Allen-Bradley 1794-OA8K Manuale utente

Installation Instructions

FLEX I/O AC Digital Output Modules

Catalog numbers

1794-OA8, 1794-OA8K, 1794-OA8I, 1794-OA16

Table of Contents

Topic Page

Important User Information 2

Environment and Enclosure 3

Preventing Electrostatic Discharge 3

European Hazardous Location Approval 5

North American Hazardous Location Approval 7

Install Your FLEX I/O AC Digital Output Module 8

Configure the FLEX I/O AC Output Module 15

Specifications 17

2FLEX I/O AC Digital Output Modules

Publication 1794-IN103D-EN-P - July 2018

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid

state equipment and hard-wired electromechanical devices. Because of this difference, and also because

of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you

identify a hazard, avoid a hazard, or recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

FLEX I/O AC Digital Output Modules 3

Publication 1794-IN103D-EN-P - July 2018

Environment and Enclosure

Preventing Electrostatic Discharge

ATTENTION: This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in

EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such

environments.

This equipment is supplied as open-type equipment for indoor use. It must be

mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread

of flame, complying with a flame spread rating of 5VA or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only

by the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to

comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of

the degrees of protection provided by enclosures.

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

4FLEX I/O AC Digital Output Modules

Publication 1794-IN103D-EN-P - July 2018

ATTENTION: This product is grounded through the DIN rail to chassis ground.

Use zinc plated chromate-passivated steel DIN rail to assure proper grounding.

The use of other DIN rail materials (for example, aluminum or plastic) that can

corrode, oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail

properly.

Refer to Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for more information

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be impaired.

ATTENTION: Read this document and the documents listed in the Additional

Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product.

Users are required to familiarize themselves with installation and wiring

instructions in addition to requirements of all applicable codes, laws, and

standards.

ATTENTION: Installation, adjustments, putting into service, use, assembly,

disassembly, and maintenance are required to be carried out by suitably

trained personnel in accordance with applicable code of practice.

In case of malfunction or damage, no attempts at repair should be made. The

module should be returned to the manufacturer for repair.

Do not dismantle the module.

ATTENTION: Use only a soft dry anti-static cloth to wipe down equipment. Do

not use any cleaning agents.

FLEX I/O AC Digital Output Modules 5

Publication 1794-IN103D-EN-P - July 2018

European Hazardous Location Approval

Approved for the 1794-OA8K module only.

WARNING: When you insert or remove the module while backplane power

is on, an electric arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electric arcing causes excessive wear to contacts on

both the module and its mating connector. Worn contacts may create

electrical resistance that can affect module operation.

WARNING: If you insert or remove the module while backplane power is on,

an electric arc can occur. This could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is nonhazardous before

proceeding.

The following applies to products marked II 3 G:

Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and

Safety Requirements relating to the design and construction of such equipment given in

Annex II to EU Directive 2014/34/EU. See the EU Declaration of Conformity at

http://www.rockwellautomation.com/global/certification/overview.page for details. The

type of protection is II 3G Ex nA IIC T3 Gc according to EN 60079-15.

Comply to Standards EN 60079-0:2012, EN 60079-15:2010, reference certificate number

LCIE 01 ATEX 6020 X.

Are intended for use in areas in which explosive atmospheres caused by gases, vapors,

mists, or air are unlikely to occur, or are likely to occur only infrequently and for short

periods. Such locations correspond to Zone 2 classification according to ATEX directive

2014/34/EU.

6FLEX I/O AC Digital Output Modules

Publication 1794-IN103D-EN-P - July 2018

WARNING: Observe the following additional certification

requirements:

• This equipment is not resistant to sunlight or other sources of UV

radiation.

• This equipment shall be mounted in an ATEX/IECEx Zone 2 certified

enclosure with a minimum ingress protection rating of at least IP54 (in

accordance with EN/IEC 60079-15) and used in an environment of not

more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when

applied in Zone 2 environments. The enclosure must be accessible only

by the use of a tool.

• This equipment shall be used within its specified ratings defined by

Rockwell Automation.

• The instructions in the user manual shall be observed.

• This equipment must be used only with ATEX certified Rockwell

Automation backplanes.

• Earthing is accomplished through mounting of modules on rail.

• Devices shall be used in an environment of not more than Pollution

Degree 2.

• Enclosure must be marked with the following: "Warning - Do not open

when energized." After installation of equipment into the enclosure,

access to termination compartments shall be dimensioned so that

conductors can be readily connected.

FLEX I/O AC Digital Output Modules 7

Publication 1794-IN103D-EN-P - July 2018

North American Hazardous Location Approval

The following modules are North American Hazardous Location approved: 1794-OA8,

1794-OA8K, 1794-OA8I, 1794-OA16.

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l’utilisation de cet

équipement en environnements dangereux:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for

use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When combining

products within a system, the most adverse temperature code

(lowest "T" number) may be used to help determine the

overall temperature code of the system. Combinations of

equipment in your system are subject to investigation by the

local Authority Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux. Chaque produit est livré avec des marquages

sur sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux. Lorsque

plusieurs produits sont combinés dans un système, le code

de température le plus défavorable (code de température le

plus faible) peut être utilisé pour déterminer le code de

température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection

par les autorités locales qualifiées au moment de

l'installation.

EXPLOSION HAZARD

• Do not disconnect equipment unless power

has been removed or the area is known to be

nonhazardous.

• Do not disconnect connections to this

equipment unless power has been removed

or the area is known to be nonhazardous.

Secure any external connections that mate

to this equipment by using screws, sliding

latches, threaded connectors, or other

means provided with this product.

• Substitution of components may impair

suitability for Class I, Division 2.

• If this product contains batteries, they must

only be changed in an area known to be

nonhazardous.

RISQUE D’EXPLOSION

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non dangereux

avant de débrancher les connecteurs.

Fixer tous les connecteurs externes reliés

à cet équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de Classe I,

Division 2.

• S'assurer que l'environnement est classé

non dangereux avant de changer les piles.

8FLEX I/O AC Digital Output Modules

Publication 1794-IN103D-EN-P - July 2018

Install Your FLEX I/O AC Digital Output Module

The module mounts on a 1794 terminal base.

1. Rotate the keyswitch (3) on the terminal base (4) clockwise to position 8as

required for this type of module.

2. Make sure the Flexbus connector (1) is pushed all the way to the left to connect

with the neighboring terminal base/adapter.

You cannot install the module unless the connector is fully extended.

3. Make sure the pins on the bottom of the module are straight so they will align

properly with the connector in the terminal base.

4. Position the module (7) with its alignment bar (6) aligned with the groove (5) on

the terminal base.

Description Description

1 Flexbus connector 5 Groove

2 Latching mechanism 6 Alignment bar

3 Keyswitch 7 Module

4 Terminal base

WARNING: 1794-TBNF and 1794-TBNFK are not approved for Class I

Division 2 Applications.

45284

FLEX I/O AC Digital Output Modules 9

Publication 1794-IN103D-EN-P - July 2018

5. Press firmly and evenly to seat the module in the terminal base unit. The module

is seated when the latching mechanism (2) is locked into the module.

Connecting Wiring for the 1794-OA8 or 1794-OA8K

1. For 1794-TB2, 1794-TB3, or 1794-TB3S – Connect individual output wiring

to even numbered terminals on the 0…15 row (A) as indicated in the Wiring

Connections for 1794-OA8 and 1794-OA8K table.

2. For 1794-TBN or 1794-TBNF – Connect individual output wiring to even

numbered terminals on the 16…33 row (B) as indicated in the Wiring

Connections for 1794-OA8 and 1794-OA8K table.

3. For 1794-TB2, 1794-TB3, or 1794-TB3S – Connect the associated V AC

common (L2) lead of the output device to the corresponding odd numbered

terminal on the 0…15 row (A) for each output as indicated in the Wiring

Connections for 1794-OA8 and 1794-OA8K table; or to the corresponding

terminal on the 16…33 row (B). The V AC common (L2) terminals of row (B)

and the odd numbered terminals of row (A) are internally connected together.

For 1794-TBN or 1794-TBNF – Connect the associated V AC common (L2)

lead of the output device to the corresponding odd numbered terminal on the

34…51 row (C) for each output as indicated in the Wiring Connections for

1794-OA8 and 1794-OA8K table. The odd numbered terminals of row (C) are

internally connected together to V AC L2 common.

4. Connect V AC power L1 to terminal 34 on the 34…51 row (C).

5. Connect V AC common L2 to terminal 16 on the 16…33 row (B).

6. If daisychaining V AC power (L1) to the next terminal base, connect a jumper

from terminal 51 (V AC L1) on this base unit to terminal 34 on the next base

unit.

7. If continuing V AC common (L2) to the next base unit, connect a jumper from

terminal 33 (V common L2) on this base unit to terminal 16 on the next base

unit.

IMPORTANT

Total current draw through terminal base connection is limited to 10 A.

Separate power connections to each terminal base may be necessary.

ATTENTION: If multiple power sources are used for 1794-OA8I, do not exceed

the specified isolation voltage.

10 FLEX I/O AC Digital Output Modules

Publication 1794-IN103D-EN-P - July 2018

1794-TB2, 1794-TB3, and 1794-TB3S Terminal Base Wiring for 1794-OA8

Wiring Connections for 1794-OA8 and 1794-OA8K

1794-TB2, 1794-TB3, 1794-TB3S 1794-TBN, 1794-TBNF

Output(1) Output Terminal Common

Terminal (L2)(1)

(1) A-1, 3, 5, 7, 9, 11, 13, and 15 on the 1794-TB2, 1794-TB3, and 1794-TB3S are internally connected in the module to 120V

AC common (L2).

Output Terminal Common

Terminal (L2)(2)

(2) C-1, 3, 5, 7, 9, 11, 13, and 15 on the 1794-TBN and 1794-TBNF are internally connected in the module to 120V AC

common (L2).

0 A-0 A-1/B-17 B-0 C-1

1 A-2 A-3/B-19 B-2 C-3

2 A-4 A-5/B-21 B-4 C-5

3 A-6 A-7/B-23 B-6 C-7

4 A-8 A-9/B-25 B-8 C-9

5 A-10 A-11/B-27 B-10 C-11

6 A-12 A-13/B-29 B-12 C-13

7 A-14 A-15/B-31 B-14 C-15

A = Output terminals (Even numbered terminals 0...14)

B = Common terminals

C = Power terminals (C-34 and C-51 on 1794-TB2;

C-34...C-51 on 1794-TB3 and 1794-TB3S)

B = Even numbered output terminals 0...14,

AC common terminals 16 and 33

C = Power terminals C-34 and C-51, and odd

numbered output terminals 1...15

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

Commons

(1794-TB3 shown)

Connect 120VAC common L2 to terminal B-16.

Connect 120VAC power L1 to terminal C-34.

L2 IN L2 OUT

Voltage

(Use B-33 and C-51 for daisy-chaining power to the next terminal base unit.)

L1 IN L1 OUT

(Terminals C-35…C-50 are not present on the 1794-TB2.)

45671

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Allen-Bradley Unità di controllo

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Manuale utente

Allen-Bradley

Allen-Bradley 1203-GD2 Manuale utente

Allen-Bradley

Allen-Bradley SLC 5/02 Manuale utente

Allen-Bradley

Allen-Bradley 1756-L7 Series Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Manuale

Allen-Bradley

Allen-Bradley CAB6-HA 2 Manuale utente

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Manuale utente

Allen-Bradley

Allen-Bradley DeviceNet 1771-SDN/C Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Manuale utente

Allen-Bradley

Allen-Bradley 193-DNENCAT Manuale utente

Allen-Bradley

Allen-Bradley ProcessLogix B Series Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1200 Manuale utente

Allen-Bradley

Allen-Bradley 160-DN2 Manuale utente

Allen-Bradley

Allen-Bradley 1770-KFDG Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1500 1764-MM1 Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-IT4IM12R Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet C Series Manuale utente

Allen-Bradley

Allen-Bradley A Series Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O PROFIBUS 1734-APB Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-HYD02 Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix ControlNet B Series Manuale utente

Allen-Bradley

Allen-Bradley D Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente