Advantech B+B SmartWorx IE-iMcV-2xLIM Manuale utente

IE-iMcV-2xLIM

USER MANUAL

IE-iMcV-2xLIM

Advantech B+B SmartWorx - Americas

707 Dayton Road

Ottawa, IL 61350 USA

Phone 1 (815) 433-5100

Fax 1 (815) 433-5105

Advantech B+B SmartWorx - European Headquarters

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone +353 91-792444

Fax +353 91-792445

www.advantech-bb.com

B+B SMARTWORX TECHNICAL SUPPORT

USA/Canada: 1 (800) 346-3119 (Ottawa, IL USA)

Monday - Friday

Europe: +353 91 792444 (Oranmore, Co Galway, Ireland)

Monday - Friday

Email: support@advantech-bb.com

Web: www.advantech-bb.com

IE-iMcV-2xLIM

TABLE OF CONTENTS

FCC Radio Frequency Interference Statement .................................................... 3

About This Manual ............................................................................................... 3

About the IE-iMcV-2xLIM...................................................................................... 4

Configuration Instructions..................................................................................... 4

Installing the IE-iMcV-2xLIM................................................................................. 5

Managed Modules................................................................................................ 5

Configuration Control & SNMP Management....................................................... 5

Unmanaged Modules ........................................................................................... 6

LED Operation...................................................................................................... 6

FX LinkLoss, TX LinkLoss, Link Fault Pass Through, Far End Fault.................... 8

Link Integrity......................................................................................................... 8

FX LinkLoss (FXLL).............................................................................................. 8

TX LinkLoss (TXLL).............................................................................................. 8

Link Fault Pass Through (LFPT) .......................................................................... 9

Far End Fault (FEF) ............................................................................................. 9

Auto Negotiation .................................................................................................. 9

Auto Cross Feature for Twisted Pair Connection ............................................... 10

Disable TX Port (DIS-TX) ................................................................................... 10

LED Operation.................................................................................................... 11

Installation Troubleshooting................................................................................ 12

Specifications ..................................................................................................... 12

Fiber Optic Cleaning Guidelines......................................................................... 13

Electrostatic Discharge Precautions................................................................... 13

Certifications....................................................................................................... 14

IE-iMcV-2xLIM

FCC RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

computing device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which the user will be required to correct the

interference at his own expense. Any changes or modifications not expressly

approved by the manufacturer could void the user’s authority to operate the

equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI

limits. This digital apparatus does not exceed the Class B limits for radio noise

emission from digital apparatus set out in the Radio Interference Regulation of

the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant

les limites applicables aux appareils numériques de classe B prescrites dans le

Règlement sur le brouillage radioélectrique publié par le ministère des

Communications du Canada.

ABOUT THIS MANUAL

to change without notice and does not represent a commitment on the part of

B+B SmartWorx. B+B SmartWorx assumes no responsibility for errors that may

appear in this document. B+B SmartWorx shall not be liable for incidental or

consequential damages resulting from the furnishing, performance or use of this

manual.

No part of this publication may be reproduced or transmitted in any form or by

any means, electronic or mechanical, including photography, recording or any

information storage and retrieval system without written consent.

Other brands or product names used in this manual may be registered

trademarks and the property of their respective owners. The use of trademarks or

other designations in this publication is for reference purposes only and does not

constitute an endorsement by the trademark holder.

IE-iMcV-2xLIM

ABOUT THE IE-IMCV-2XLIM

The IE-iMcV-2xLIM, TX/SFP is a Fast Ethernet module that provides two

conversions of 100Base-TX twisted pair to 100Base-FX/SX single-mode or multi-

mode fiber. There are two sets of ports, each providing an RJ-45 (copper) to SFP

(fiber) an SFP,155 Mbps, can be installed in the SFP port.

IE-iMcV-2xLIM, TX/SFP with Configuration Control support allows two

wavelengths to share one fiber strand - full-duplex data travels on different

wavelengths (for example,1310 nm and 1550 nm) - doubling the capacity of fiber.

The IE-iMcV-2xLIM, TX/SFP is SNMP-manageable and can be installed into the

modular, SNMP-manageable iMediaChassis, the MediaChassis series, or the

MediaChassis series which are unmanaged.

A single DIP Switch bay offers configuration for each RJ-45 to fiber interface set:

DSW 1-5 for Port 1 and DSW 6-10 for Port 2.

NOTE: Some options require items that are sold separately, available from B+B SmartWorx.

CONFIGURATION INSTRUCTIONS

The IE-iMcV-2xLIM, TX/SFP has user-configurable maintenance features (e.g.,

TX LinkLoss (TXLL), FX LinkLoss (FXLL), Link Fault Pass-Through (LFPT) and

Far End Fault (FEF)). Refer to the iMcV-Module DIP Switch configuration table

for information on available features. Instructions for configuring both managed

(via an SNMP-compatible management application like iView²) and unmanaged

modules follow.

IE-iMcV-2xLIM

INSTALLING THE IE-IMCV-2XLIM

The iMcV-2xLIM module installs in B+B SmartWorx’ SNMP manageable

iMediaChassis series or in any MediaChassis.

To install iMcV-2xLIM modules:

1. Remove the blank bracket covering the slot where the module is to be

installed by removing the screws on the outside edges of the bracket.

2. Slide the modules into the chassis, via the card guides, until the module is

seated securely in the connector.

3. Secure the module to the chassis by tightening the captive screw.

4. Save any “blanks” removed during installation for future use if configuration

requirements change.

NOTE:All modules are hot swappable.

NOTE: Some options require items that are sold separately, available from B+B SmartWorx.

MANAGED MODULES

To manage one or more iMcV-2xLIM modules, an SNMP agent must be present

in the chassis. To configure managed modules, install the module first, and then

configure using the management software.

CONFIGURATION CONTROL & SNMP MANAGEMENT

The iMcV-2xLIM module offers Configuration Control that has been implemented

to assist the end user for the following:

•Any module, iMcV-2xLIM or SNMP management sodule, can be

changed under power without losing any configuration.

•The management module can be added to a chassis without losing any

configuration that the modules have been set to.

•The management module will not be subjected to a “Mission Critical”

condition. If the management module is removed or fails, the iMcV-

2xLIM modules will not experience an interruption in service.

Configuration Control was created to solve the following issues:

•When non-Configuration Control iMcV-modules are placed in a

managed chassis, the iMcV-module’s DIP Switches are ignored

IE-iMcV-2xLIM

and the iMcV-module is configured by the chassis’ management

module. If the SNMP management module is removed or fails, the

iMcV-modules will revert back to the DIP Switch settings. When an

iMcV-module configuration changes from the management

module’s settings to DIP Switch settings, the traffic across the

iMcV-module will be interrupted for a very short period of time.

•When introducing a Management Module to a chassis full of

working non-Configuration Control iMcV-modules, the iMcV-

modules will stop using the DIP Switch settings and start using the

Management module’s settings. When an iMcV-module changes

from DIP Switch settings to the Management module’s settings, the

traffic across the iMcV-modules will be interrupted for a very short

period of time

•When removing an existing iMcV-module and replacing it with a

different iMcV-module, the configuration of the former iMcV-module

remains.

UNMANAGED MODULES

Before installing, configure the IE-iMcV-2xLIM, TX/SFP modules for the desired

features. The table below indicates the available features and settings for the IE-

iMcV-2xLIM, TX/SFP modules.

After configuring the DIP Switches for the desired settings, install the module and

connect the appropriate cables (refer to Installing an IE-iMcV-2xLIM, TX/SFP

section for more information).

IE-iMcV-2xLIM

IE-iMcV-2xLIM, TX/SFP and Configuration Control

DIP Switch

on S1

Feature

Default

Setting

Auto Negotiation (AN) (Port A) ON

FX LinkLoss (FXLL) (Port A) Off

TX LinkLoss (TXLL) (Port A) Off

Far End Fault (FEF) (Port A)

Off

Enable TX Port (Port A)

Auto Negotiation (AN) (Port B)

FX LinkLoss (FXLL) (Port B)

Off

TX LinkLoss (TXLL) (Port B)

Off

Far End Fault (FEF) (Port B)

Off

Enable TX Port (Port B) ON

NOTE: When possible, it is always advised to configure DIP Switches to match software settings.

IE-iMcV-2xLIM

FX LINKLOSS, TX LINKLOSS, LINK FAULT PASS-

THROUGH, FAR END FAULT

IE-iMcV-2xLIM, TX/SFP modules include the troubleshooting features: TXLL,

FXLL, FEF and LFPT that help locate silent failures on a network. Before

attempting to install the module(s), it is advised to understand how these features

work and react to a specific network configuration.

LINK INTEGRITY

During normal operation, link integrity pulses are transmitted by all point-to-point

Ethernet devices. When a B+B SmartWorx media converter receives valid link

pulses, it knows that the device to which it is connected is active and sending

pulses, and that the copper or fiber cable coming from that device is intact. The

appropriate “LNK” (link) LED is lit to indicate this.

The media converter also sends out link pulses from its copper and fiber

transmitters, but normally has no way of knowing whether the cable to the other

device is intact and the link pulses are reaching the other end. The combination

of FEF and LinkLoss allows this information to be obtained, even when physical

access to a remote device (and its link integrity LED) is not available.

FX LINKLOSS (FXLL)

FX LinkLoss is a troubleshooting feature. When enabled, if a fault occurs on the

fiber segment of a conversation, FX LinkLoss detects the fault and passes this

information to the twisted pair segment. If a media converter is not receiving a

fiber link, FX LinkLoss disables the transmitter on the media converter’s twisted

pair port. This results in a loss of link on the device connected to the twisted pair

port, and the TXLL LED will blink.

TX LINKLOSS (TXLL)

TX LinkLoss is a troubleshooting feature. When enabled, if a fault occurs on the

twisted pair segment of a conversion, TX LinkLoss detects the fault and passes

this information to the fiber segment. If a media converter is not receiving a

twisted pair link, TX LinkLoss disables the transmitter on the media converter's

fiber port. This results in a loss of the link on the device connected to the fiber

port, and the FXLL LED will blink.

IE-iMcV-2xLIM

LINK FAULT PASS-THROUGH (LFPT)

Link Fault Pass-Through (LFPT) is a troubleshooting feature that combines TX

and FX LinkLoss from both the local and remote IE-iMcV-2xLIM, TX/SFP

modules. LFPT is enabled by turning on both FX and TX LinkLoss on both

modules. This feature allows either end of the conversion to detect a link fault

occurring at the other end of the media conversion chain.

Regardless if there is a break in segment 1, 2 or 3, the link will drop on the

switches at both ends. The link fault is passed through the media conversion and

is observed at each end. It acts just like it would if the devices were directly

connected.

FAR END FAULT (FEF)

By default, FEF is disabled. When enabled, and a fault occurs on the fiber line,

affecting data in one direction, an FEF signal will be sent in the opposite

direction, indicating the fault. When enabling LFPT, FXLL will act on this signal

propagating the loss of link to the

cop

per port when FXLL is enabled.

For more information on LinkLoss, visit the B+B SmartWorx. If unsure of how to

use these features in a specific configuration, contact B+B SmartWorx.

AUTO NEGOTIATION

The IE-iMcV-2xLIM, TX/SFP module includes Auto Negotiation. When Auto

Negotiation is enabled, the module negotiates as a 100 Mbps full-duplex device.

If the connected device can operate at 100 Mbps full-duplex and support Auto

Negotiation, a link is established. Auto Negotiation (DIP Switch #1) is enabled by

default.

If the twisted pair port on the other device does not have the ability to Auto

Negotiate or if the 100 Mbps half-duplex connection is desired, then Auto

Negotiation must be disabled. Half-duplex and full-duplex settings must be set

manually to match the connected devices.

The following diagram shows a typical application with three possible

configurations.

Indice

Altri manuali Advantech Unità di controllo

Advantech

Advantech PCM-3614I Manuale di installazione e funzionamento

Advantech

Advantech USB-4716 Manuale di installazione e funzionamento

Advantech

Advantech ADAM-3750 3-Wire Series Manuale di installazione e funzionamento

Advantech

Advantech PCM-24BXWF Manuale di installazione e funzionamento

Advantech

Advantech PCA-TPMSPI Manuale di installazione e funzionamento

Advantech

Advantech PCM-3718 Series Manuale utente

Advantech

Advantech EDG-4100 Series Guida rapida

Advantech

Advantech PCM-3531 Manuale di installazione e funzionamento

Advantech

Advantech iDAQ-817 Manuale utente

Advantech

Advantech Network Device USB-4761 Manuale di installazione e funzionamento

Advantech

Advantech PCM-261 Manuale di installazione e funzionamento

Advantech

Advantech Adam 4000 Series Manuale utente

Advantech

Advantech MIC-75G20-10B1 Manuale di installazione e funzionamento

Advantech

Advantech PCM-3347 Series Manuale utente

Advantech

Advantech SOM-6898 Manuale utente

Advantech

Advantech PCM-3612I Manuale di installazione e funzionamento

Advantech

Advantech SOM-5893 Manuale utente

Advantech

Advantech Network Device USB-4761 Manuale di installazione e funzionamento

Advantech

Advantech ADAM-3656 Manuale di installazione e funzionamento

Advantech

Advantech ADAM-5240 Manuale utente

Advantech

Advantech ADAM-3016 Manuale utente

Advantech

Advantech ADAM-5000 Series Manuale utente

Advantech

Advantech EH-8100 Manuale utente

Advantech

Advantech RISC Module SOM-A2552 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente