0-255

.......

Function/Reset

Manual control of lamps

Mode selection

DMX/Self-propelled/Voice

control/Scenes

Scene selection

Self-propelled

....

Scene selection

01-10

Scene time

01.X axis

0-255

...

0-255

53.Reset/

Function

0-255

Master-slave selection

automatic/

Slave/

Host

Fixture reset

Horizontal and vertical

Yes/No

Color

Yes/No

Pattern

Yes/No

Cutting group

Yes/No

Prism/focusing

Yes/No

All

Yes/No

Communication options

DMX/Art+DMX/

ArtNet/Wireless

(Default DMX)

Network Configuration

DHCP

IP Address

Subnet mask

Port settings

System

message

Device version number

Motor information

Device status

Broken record

Light source time

Equipment running time

Light source

Light source information

Dimming mode

smooth/fast

Fan mode

automatic/theater/Silent

Service Contact

Application

service

Equipment maintenance

times

Equipment fine-tuning

and calibration

Device data clear

Equipment usage record

5.2.Error message

Temperature error

The temperature detection board may be damaged.

Fan error

The fan and its control part may be broken

Magnetic error

For the magnetic sensitive function part may be broken.

Optocoupler error

The optocoupler and its control part may be broken.

The above situation may occur when opening or resetting the machine, and some parts

may be damaged. Please contact an authorized repair center.

6.Universal DMX controller control

6.1 Connection

1. In order to reduce signal errors and avoid signal weakening and interference during transmission,

a 90-120Ω (0.25W) resistance can be added between the 2 cores and the 3 cores of the DMX

output terminal of the last machine

2. Use the XLR signal cable to connect the lamp, one end to the output port of the lamp, and the

other end to the input port of the next lamp. The XLR signal line can only be used in series, not

in parallel. DMX512 signal transmission speed is very fast. Damage to the signal line, weak

soldering, poor contact, etc., will affect the signal transmission and cause the system to shut

down

3. When the machine power supply of a certain unit is disconnected, the connection of DMX output

and input is bypassed in order to maintain the connection of the DMX line.

4. Each lamp must have an address code, which can receive the information sent by the console,

the range is between 0-512（Usually 0&1 is the same as 1）.

5. The terminal of the DMX512 system needs to be equipped with a terminator to reduce signal

transmission errors.

6. 3-pin XLR connector:

3 core XLR ：PIN 1：GND，PIN 2：Negative signal，PIN 3：Positive signal

6.2 Channel settings

Press the ENTER button to enter the menu mode, select the operating mode → select the channel

mode,

Press the ENTER button to confirm.The current channel mode will flash on the display. Use the UP

and DOWN buttons to select standard mode 53 (CH), and press the ENTER button to save.Press

the MENU button to return to the previous menu or wait for 30 seconds to automatically exit the

menu mode.

6.3 Address code setting

When a general DMX controller is used to control the lamp, you need to set the starting address (1-

512) for the lamp so that the machine can receive the DMX signal.

Press the ENTER button to enter themenu mode, select the DMX function, press the ENTER button

to confirm. The current address will flash on the display, then use the UP/DOWN button to select

the address code (1-512), and press the ENTER button to save.

Please refer to the chart below to set the address codes of the first 4 fixtures:

Channel mode

Lamp 1 address code

Lamp 2 address code

Lamp 3 address code

Lamp 4 address code

53Channel

107

160

37Channel

114

6.4 DMX 512 channel

Please refer to the following channel diagram to control the lamps.

Note:

1. If the DMX signal is cut off, the lamp will keep the state before the signal is cut off, unless it is

reset.

7.DMX Channels

Standard

mode

53（CH）

Reduced

mode

37（CH）

Channel name

Channel value

Function

Level

000-255

0-540°

Level

fine-tuning

000-255

16bit adjustable

vertical

000-255

0-270°

Vertical fine-tuning

000-255

16bit adjustable

XY Speed

000-255

From fast to slow

Dimming

000-255

Light spot from dark to bright

Dimming fine-

tuning

000-255

16bit adjustable

Strobe

0-3

Turn off the light

4-127

Pulse stroboscopic, from slow to fast

128-191

Gradual stroboscopic, from slow to fast

192-251

Random strobe, from slow to fast

252-255

Turn on the light

CMY blue

000-255

Blue CMY，From shallow to deep

CMY rose Red

000-255

Rose red CMY，From shallow to deep

CMY yellow

000-255

Yellow CMY，From shallow to deep

CMY CTO

0-255

CTO，From shallow to deep

CMY HONG

0-9

No function

10-255

CMY HONG function

CMY HONG speed

0-255

CMY Color chip conversion function，

from slow to fast

Color wheel

0-8

white

9-17

red

18-26

green

27-35

blue

36-44

yellow

45-53

rose red

54-62

fluorescence

63-70

white+red

71-78

red+green

79-86

green+blue

Indice

Altri manuali Uplus Lighting Attrezzatura di illuminazione

Uplus Lighting

Uplus Lighting 360 BEAM Manuale utente

Uplus Lighting

Uplus Lighting BR360 Manuale utente

Uplus Lighting

Uplus Lighting 4020 IP Manuale utente

Uplus Lighting

Uplus Lighting IP 300Z SPOT-WW Manuale utente

Uplus Lighting

Uplus Lighting 280 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 400 IP BLINDER Manuale utente

Uplus Lighting

Uplus Lighting 300 MZ-SPOT PR Manuale utente

Uplus Lighting

Uplus Lighting 37X15ZWASH Manuale utente

Uplus Lighting

Uplus Lighting 460LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 3010 IP PAR Manuale utente

Uplus Lighting

Uplus Lighting PIXEL IP20X15 BAR Manuale utente

Uplus Lighting

Uplus Lighting 250 LED BEAM Manuale utente

Uplus Lighting

Uplus Lighting MH12X40 PIXEL BAR Manuale utente

Uplus Lighting

Uplus Lighting 10X30 COB BAR Manuale utente

Uplus Lighting

Uplus Lighting IP MATRIX 5 Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 250 BEAM Manuale utente

Uplus Lighting

Uplus Lighting BAR 6 LASER Manuale utente

Uplus Lighting

Uplus Lighting 20 MINI SPOT Manuale utente

Uplus Lighting

Uplus Lighting IP1000 Strobe Manuale utente

Uplus Lighting

Uplus Lighting LED PROFILE MZ Manuale utente

Uplus Lighting

Uplus Lighting IP-L360 Manuale utente

Uplus Lighting

Uplus Lighting 200 BLINDER Manuale utente

Uplus Lighting

Uplus Lighting 6 EYE RETRO BAR Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente