YASKAWA VIPA System SLIO Manuale utente
PS-CM | | Manual
HB300 | PS-CM | | en | 17-16
VIPA System SLIO
PS 007-1ABxx, CM 001-1BAxx
www.vipa.com/en/service-support/manual
SLIO_PS-CM,3,GB - © 2017
VIPA GmbH
Ohmstr. 4
91074 Herzogenaurach
Telephone: 09132-744-0
Fax: 09132-744-1864
Email: [email protected]
Internet: www.vipa.com
Table of contents
1 General.................................................................................................................... 4
1.1 Copyright © VIPA GmbH ................................................................................. 4
1.2 About this manual............................................................................................. 5
1.2.1 Safety information.......................................................................................... 6
2 Basics and mounting............................................................................................. 7
2.1 Safety information for users.............................................................................. 7
2.2 System conception........................................................................................... 8
2.2.1 Overview........................................................................................................ 8
2.2.2 Components.................................................................................................. 9
2.2.3 Accessories................................................................................................. 11
2.3 Dimensions..................................................................................................... 12
2.4 Mounting......................................................................................................... 14
2.4.1 Mounting CPU 01x...................................................................................... 14
2.5 Wiring............................................................................................................. 17
2.5.1 Wiring CPU 01x........................................................................................... 17
2.5.2 Wiring periphery modules............................................................................ 20
2.5.3 Wiring power modules................................................................................. 22
2.6 Demounting.................................................................................................... 26
2.6.1 Demounting CPU 01x.................................................................................. 26
2.6.2 Demounting periphery modules................................................................... 28
2.7 Trouble shooting - LEDs................................................................................. 30
2.8 Installation guidelines..................................................................................... 32
2.9 General data................................................................................................... 34
3 Power modules..................................................................................................... 36
3.1 Safety precautions.......................................................................................... 36
3.2 007-1AB00 - DC 24V 10A.............................................................................. 37
3.2.1 Technical data.............................................................................................. 40
3.3 007-1AB10 - DC 24V 4A, DC 24V/5V 2A....................................................... 42
3.3.1 Technical data.............................................................................................. 46
4 Clamp modules..................................................................................................... 48
4.1 001-1BA00 - 8xDC 24V clamps...................................................................... 48
4.1.1 Technical data.............................................................................................. 50
4.2 001-1BA10 - 8xDC 0V clamps........................................................................ 51
4.2.1 Technical data.............................................................................................. 53
4.3 001-1BA20 - 4xDC 24V and 4xDC 0V clamps............................................... 54
4.3.1 Technical data.............................................................................................. 56
VIPA System SLIO Table of contents
HB300 | PS-CM | | en | 17-16 3
1 General
1.1 Copyright © VIPA GmbH
This document contains proprietary information of VIPA and is not to be disclosed or used
except in accordance with applicable agreements.
This material is protected by the copyright laws. It may not be reproduced, distributed, or
altered in any fashion by any entity (either internal or external to VIPA), except in accord-
ance with applicable agreements, contracts or licensing, without the express written con-
sent of VIPA and the business management owner of the material.
For permission to reproduce or distribute, please contact: VIPA, Gesellschaft für Visuali-
sierung und Prozessautomatisierung mbH Ohmstraße 4, D-91074 Herzogenaurach, Ger-
many
Tel.: +49 9132 744 -0
Fax.: +49 9132 744-1864
EMail: [email protected]
http://www.vipa.com
Every effort has been made to ensure that the information contained in
this document was complete and accurate at the time of publishing. Nev-
ertheless, the authors retain the right to modify the information.
This customer document describes all the hardware units and functions
known at the present time. Descriptions may be included for units which
are not present at the customer site. The exact scope of delivery is
described in the respective purchase contract.
Hereby, VIPA GmbH declares that the products and systems are in compliance with the
essential requirements and other relevant provisions. Conformity is indicated by the CE
marking affixed to the product.
For more information regarding CE marking and Declaration of Conformity (DoC), please
contact your local VIPA customer service organization.
VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V,
System 500S and Commander Compact are registered trademarks of VIPA Gesellschaft
für Visualisierung und Prozessautomatisierung mbH.
SPEED7 is a registered trademark of profichip GmbH.
SIMATIC, STEP, SINEC, TIA Portal, S7-300 and S7-400 are registered trademarks of
Siemens AG.
Microsoft and Windows are registered trademarks of Microsoft Inc., USA.
Portable Document Format (PDF) and Postscript are registered trademarks of Adobe
Systems, Inc.
All other trademarks, logos and service or product marks specified herein are owned by
their respective companies.
Contact your local VIPA Customer Service Organization representative if you wish to
report errors or questions regarding the contents of this document. If you are unable to
locate a customer service centre, contact VIPA as follows:
All Rights Reserved
CE Conformity Declaration
Conformity Information
Trademarks
Information product sup-
port
VIPA System SLIO
General
Copyright © VIPA GmbH
HB300 | PS-CM | | en | 17-16
4
VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Telefax: +49 9132 744-1204
EMail: [email protected]
Contact your local VIPA Customer Service Organization representative if you encounter
problems with the product or have questions regarding the product. If you are unable to
locate a customer service centre, contact VIPA as follows:
VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Tel.: +49 9132 744-1150 (Hotline)
EMail: [email protected]
1.2 About this manual
The manual is targeted at users who have a background in automation technology.
The manual consists of chapters. Every chapter provides a self-contained description of a
specific topic.
The following guides are available in the manual:
nAn overall table of contents at the beginning of the manual
nReferences with page numbers
The manual is available in:
nprinted form, on paper
nin electronic form as PDF-file (Adobe Acrobat Reader)
Important passages in the text are highlighted by following icons and headings:
DANGER!
Immediate or likely danger. Personal injury is possible.
CAUTION!
Damages to property is likely if these warnings are not heeded.
Supplementary information and useful tips.
Technical support
Target audience
Structure of the manual
Guide to the document
Availability
Icons Headings
VIPA System SLIO General
About this manual
HB300 | PS-CM | | en | 17-16 5
1.2.1 Safety information
The system is constructed and produced for:
ncommunication and process control
ngeneral control and automation tasks
nindustrial applications
noperation within the environmental conditions specified in the technical data
ninstallation into a cubicle
DANGER!
This device is not certified for applications in
–in explosive environments (EX-zone)
The manual must be available to all personnel in the
nproject design department
ninstallation department
ncommissioning
noperation
CAUTION!
The following conditions must be met before using or commis-
sioning the components described in this manual:
– Hardware modifications to the process control system should only be
carried out when the system has been disconnected from power!
– Installation and hardware modifications only by properly trained per-
sonnel.
– The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Applications conforming
with specifications
Documentation
Disposal
VIPA System SLIO
General
About this manual > Safety information
HB300 | PS-CM | | en | 17-16 6
2 Basics and mounting
2.1 Safety information for users
VIPA modules make use of highly integrated components in MOS-Technology. These
components are extremely sensitive to over-voltages that can occur during electrostatic
discharges. The following symbol is attached to modules that can be destroyed by elec-
trostatic discharges.
The Symbol is located on the module, the module rack or on packing material and it indi-
cates the presence of electrostatic sensitive equipment. It is possible that electrostatic
sensitive equipment is destroyed by energies and voltages that are far less than the
human threshold of perception. These voltages can occur where persons do not dis-
charge themselves before handling electrostatic sensitive modules and they can damage
components thereby, causing the module to become inoperable or unusable. Modules
that have been damaged by electrostatic discharges can fail after a temperature change,
mechanical shock or changes in the electrical load. Only the consequent implementation
of protection devices and meticulous attention to the applicable rules and regulations for
handling the respective equipment can prevent failures of electrostatic sensitive modules.
Modules must be shipped in the original packing material.
When you are conducting measurements on electrostatic sensitive modules you should
take the following precautions:
nFloating instruments must be discharged before use.
nInstruments must be grounded.
Modifying electrostatic sensitive modules you should only use soldering irons with
grounded tips.
CAUTION!
Personnel and instruments should be grounded when working on electro-
static sensitive modules.
Handling of electrostatic
sensitive modules
Shipping of modules
Measurements and altera-
tions on electrostatic sen-
sitive modules
VIPA System SLIO Basics and mounting
Safety information for users
HB300 | PS-CM | | en | 17-16 7
2.2 System conception
2.2.1 Overview
System SLIO is a modular automation system for assembly on a 35mm mounting rail. By
means of the peripheral modules with 2, 4 or 8 channels this system may properly be
adapted matching to your automation tasks. The wiring complexity is low, because the
supply of the DC 24V power section is integrated to the backplane bus and defective
modules may be replaced with standing wiring. By deployment of the power modules in
contrasting colors within the system, further isolated areas may be defined for the DC
24V power section supply, respectively the electronic power supply may be extended with
2A.
VIPA System SLIO
Basics and mounting
System conception > Overview
HB300 | PS-CM | | en | 17-16 8
2.2.2 Components
nCPU (head module)
nBus coupler (head module)
nLine extension
nPeriphery modules
nAccessories
CAUTION!
Only modules of VIPA may be combined. A mixed operation with third-
party modules is not allowed!
With this CPU 01xC, the CPU electronic, input/output components and power supply are
integrated to one casing. In addition, up to 64 periphery modules of the System SLIO can
be connected to the backplane bus. As head module via the integrated power supply
CPU electronic and the I/O components are power supplied as well as the electronic of
the connected periphery modules. To connect the power supply of the I/O components
and for DC 24V power supply of via backplane bus connected peripheral modules, the
CPU has removable connectors. By installing of up to 64 periphery modules at the back-
plane bus, these are electrically connected, this means these are assigned to the back-
plane bus, the electronic modules are power supplied and each periphery module is con-
nected to the DC 24V power section supply.
With this CPU 01x, the CPU electronic and power supply are integrated to one casing. As
head module, via the integrated power module for power supply, CPU electronic and the
electronic of the connected periphery modules are supplied. The DC 24 power section
supply for the linked periphery modules is established via a further connection of the
power module. By installing of up to 64 periphery modules at the backplane bus, these
are electrically connected, this means these are assigned to the backplane bus, the elec-
tronic modules are power supplied and each periphery module is connected to the DC
24V power section supply.
CAUTION!
CPU part and power module may not be separated!
Here you may only exchange the electronic module!
With a bus coupler bus interface and power module is integrated to one casing. With the
bus interface you get access to a subordinated bus system. As head module, via the inte-
grated power module for power supply, bus interface and the electronic of the connected
periphery modules are supplied. The DC 24 power section supply for the linked periphery
modules is established via a further connection of the power module. By installing of up to
64 periphery modules at the bus coupler, these are electrically connected, this means
these are assigned to the backplane bus, the electronic modules are power supplied and
each periphery module is connected to the DC 24V power section supply.
CPU 01xC
CPU 01x
Bus coupler
VIPA System SLIO Basics and mounting
System conception > Components
HB300 | PS-CM | | en | 17-16 9
CAUTION!
Bus interface and power module may not be separated!
Here you may only exchange the electronic module!
In the System SLIO there is the possibility to place up to 64 modules in on line. By means
of the line extension you can divide this line into several lines. Here you have to place a
line extension master at each end of a line and the subsequent line has to start with a line
extension slave. Master and slave are to be connected via a special connecting cable. In
this way, you can divide a line on up to 5 lines. For each line extension the maximum
number of pluggable modules at the System SLIO bus is decreased by 1. To use the line
extension no special configuration is required.
Each periphery module consists of a terminal and an electronic module.
1 Terminal module
2 Electronic module
The terminal module serves to carry the electronic module, contains the backplane bus
with power supply for the electronic, the DC 24V power section supply and the staircase-
shaped terminal for wiring. Additionally the terminal module has a locking system for
fixing at a mounting rail. By means of this locking system your SLIO system may be
assembled outside of your switchgear cabinet to be later mounted there as whole system.
Line extension
Periphery modules
Terminal module
VIPA System SLIO
Basics and mounting
System conception > Components
HB300 | PS-CM | | en | 17-16 10
Altri manuali per VIPA System SLIO
3
Indice
Altri manuali YASKAWA Unità di controllo
YASKAWA
YASKAWA S-II Series Manuale utente
YASKAWA
YASKAWA JEPMC-OP3C01-E Manuale utente
YASKAWA
YASKAWA 62K-JJK0 Manuale utente
YASKAWA
YASKAWA Profibus-DP SGDH Series Manuale utente
YASKAWA
YASKAWA FM 054 Manuale utente
YASKAWA
YASKAWA System 300S+ CPU 315-4PN43 Manuale utente
YASKAWA
YASKAWA Motoman MLX200 Manuale utente
YASKAWA
YASKAWA FM 054 Manuale utente
YASKAWA
YASKAWA System 300S CP 342-1DA70 Manuale utente
YASKAWA
YASKAWA motoman NX100 Manuale utente
YASKAWA
YASKAWA VIPA System SLIO Manuale utente
YASKAWA
YASKAWA VIPA SPEED7 Manuale utente
YASKAWA
YASKAWA VIPA System 200V Manuale utente
YASKAWA
YASKAWA V1000 SI-EM3D/V Manuale utente
YASKAWA
YASKAWA YASNAC 3000G Manuale utente
YASKAWA
YASKAWA VIPA IM 053IP Manuale utente
YASKAWA
YASKAWA SI-EP3/V Manuale utente
YASKAWA
YASKAWA IM 053MT Manuale utente
YASKAWA
YASKAWA SI-ES3 Manuale utente
YASKAWA
YASKAWA AC Drive V1000 Option SI-EM3/V Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
