Agilent Technologies 100 Manuale utente
100 Automated Disintegration Apparatus
Operator’s Manual
Notices
Manual Part Number
SD-29001863 Rev. E
Edition: 03/2022
Copyright
© Agilent Technologies, Inc. 2020, 2022
No partof this manual may be
reproduced in any form or by any means
(including electronic storage and retrieval
or translation into a foreign language)
without prior agreement and written
consent from Agilent Technologies, Inc.
as governed by United States and
international copyright laws.
Agilent Technologies, Inc.
3501 Stevens Creek Blvd.
Santa Clara, CA 95052 USA
Warranty
The material contained in this document
is provided “as is,” and is subject to being
changed, without notice, in future
editions. Further, to the maximum extent
permitted by applicable law, Agilent
disclaims all warranties, either express or
implied, with regard to this manual and
any information contained herein,
including but not limited to the implied
warranties of merchantability and fitness
for a particular purpose. Agilent shall not
be liable for errors or for incidental or
consequential damages in connection
with the furnishing, use, or performance
of this document or of any information
contained herein. Should Agilent and the
user have a separate written agreement
with warranty terms covering the
material in this document that conflict
with these terms, the warranty terms in
the separate agreement shall control.
Technology Licenses
The hardware and/or software described
in this document are furnished under a
license and may be used or copied only in
accordance with the terms of such
license.
Restricted Rights Legend
U.S. Government Restricted Rights.
Software and technical data rights
granted to the federal government
include only those rights customarily
provided to end user customers. Agilent
provides this customary commercial
license in Software and technical data
pursuant to FAR 12.211 (Technical Data)
and 12.212 (Computer Software) and, for
the Department of Defense, DFARS
252.227-7015 (Technical Data -
Commercial Items) and DFARS
227.7202-3 (Rights in Commercial
Computer Software or Computer
Software Documentation).
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in damage to the product or
loss of important data. Do not
proceed beyond a CAUTION
notice until the indicated
conditions are fully understood
and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in personal injury or death.
Do not proceed beyond a
WARNING notice until the
indicated conditions are fully
understood and met.
100 Operator’s Manual 3
Content
This manual covers the following modules:
•Agilent 100 Automated Disintegration Apparatus (G7962A)
1Safety 6
Electrical Hazards 7
Warning 8
Caution 8
Note 8
Information Symbols 9
2Introduction 10
Introduction 11
Conventions Used in this Manual 12
Serial Number Format 12
3 Setting Up the 100 13
Unpacking Your 100 14
Environmental Requirements for Installation 15
Setting up the Water Bath 16
Initial Power Up 17
Electrical Connections 17
Content
4100 Operator’s Manual
Installing the Temperature Probe 19
Water Bath Status LEDs 20
Setting the Date / Time Clock 21
Mounting Baskets and Filling Beakers 22
Draining the Water Bath 22
Hidden Key Functions 23
4 Operating the 100 24
Setting Water Bath Temperature 25
Setting Print Frequency for the Report Center Printer 25
Adjusting Basket Height 26
Placing Dosage Units in the Baskets 27
Selecting Operating Mode 27
Single-basket Operation 27
Multi-basket Operation 28
Three-Basket Operation 31
Printer Operation During Manual or Program Operation (Optional) 31
5 Troubleshooting and Maintenance 32
Preventive Maintenance 33
Weekly Maintenance 33
Monthly Maintenance 33
Every Six Months Maintenance 34
Yearly Maintenance 34
Disintegration Basket Care 35
Water Bath / Acrylic Care 36
Visual Checks 37
Water Bath Temperature Probe Accuracy Test 38
6100 Operator’s Manual
1Safety
Electrical Hazards 7
The Agilent 100 (G7962A) has been designed and tested so that when used
properly you have an accurate, fast, flexible, and safe instrument.
If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
The Agilent 100 (G7962A) is operated in conjunction with equipment that uses
aqueous liquids. Unskilled, improper, or careless use of this instrument can
create shock hazards, fire hazards, or other hazards which can cause death,
serious injury to personnel, or severe damage to equipment and property.
Information on safety practices is provided with your instrument and operation
manuals. Before using your instrument or accessories, you must thoroughly read
these safety practices.
Observe all relevant safety practices at all times.
1Safety
100 Operator’s Manual 7
Electrical Hazards
The Agilent 100 (G7962A) contains electrical circuits, devices, and components
operating at dangerous voltages. Contact with these circuits, devices, and
components can cause death, serious injury, or painful electric shock.
Panels or covers that are retained by fasteners which require the use of a tool for
removal may be opened only by Agilent-trained, Agilent-qualified, or
Agilent-authorized service engineers. Consult the manuals or product labels
supplied with the 100 to determine which parts are operator-accessible.
Application of the wrong supply voltage, connection of the instrument to an
incorrectly wired supply outlet, or lack of proper electrical grounding can create a
fire hazard or a potentially serious shock hazard and could seriously damage the
instrument and any attached ancillary equipment.
Always use a three-wire outlet with ground connection which is adequately rated
for the load. The installation must comply with local, state, and federal safety
regulations.
Do not connect the instrument to the main power supply until you have made
sure that the operating voltage is correctly set for the main power supply in the
specific outlet in your laboratory to which the equipment will be connected.
1Safety
8100 Operator’s Manual
Warning
WARNING
A ‘Warning’ message appears in the manual when failure to observe instructions
or precautions could result in death or injury.
Read all warnings and cautions carefully and observe them at all times.
Caution
CAUTION
A ‘Caution’ message appears in the manual when failure to observe instructions
could result in damage to equipment (Agilent supplied and / or other associated
equipment).
Note
NOTE
A ‘Note’ appears in the manual to give advice or information.
1Safety
100 Operator’s Manual 9
Information Symbols
I Switches main power on
0 Switches main power off
Indicates single-phase alternating current
The apparatus is marked with this symbol when the user shall
refer to the instruction manual in order to protect risk of harm to
the operator and to protect the apparatus against damage.
Confirms that a manufactured product complies with all
applicable European Community directives. The European
Declaration of Conformity is available at:
http://regulations.corporate.agilent.com/DoC/search.htm
Confirms that a manufactured product complies with all
applicable UK Regulation.
The UK Declaration of Conformity is available at:
http://regulations.corporate.agilent.com/DoC/search.htm
Indicates specific equipment meets standards of safety. These
products are safe for use in the workplace for North America.
This product complies with the European WEEE Directive
marking requirements. The affixed label indicates that you must
not discard this electrical/electronic product in domestic
household waste.
NOTE
Do not dispose of in domestic household waste!
To return unwanted products, contact your local Agilent office, or
see http://www.agilent.com for more information.
Indicates the product complies with regulatory compliance
requirements of New Zealand and Australia.
ISM1-A ISM classification according to CISPR11/EN55011: ISM Group 1
Class A
CAN ICES-001(A)
NMB-001(A)
This ISM device complies with Canadian ICES-001. Cet appareil
ISM est conforme à la norme NMB-001 du Canada
Altri manuali per 100
3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Agilent Technologies Attrezzature da laboratorio
Agilent Technologies
Agilent Technologies 5975 Series Manuale utente
Agilent Technologies
Agilent Technologies PlateLoc Manuale utente
Agilent Technologies
Agilent Technologies MX3000P Manuale utente
Agilent Technologies
Agilent Technologies 1100 Series Manuale utente
Agilent Technologies
Agilent Technologies 7010 Series Manuale utente
Agilent Technologies
Agilent Technologies 7250 Manuale utente
Agilent Technologies
Agilent Technologies Bravo Platform Manuale utente
Agilent Technologies
Agilent Technologies 1290 Infinity II Manuale utente
Agilent Technologies
Agilent Technologies Intuvo 9000 Foglio di istruzioni
Agilent Technologies
Agilent Technologies 1260 Infinity Manuale utente
Agilent Technologies
Agilent Technologies G3183B Istruzioni operative
Agilent Technologies
Agilent Technologies 1290 infinity Manuale utente
Agilent Technologies
Agilent Technologies 2200 TapeStation Manuale utente
Agilent Technologies
Agilent Technologies 1260 Infinity II Manuale utente
Agilent Technologies
Agilent Technologies Varian 3800 GC Manuale utente
Agilent Technologies
Agilent Technologies 1290 Infinity II 2D-LC Solution Manuale utente
Agilent Technologies
Agilent Technologies 700 Series Manuale utente
Agilent Technologies
Agilent Technologies Labware MiniHub G5584A Manuale utente
Agilent Technologies
Agilent Technologies N2792A Manuale utente
Agilent Technologies
Agilent Technologies 5100 ICP-OES Istruzioni operative
