Uplus Lighting BAR 6 LASER Manuale utente

User manual

BAR 6 LASER

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

Technical Specifications…………………………………………………………………………4

Control Menu ………………………………………………………………………………………5-6

DMX Channels ………………………………………………………………………………………7

Trouble Shooting……………………………………………………………………………………8

Fixture Cleaning………………………………………………………… …………………………8

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

Input Voltage: 100-240V,50/60Hz

Light Source: 6x2W RGB 3in1 Color (Red: 638 nm Green: 520 nm blue: 447 NM)

Laser Patterns: 128 Laser Animation Patterns (Built-in: Geometric Lines and Dotting Effect 2

Patterns)

Light source life: 50000 hours

Power:180W

Modulation signal:TTL modulation

Laser color:RGB full color Scanner:15KPPS*6pcs

Dimmer:0-100%(16bit)

Strobe:1-20Hz

DMX Channels: 12/62/60(10*6)CH

Control mode:DMX512, voice control, self-walking

Fixture Size:99*22*25; NW: 12 KG

3.Control Menu

Secondary menu

tertiary menu

1、DMX-512 Mode

DMX-512 Mode/

Address/

Channel/ Expert/

Address Setup/

Channel Setup/

Normal Mode/

Expert Mode/

2、Auto Mode

Auto Mode/

Effect/ Mix/

AutoSpeed/ 50%

Auto Effect/

Mix Show/

Lines Show/

Beams Show/

Auto Speed/self-propelled speed

50%

3、Music Mode

Music Mode/

Effect Mix/

MusicSpeed / 50%

Music Effect/

Mix Show/

Lines Show/

Beams Show/

Music Speed/

50%

4、Laser Light

Laser Light/

Scanner/20KPPS

Color/ RGB

Laser/ Analog

Invert/ Normal

Image Size X Y

Position/ X Y

Scan Rate/

15KPPS

Color Setup/

Single/

RGY

RBP

GBC

RGB

WYPC

Laser Type/

TTL /TTL

Analog/

Normal /

invert X /

invert Y /

invert XY/

Image Size/size setting

Size X /Size X

Size Y/SizeY

Position Setup/

position X/

position Y/

5、Settings

Settings/

Reset Default/

SafetyProtected/

Master Setup/

Back Light/

Language/

Display Setup/

About System/

Reset Default/

Yes/

No/

SafetyProtected/

Turn ON/

Turn OFF/

Master Setup/

Turn ON/

Turn OFF/

Back Light/

Normally ON/

Delay 15S OFF/

Language/

Chinese/

English/

Display Setup/

Rotate 180deg/

NormalDisplay/

LaserSystem2.9/

Software/

Version 1.0/Ver1.0

YM:20190301001

4.DMX Channels

12 CH Mode

Channel

value

Function

CH1

dimmer

0～255

dimmer 0~100%

CH2

red

0～255

Red 0~100%

CH3

green

0～255

Green 0~100%

CH4

blue

0～255

Blue 0~100%

CH5

Animation selection

0～255

One animation each 3 value

CH6

horizontal position

1～255

horizontal position selection

CH7

vertical position

1～255

vertical position selection

CH8

Pattern size

0～255

Pattern size selection

CH9

Line scan speed

0～127

Line scan speed

dot scan speed

128～255

dot scan speed

CH10

strobe

1～127

Strobe speed

Gradient

128～255

Gradient position

CH11

Pattern

0～127

Line effect

128～255

Dot effect

CH12

Mode select

0～26

Manual control mode

27～127

Built-in self-propelled mode speed selection

128～255

Built-in voice control mode speed selection

62 CH Mode

Channel

value

Function

CH61

Pattern

0～127

Line effect

128～255

Dot effect

CH62

Mode select

0～26

Manual control mode

27～127

Built-in self-propelled mode speed selection

128～255

Built-in voice control mode speed selection

60 CH Mode 10*6CH

Channel

value

Function

CH1

dimmer

0～255

dimmer 0~100%

CH2

red

0～255

Red 0~100%

CH3

green

0～255

Green 0~100%

CH4

blue

0～255

Blue 0~100%

CH5

Animation selection

0～255

One animation each 3 value

CH6

horizontal position

1～255

horizontal position selection

CH7

vertical position

1～255

vertical position selection

CH8

Pattern size

0～255

Pattern size selection

CH9

Line scan speed

0～127

Line scan speed

dot scan speed

128～255

dot scan speed

CH10

strobe

1～127

Strobe speed

Gradient

128～255

Gradient position

5.Trouble Shooting

ollo

ing

few

oble

y occu

uring

ope

tion

. He

tion

leshooting

The

does

work

, no

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

If th

nd no

espons

el,

che

ess

etti

s a

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

. One

the

cha

ing

tep

moto

dam

the

nect

to th

PCB

oken.

oto

’

ive

PCB

ndition

6.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,

smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Indice

Altri manuali Uplus Lighting Attrezzatura di illuminazione

Uplus Lighting

Uplus Lighting 750 BSWF Manuale utente

Uplus Lighting

Uplus Lighting MIX560 Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting IP-Z740 Manuale utente

Uplus Lighting

Uplus Lighting IP-L360 Manuale utente

Uplus Lighting

Uplus Lighting 360 BEAM Manuale utente

Uplus Lighting

Uplus Lighting 460LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 20 MINI SPOT Manuale utente

Uplus Lighting

Uplus Lighting DUAD540 STROBE Manuale utente

Uplus Lighting

Uplus Lighting 250 LED BEAM Manuale utente

Uplus Lighting

Uplus Lighting 250 BEAM Manuale utente

Uplus Lighting

Uplus Lighting MINI740 Manuale utente

Uplus Lighting

Uplus Lighting BSW 350 Manuale utente

Uplus Lighting

Uplus Lighting RETRO 360 Manuale utente

Uplus Lighting

Uplus Lighting 200 MZ-SPOT PR Manuale utente

Uplus Lighting

Uplus Lighting 150COBPAR Manuale utente

Uplus Lighting

Uplus Lighting 19X15Z WASH Manuale utente

Uplus Lighting

Uplus Lighting W3725 Manuale utente

Uplus Lighting

Uplus Lighting 4020 IP Manuale utente

Uplus Lighting

Uplus Lighting BL6 Manuale utente

Uplus Lighting

Uplus Lighting PF350 Manuale utente

Uplus Lighting

Uplus Lighting PIXEL IP20X15 BAR Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 200 BLINDER Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente