APS iBoard IB-R004 Manuale utente
Customer Support: info@iboardauto.com
Rev. 20211001
1
iBoard
®
iBoard® by APS PART#: IB-R004
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*DRILLING IS REQUIRED
Item QTY Description Item QTY Description
1# 8Mounting Brackets 5# 8M8 Nylon Lock Nuts
2# 8M8X1.25-20mm Hex Bolts 6# 16 M6X1-20mm Square Head Bolts
3# 24 ST6.3-25mm Hex Self Tapping Screws 7# 16 M6 Large Flat Washers
4# 16 M8 Flat Washers 8# 16 M6 Nylon Lock Nuts
2 # 6 # 7 # 8 #
5 #
4 #
3 #
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
Customer Support: info@iboardauto.com
Rev. 20211001
2
iBoard
®
PassengerDriver Front
1#
1#
1#
1#
1#
1#
1#
1#
Customer Support: info@iboardauto.com
Rev. 20211001
3
iBoard
®
STEP 1
Starting on the Driver side of the vehicle. Attach (1) Mounting
Bracket to the rocker panel with (3) ST6.3-25mm Hex Self Tapping
Screws per bracket (Fig 1). Don’t fully tighten at this time.
Note: (8) Mounting Brackets Are Universal.
STEP 2
Use the Mounting Bracket as template, mark and drill (4) 8mm
holes in pinch weld. If necessary, remove the brackets from the
rocker panel for drilling (Fig 2). Note: The dimensions on Fig
2 for reference only. It may be varied on some models.
(Fig 1) Driver Side Mounting Bracket Installation Exampled
STEP 3
Attach the Mounting Bracket onto the drilled holes on pinch
weld with (1) M8X1.25-20mm Hex Bolt, (2) M8 Flat Washers
and (1) M8 Nylon Lock Nut, (Fig 1). Don’t fully tighten at this
time.
(Fig 2) Driver Side Pinch Weld Mounting Holes
STEP 4
Select a Running Board. Slip (4) M6x1-20mm Square Head
Bolts into each bottom channel (Fig 3). Carefully position the
Running Board onto the (4) Mounting Brackets.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged. Attach the
Running Board to each Mounting Bracket with (2) M6x1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6
Nylon Lock Nuts (Fig 4). Do not fully tighten at this time.
(3) ST6.3-25mm Hex
Self Tapping Screws
(1) M8X1.25-20mm Hex Bolt
(2) M8 Flat Washers
(1) M8 Nylon Lock Nut
(Fig 3) Slip M6X1-20mm Square Head Bolts Into The
Bottom Channels
M6X1-20mm Square Head Bolts
Customer Support: info@iboardauto.com
Rev. 20211001
4
iBoard
®
(Fig 4) Running Board Installed Onto Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts
STEP 5
Level and adjust the Running Board and fully tighten all hard-
ware.
Important: Please follow the recommended Tightening Tor-
ques shown in the table on page 1. Don’t over tighten, or
the nuts/bolts will be damaged.
STEP 6
Repeat Steps 1-5 for the other side Running Board installation.
The installation is completed .
Attention
Do periodic inspections to the installation to make
sure that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.
Altri manuali APS Accessori per automobili
APS
APS iBoard IB-R046 Manuale utente
APS
APS iBoard IB-R094 Manuale utente
APS
APS IA06SAG5B Manuale utente
APS
APS iBoard IB-R054 Manuale utente
APS
APS iArmor IA-S926H Manuale utente
APS
APS GR18HEC11A Manuale utente
APS
APS GR18GEC00U Manuale utente
APS
APS IA06SJA1B Manuale utente
APS
APS iBoard IB-014A-B Manuale utente
APS
APS ELM205-V10 Manuale utente
APS
APS IB14DBB5B Manuale utente
APS
APS iArmor IA-S002H Manuale utente
APS
APS IA06SIB6B Manuale utente
APS
APS iBoard Manuale utente
APS
APS iBoard IB-019&020A-B Manuale utente
APS
APS iBoard IB-192A-B Manuale utente
APS
APS IB03DJJ7A Manuale utente
APS
APS IA20SJI8B Manuale utente
APS
APS IA10SAA1B Manuale utente
APS
APS iArmor IA-S926 Manuale utente
