Arrow Master 1350 Manuale utente

Publication No. 5000054

(Revised 09/12)

ARROW - MASTER

MOBILE HYDRAULIC HAMMER

MODEL 1350

Service Manual

SERIAL NUMBER:

SOLD AND

SERVICED BY:

ARROW-MASTER, INCORPORATED

1201 Seventh Street !East Moline, IL 61244

www.arrowmaster.com

5000054 09/12

Page i-1

Table Of Contents

Bolt and Cap Screw Torque Specification ...................................................i-3

Wheel Lug Nut Torque Specification .......................................................i-3

Adjustments

.....................................................7-1

CABLELENGTH ................................................................ 7-1

REPLACINGCABLE ............................................................. 7-1

CROSS-SLIDE BEARING ADJUSTMENT ............................................. 7-5

CARRIAGE BEARING END PLAY ................................................... 7-5

SIDESHIFTCHAIN............................................................... 7-6

PROXIMITYSENSOR ............................................................ 7-7

Hydraulic Pressure Adjustment

......................................8-1

REQUIREDEQUIPMENT ......................................................... 8-1

HAMMER LIFT CIRCUIT .......................................................... 8-1

CONTROL CIRCUIT MAIN RELIEF ...............................................8-2,8-8

SIDESHIFTCONTROL-VALVERELIEF ...........................................8-4,8-9

TILT AND LAYBACK CONTROL-VALVE RELIEF ....................................... 8-4

PILOT-CIRCUIT RELIEF (electronic stroke control) ..................................8-5,8-9

PILOT-CIRCUIT RELIEF (mechanical stroke control) .................................... 8-5

VALVESPOOLCENTERINGADJUSTMENT.......................................... 8-6

CREEPER VALVE RELIEF ....................................................... 8-10

Mechanical System

................................................9-1

ENGINE REPAIR ................................................................ 9-1

SERPENTINEBELTREPLACEMENT ............................................... 9-1

TRANSMISSION, CLUTCH, AXLES, BRAKES, AND STEERING VALVE .................... 9-2

CREEPER DRIVE ............................................................... 9-2

AdjustmentofGearBacklash .................................................... 9-2

Creeper-Drive Motor and Pinion Replacement ....................................... 9-4

Creeper-Drive Pinion Shaft Replacement ........................................... 9-5

Creeper-Drive Bull Gear Replacement ............................................. 9-5

Creeper-Drive Housing Support Mount Replacement .................................. 9-7

TransmissionOutput-ShaftSealReplacement ....................................... 9-7

ENGINE,RADIATOR,ANDMOUNTS................................................ 9-8

Radiator Upper Mount Replacement ............................................... 9-8

Radiator and Lower Radiator Mount Replacement .................................... 9-9

EngineReplacement ........................................................... 9-9

HAMMERWEIGHTREPLACEMENT ............................................... 9-12

LEADREPLACEMENT .......................................................... 9-12

SIDESHIFTCARRIAGEREPLACEMENT............................................ 9-14

CROSS-SLIDE BEARING BLOCK REPLACEMENT .................................... 9-14

HAMMERWEIGHTSHIM-KITINSTALLATION........................................ 9-16

5000054 05/07

Page i-2

Hydraulic System

................................................10-1

PUMPSANDGEARMOTORS ..................................................... 10-1

HAMMERVALVE............................................................... 10-1

Valve-Spool Seals and Servo-Valve Assembly Replacement ........................... 10-1

Hammer Relief Valve and Seat Replacement ....................................... 10-3

Load Check Valve Replacement ................................................. 10-3

CONTROL-CIRCUIT RELIEF VALVE ............................................... 10-4

HAMMER-CIRCUIT RELIEF VALVE ................................................ 10-4

PILOT-SYSTEM ROTARY VALVE .................................................. 10-5

CREEPER-CONTROL VALVE ..................................................... 10-7

CREEPER-BYPASS VALVE ...................................................... 10-8

CUSHIONVALVE(crossoverrelief)................................................. 10-9

AUTO-MANUALVALVE......................................................... 10-10

FUNCTION-CONTROL VALVES (other than auto-manual) .............................. 10-13

PILOT-VALVE ASSEMBLY (electronic stroke only) .................................... 10-13

FLOWDIVIDER(priorityvalve) ................................................... 10-14

SIDESHIFTMOTORANDSPROCKETREPLACEMENT............................... 10-16

LAYBACK CYLINDER .......................................................... 10-17

TILTCYLINDER............................................................... 10-19

STROKE-ADJUSTANDCABLE-ADJUSTCYLINDERS ................................ 10-19

HAMMERLIFTCYLINDER(automaticcylinder) ...................................... 10-22

HYDRAULIC DIAGRAM (mechanical stroke) ........................................ 10-31

HYDRAULICDIAGRAM(electronicstroke) ......................................... 10-32

Electrical System

................................................11-1

ELECTRONICCONTROLSTATION................................................ 11-1

ElectronicControlStationReplacement ........................................... 11-1

ProximitySensor ............................................................. 11-1

ELECTRICAL DIAGRAM (firewall gauges) ........................................... 11-2

ELECTRICAL DIAGRAM (front panel gauges) ........................................ 11-4

Trouble Shooting

................................................12-1

General Trouble Shooting charts ................................................. 12-1

ELECTRONICSTROKECONTROLTROUBLESHOOTING ............................. 12-8

General .................................................................... 12-8

SensorProblems............................................................. 12-8

ReplacingtheSensor ......................................................... 12-8

Voltage Check ............................................................... 12-8

Electronic Stroke Control Trouble Shooting Chart .................................... 12-9

Solenoid Valve .............................................................. 12-11

ValveSwitch ............................................................... 12-11

ElectronicControlStation ..................................................... 12-11

Stroke Length Control ........................................................ 12-11

GovernorSetting ............................................................ 12-11

PartsListing ............................................................... 12-12

5000054 05/07

Page i-3

Table III - Bolt and Cap Screw Torque Specifications

MATERIAL

SPEC

AND

MARKING

Hex Head Bolts & Hex Head Cap Screws Socket Head Cap Screws

SAE Grade 2

ASTM A307

(No Mark)

Grade 5*

ASTM A449 Grade 8*

ASTM A354 Grade 8 **

* Manufacturer’s marks may vary

** For Flat and Button Head Socket Cap Screws, use Grade 5 minimum recommended torque values.

Size

(Inches)

Grade 2

Recommended Torque*** Grade 5

Recommended Torque*** Grade 8

Recommended Torque***

lb-ft

Min. Max. NCm

Min. Max. lb-ft

Min. Max. NCm

Min. Max. lb-ft

Min. Max. NCm

Min. Max.

1/4 5 6 6.8 8.1 9 11 12.2 14.9 12 15 16.3 20.3

5/16 10 12 13.6 16.3 17 21 23.1 28.5 24 29 32.5 39.3

3/8 20 23 27 31 35 42 48 57 45 54 61 73

7/16 30 35 41 47 54 64 73 87 70 85 95 115

1/2 45 52 61 70 80 96 108 130 110 125 149 170

9/16 65 75 88 102 110 125 149 170 160 175 217 237

5/8 95 105 129 142 150 175 203 237 220 245 298 332

3/4 150 185 203 251 270 300 366 407 380 425 515 576

7/8 160 200 217 271 400 450 542 610 600 660 814 895

1 250 300 339 406 580 680 786 922 900 990 1220 1342

1-1/8 800 175 1085 1193 1280 1440 1736 1953

1-1/4 1120 1240 1519 1681 1820 2000 2468 2712

1-3/8 1460 1635 1980 2217 2380 2720 3227 3688

1-1/2 1940 2180 2631 2956 3160 3560 4285 4827

*** Use minimum recommended torque value when threads are coated with a lubricant, such as engine oil,

or fasteners with phosphate and oil coatings. Use maximum recommended torque value for dry fasteners

or zinc plated fasteners without any lubricant.

Notes: 1. This specification is intended to be a general guideline for coarse threaded hardware in ferrous

materials (steel, cast-iron).

2. Thread engagements in non-ferrous materials (aluminum, brass, plastic, etc.) may not be

adequate to allow torque specified above.

3. Where a particular application gives specific torque values, use them in lieu of those given

above. Table i-2 -Wheel Lug Nut Torque Specifications

Steering Axle Drive Axle

1/2"-20 Thread 70-90 lb-ft (95-122 NCm) 5/8"-18 Thread 175-225 lb-ft (238-306 NCm)

9/16"-18 Thread 110-140 lb-ft (150-190 NCm) 3/4"-16 single cap nut 450-500 lb-ft (612-680 NCm)

5/8"-18 Thread 175-225 lb-ft (238-306 NCm) 3/4"-16 inner cap nut 450-500 lb-ft (612-680 NCm)

1-1/8"-16 outer cap nut 450-500 lb-ft (612-680 NCm)

Adjustments - Page 7-1

5000054 05/07

Adjustments

CABLE LENGTH

In order to account for differences in the length of certain tools it may be necessary to make adjustments to the

length of the cable.* Refer to Figure 7-1 and use the following procedure when adjusting the cable:

1. Move the auto-manual control valve handle forward to the manual/start position and set the parking brake.

2. Start the engine and raise the lead to the vertical position with the layback control. Move the lead all the

way to the right-hand side of the slide using the sideshift control.

3. Lower the tool to the ground or flat surface by pushing forward on the hammer control valve handle. Shut

the engine off.

4. Loosen the cable wedge at the hammer weight or at the base of the lift cylinder. (Refer to Figure 7-1)

5. Start the engine and use the hammer control valve handle to carefully extend the lift cylinder upward 10

inches (25 cm) above the bottom of the stroke. Shut the engine off.

6. Pull the slack out of the cable and resecure the wedge(s).

7. Restart the engine and use the hammer control valve handle to carefully extend the lift cylinder to its

maximum length. The weight should stop no closer than 6-10 inches (15 - 25 cm) from the stop blocks

located near the top of the lead. Readjust the cable, if necessary, to obtain the correct gap.

If the cable length is too short, or improperly set, it may be possible to adjust the lift height

so that the weight strikes the upper travel limit stop blocks on the lead. Striking the travel

limit stop blocks can cause severe structural damage to the machine. Make sure that the

lift height and cable length are properly set to prevent damage to the machine.

* When the Arrow hammer is shipped from the factory, the cable length has been set for use with a short tool

such as a breaker or a scoring tool. If a longer tool is to be used, it may be necessary to shorten the cable setting

as described above. On mechanically adjusted units, the automatic trip fingers will not be in the proper

position in relationship to hammer stroke unless cable length is properly adjusted. The cable length must be

set long enough to enable the hammer to strike a full blow before starting the up stroke. Too long a cable will

result in a time lag between strokes. Minor changes in cable length can be accounted for without making

physical changes to the cable setting by adjusting the mechanical up and down limit trips on mechanically

actuated units. Machine equipped with electronic stroke control are self-compensating for minor changes in

cable length.

REPLACING THE CABLE

Inspect the cable daily. If the cable is badly worn, bent, kinked, or has broken wires or strands, it must be

replaced. The Arrow Hammer is equipped with either a one-piece cable or a cable spool. A one-piece cable

will require replacement whenever the cable is broken, damaged, or frayed. The cable spool, which holds 250

ft. (76 m) of spare cable, permits replacement of the broken or damaged section only.

Cable Spool - Refer to the following instructions and Figure 7-1.

NOTE: When carrying spare cable, Do not cut the cable between the cable spool and the lift cylinder. Cable

fraying usually starts near the end of the cable closest to the weight. Leaving the cable intact makes it possible

to feed only as much cable as needed to replace the damaged section. Using this procedure, insures the most

efficient use of the cable on the cable spool.

Page 7-2 - Adjustments

5000054 8/96

Figure 7-1

CABLE THREADING

Adjustments - Page 7-3

5000054 05/98

REPLACING THE CABLE - Cable Spool cont'd.

1. Lock the hammer weight (See Figure 5-3) and lay the lead back into the stowed transport position. Shut

the engine off and set the parking brake.

NOTE: If the cable has broken during operation, it will not be possible to raise and lock the hammer weight.

DO NOT attempt to lay the lead back with the hammer weight on the ground. Retract the lift cylinder

completely and temporarily re-attach the broken cable end to the hammer weight. Lift and lock the hammer

weight in place before proceeding.

2. Remove both cable wedges and the cable clamp. Remove the broken or damaged section of cable.

3. Loosen the cable spool nut and rethread the cable as needed (refer to Figure 7-1). Make sure the cable

is threaded inside the two retaining loops on the attachment bracket.

4. Thread the cable back through the hammer weight. Reinstall the cable wedge and cable clamp.

NOTE: When replacing a section of damaged cable, pull the cable through the hammer weight until the

damaged section is clear of the cable wedge when reinstalled. Cut and discard the damaged section.

5. Follow the procedure for adjusting the CABLE LENGTH to complete the installation. Be sure to retighten

the spool nut before resuming operation.

Short Cable - 51' (15.5 m) Minimum - Refer to the following instructions and Figure 7-1.

1. Lock the hammer weight (See Figure 5-3) and lay the lead back into the stowed transport position. Shut

the engine off and set the parking brake.

NOTE: If the cable has broken during operation, it will not be possible to raise and lock the hammer weight.

DO NOT attempt to lay the lead back with the hammer weight on the ground. Retract the lift cylinder

completely and temporarily re-attach the broken cable end to the hammer weight. Lift and lock the hammer

weight in place before proceeding.

2. Remove both cable wedges (Refer to Figure 7-1).

3. Remove the broken or damaged cable. Be sure to remove and retain the cable clamp.

4. Insert the end of the new cable at the base of the lift cylinder and reinstall the cable wedge (Refer to Figure

7-1).

5. Thread the cable through the sheaves in the lift cylinder as shown in Figure 7-1. Make sure that the cable

is threaded inside the two retaining loops on the attachment bracket (Refer to Figure 7-1).

6. Run the cable through the sheave at the top of the lead and back down to the weight.

7. Reinstall the cable wedge and the cable clamp at the hammer weight.

8. Follow the procedure for adjusting the CABLE LENGTH to complete the installation.

Refer to the "Specifications" section for proper cable specifications. Minimum length for the cable is 51 ft.

(15.5 m). Replacement part numbers: 4001024 - 51 ft. (15.5 m), 2000616 - 250 ft. (76 m)

Page 7-4 - Adjustments

5000054 05/07

Figure 7-2

CARRIAGE & CENTER PIN ADJUSTMENTS

5000054 05/07

Adjustments - Page 7-5

5000054 05/07

CROSS-SLIDE BEARING ADJUSTMENT

The carriage assembly is equipped with plastic slider bearings which operate in contact with the surfaces of

the sideshift ways. It will occasionally be necessary to adjust these bearings for wear. (Refer to Figure 7-2)

1. Using the layback control valve, raise the lead into a vertical position.

2. Using the sideshift control valve, move the carriage assembly to a position approximately 3 inches (8 cm)

from the extreme right hand end of its travel.

3. Loosen, but DO NOT REMOVE, the bolts that attach the lower bearing retainer to the carriage assembly.

(Refer to Figure 7-2)

Removal of the bottom guide will allow the lead and carriage assembly to tip off the

sideshift frame in any direction. Do not remove the bottom guide unless the top of

the lead has been properly secured such as to an overhead hoist or crane.

4. Loosen the jam nuts from the adjustment screws located at the bottom of the carriage assembly.

5. Turn the adjustment screws to obtain a running clearance of 0.005" to 0.020" (0.127 - 0.508 mm) at the

lower bearing. (Refer to Figure 7-2)

6. Retighten the jam nuts and the mounting bolts.

7. Clean the sideshift ways and apply fresh lubricant to the slide contact surfaces of the ways.

8. Check the sideshift mechanism for freedom of movement by shifting the mechanism from side to side.

9. Readjust to provide greater bearing clearance as required for freedom of movement.

CARRIAGE BEARING END PLAY

The center pivot bearing on the carriage assembly should be checked periodically for end play. To adjust the

end play, refer to Figure 7-2 and use the following procedure:

1. Lay the lead down onto the lead rest and shut the engine off.

2. Move the layback control valve lever both directions to relieve any cylinder pressure.

3. Using standard feeler gauges, check the end play between the thrust washer and the retaining ring at the

back of the carriage center pivot. (Refer to Figure 7-2)

4. The correct end play is 0.005" to 0.010" (0.127 - 0.254 mm).

5. Loosen the lock bolt on the retaining ring.

6. Turn the retaining ring clockwise to reduce the end play.

7. Retighten the lock bolt.

Page 7-6 - Adjustments

5000054 05/07

Figure 7-3

SIDESHIFT CHAIN ADJUSTMENT

SIDESHIFT CHAIN

To adjust the tension on the sideshift drive chain, refer to Figure 7-3 and the following procedures:

1. Using the layback control valve, raise the lead into an upright position.

2. Using the sideshift control valve, move the carriage until it is approximately 3 inches (8 cm) away

from the right hand travel limit.

3. Loosen the jam nuts on each of the two chain adjustment screws located at the rear of the carriage,

near the center pivot. (Refer to Figure 7-3)

4. Adjust both screws equally until the slack has been removed from the chain.

Do not over tighten the sideshift chain. Over tightening will lead to excess wear and

possible failure of he chain and chain drive components.

5. To check for proper chain tension, locate the approximate center of the chain span. Grasp two adjacent

strands of the chain between thumb and forefinger. It should be easy to deflect each chain approximately

1 inch (2.5 cm), but difficult to make the chains touch.

6. Retighten the nuts and the jam nuts on the chain tensioning screws.

Altri manuali per 1350

Indice

Altri manuali Arrow Master Utensili

Arrow Master

Arrow Master 1350 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare