Agilent Technologies 1156A Manuale utente
A
User’s Guide
Publication number 01156-97002
September 2005
For Safety and Regulatory information, see the pages at the back of this guide.
© Copyright Agilent Technologies 2001-2002, 2005
All Rights Reserved.
1156A 1.5 GHz Active Probe
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
Back to the Agilent 1156a Product Info Page
2
In This Book
This guide provides user and service information for the 1156A 1.5 GHz Active
Probe.
Chapter 1 gives you general information such as inspection, cleaning,
accessories supplied, and specifications and characteristics of the probe.
Chapter 2 shows you how to operate the probe and gives you information about
some important aspects of probing and how to get the best results with your
probe.
Chapter 3 provides service information.
Contents
3
1General Information
To inspect the probe 7
Accessories Supplied 8
Replaceable Parts and Additional Accessories 10
Characteristics and Specifications 11
General Characteristics 12
To use the probe 14
Probe handling considerations 14
Cleaning the probe 14
Using Probe Accessories 15
To connect the probe 16
2Operating the Probe
110 Ohm Resistive Signal Pin (Green) and Solderable Ground
Socket 21
130 Ohm Resistive Signal Pin (Orange) and Ground Blade
Assembly 25
5 cm Resistive Signal Leads and Solderable SMT or Solderable
Through-hole Ground Pin 29
Socket-end 10 cm Resistive Signal Lead and Solderable SMT or
Solderable Through-hole Ground Pin 33
Micro Clip 37
Undamped Accessories 37
3Service
Service Strategy 42
To return the probe to Agilent Technologies for service 43
Troubleshooting 44
Failure Symptoms 44
Probe Calibration Fails 44
Incorrect High Frequency Response 44
Incorrect Low Frequency Response (pulse flatness) 45
Incorrect Input Resistance 45
Incorrect Offset 45
Offset Will Not Zero 45
Verifying probe input resistance 46
!
6
1156A 1.5 GHz Active Probe
The 1156A 1.5 GHz Active Probe is a probe solution for high-frequency
applications. This probe is compatible with the AutoProbe Interface
which completely configures the Infiniium series of oscilloscopes for the
probe.
General Information
7
General Information
To inspect the probe
To inspect the probe
❏Inspect the shipping container for damage.
Keep a damaged shipping container or cushioning material until the contents of
the shipment have been checked for completeness and the instrument has been
checked mechanically and electrically.
❏Check the accessories.
Accessories supplied with the instrument are listed in "Accessories Supplied" in
table 1-1 later in this chapter.
• If the contents are incomplete or damaged notify your Agilent Technologies
Sales Office.
❏Inspect the probe.
• If there is mechanical damage or defect, or if the probe does not operate
properly or pass calibration tests, notify your Agilent Technologies Sales
Office.
• If the shipping container is damaged, or the cushioning materials show signs
of stress, notify the carrier as well as your Agilent Technologies Sales Office.
Keep the shipping materials for the carrier’s inspection. The Agilent
Technologies Office will arrange for repair or replacement at Agilent
Technologies’ option without waiting for claim settlement.
Figure 1-1
1156A Active Probe
01158e03.cdr
5 Accessory Vials
Accessories
Container
Included with
the probe is an
accessories
container and 5
accessory
vials. All the
included
accessories
are shown in
figure 1-2.
8
General Information
Accessories Supplied
Accessories Supplied
The following figure and table show the accessories supplied with the 1156A
Active Probe.
Figure 1-2
9
General Information
Accessories Supplied
Table 1-1
Accessories Supplied
Item Description Qty Agilent Part Number
1s 130 Ωresistive signal pin (orange) 12 01156-27616
2s Solderable-tip 5 cm resistive signal lead 2 01156-82106
3s Socket-end 5 cm resistive signal lead 2 01156-82105
4s Socket-end 10 cm resistive signal lead 2 01156-82108
5sg Micro clip 25063-2180
1g Ground blade assembly 12 01156-23701
2g Solderable SMT ground pin 12 1253-5054
3g Solderable through-hole ground pin 12 1252-7150
4g Offset ground pin 12 01156-27606
5g Solderable-tip 5 cm ground lead 2 01156-82107
6g Socket-end 5 cm ground lead 2 01156-82103
7g Socket-end 5 cm, 90° pin ground lead 2 01156-82104
10
General Information
Replaceable Parts and Additional Accessories
Replaceable Parts and Additional Accessories
Table 1-2
Replaceable Parts and Additional Accessories
Agilent Part Number Description Qty
E2638A Solderable-tip 5 cm resistive signal lead
Solderable-tip 5 cm ground lead
10
3
E2639A Micro clip 4
E2640A 130 Ωresistive signal pin (orange) 8
E2641A Ground blade assembly 8
E2637A Precision Measurement Kit
includes 2 solderable ground sockets and 2
110 Ωresistive signal pins (green)
1
E2654A EZ-Probe®positioner 1
11
General Information
Characteristics and Specifications
Characteristics and Specifications
The following characteristics are typical for the active probe.
Table 1-3
Characteristics
1 Denotes warranted specifications, all others are typical.
2 For waveforms with edges > 3 ns, the dynamic range is > 12.0 Vpeak-to-peak
3 Installation category (overvoltage category) I: Signal level, special equipment, or parts of
equipment, telecommunication, electronic, etc., with smaller transient overvoltages than
installation category (overvoltage category) II.
Bandwidth1(-3 dB) > 1.5 GHz
System bandwidth (-3 dB) 1156A with 54832B/D or 54835A scope: 1 GHz
Rise and Fall Time (10% to 90%) < 233 ps calculated from
Input Capacitance 0.8 pF
Input Resistance1100 kΩ \1%
Flatness, Swept Response 0.2 dB, 100 kHz to 100 MHz
0.4 dB, 100 MHz to 1.5 GHz
Flatness, Step Response 15% overshoot, 35 ps input edge
10% overshoot: 75 ps input edge; 2%: 1 ns after edge
Dynamic Range2> 5.0 V peak-to-peak
DC Attenuation 10:1
Offset error referred to input <\30 mV
Offset Range ±15.0 V
Offset Gain Accuracy <\3% of setting
Noise referred to input 3.0 mVrms
Propagation Delay 5.5 ns
Maximum Input Voltage340 V peak, CAT I
ESD Tolerance > 5 kV from 100 pF, 300 ΩHBM
Temperature Drift Offset: < 1.0 mV/°C
Attenuation: < 0.1 %/°C
tr
0.35
Bandwidth
-----------------------------=
!
12
General Information
General Characteristics
General Characteristics
The following general characteristics apply to the active probe.
Table 1-4
General Characteristics
Environmental Conditions
Operating Non-operating
Temperature 0 °C to +55 °C−40 °C to +70 °C
Altitude 4000 meter (13,000 ft)
Humidity up to 95% relative humidity
(non-condensing) at +40 °C
up to 90% relative humidity at +65 °C
Power Requirements +12 Vdc @ 3 mA typical
+5 Vdc @ 35 mA typical
-5 Vdc @ 37 mA typical
0.4 W
(voltages supplied by AutoProbe
Interface)
Weight approximately 0.69 kg
Dimensions Refer to the outline in figure 1-3.
Pollution degree 2 Normally only non-conductive pollution occurs. Occasionally, however, a
temporary conductivity caused by condensation must be expected.
Indoor use
Indice
Altri manuali Agilent Technologies Strumento di misura
Agilent Technologies
Agilent Technologies ESA-E E4407B Manuale di installazione e funzionamento
Agilent Technologies
Agilent Technologies FieldFox N9913A Manuale utente
Agilent Technologies
Agilent Technologies U1701A Manuale utente
Agilent Technologies
Agilent Technologies OmniBER 718 SDH Manuale utente
Agilent Technologies
Agilent Technologies HP E5574A Manuale utente
Agilent Technologies
Agilent Technologies 8712ET Manuale utente
Agilent Technologies
Agilent Technologies N5225-60114 Manuale di installazione e funzionamento
Agilent Technologies
Agilent Technologies N2771A Manuale utente
Agilent Technologies
Agilent Technologies 42841A Manuale utente
Agilent Technologies
Agilent Technologies LogicWave Manuale utente
Agilent Technologies
Agilent Technologies E5500A Manuale utente
Agilent Technologies
Agilent Technologies 86082A Manuale utente
Agilent Technologies
Agilent Technologies Agilent 8163A Manuale utente
Agilent Technologies
Agilent Technologies B1500A Guida all'installazione
Agilent Technologies
Agilent Technologies 100 Manuale utente
Agilent Technologies
Agilent Technologies E8356A Manuale di installazione e funzionamento
Agilent Technologies
Agilent Technologies 4352B Manuale utente
Agilent Technologies
Agilent Technologies N5242A Manuale utente
Agilent Technologies
Agilent Technologies 8753ES Manuale utente
Agilent Technologies
Agilent Technologies PSA Series Manuale di installazione e funzionamento
