BGS technic 6667 Manuale utente

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

BGS 6667

Clutch Aligning Tool Set for Trucks

TOOLS

1 Centering mandrel (clutch disc), 42 - 52 mm

2 Centering mandrel (clutch disc), 36 - 45 mm

3 Centering sleeve (pilot bearing), 30 mm

4 Centering sleeve (pilot bearing), 27 mm

5 Centering sleeve (pilot bearing), 25 mm

6 Centering sleeve (pilot bearing), 20 mm

7 Replacement O-rings

INTENDED USE

This tool set is required when replacing truck single and double clutch discs and allows a professional

centering of clutch discs.

SAFETY INFORMATIONS

•Read carefully the instructions before working with this tool set.

•Do not use this tool set for other purpose for which it is designed.

•Observe the general safety instructions for garages.

•Keep your work area tidy and clean. Areas or corridors which are untidy increase the risk of injury.

•Lifting of vehicles only allowed on the special lifting points.

•Before starting the work under a vehicle always ensure that it is adequately supported by axle

stands or ramps. Chock wheels and ensure that the hand brake is firmly applied.

•Always use approved eye protection, especially when working under vehicles.

•Ensure a secure and well-gripped stance during fitting.

•Check the condition of the tool regularly and do not use it if it is damaged.

•Make sure the tool is properly mounted.

•This manual serves as a brief guide and does not replace a workshop manual. Always refer to the

vehicle-specific service literature, particularly the technical data such as torque values and

instructions for disassembly/assembly, etc..

•Keep children and other unauthorized persons away from the work area.

•Do not let children play with the tool or its packaging and keep this tool out of the reach of

children.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

USE

Choose a suitable centring sleeve (3 - 6), it must fit in the

crankshaft bore / pilot bearing.

Choose a suitable centring mandrel (1 / 2) and install the

centring sleeve (3 - 6) onto the thread of the centring mandrel.

Insert the clutch centring mandrel into the clutch hub and fix

the centring mandrel in the clutch hub by turning the knurled

screw clockwise.

Centre the clutch disc with centring sleeve in the crankshaft

bore (pilot bearing) and install the clutch pressure plate.

Attention: Make sure that the clutch disc is mounted in the

proper position.

Loosen the centring mandrel by turning the knurled screw anti-

clockwise and remove it from the clutch hub.

Indice

Altri manuali BGS technic Utensili

BGS technic

BGS technic 9498 Manuale utente

BGS technic

BGS technic 8302 Manuale utente

BGS technic

BGS technic 8651 Manuale utente

BGS technic

BGS technic 50440 Manuale utente

BGS technic

BGS technic 8746 Manuale utente

BGS technic

BGS technic 66525 Manuale utente

BGS technic

BGS technic 6643 Manuale utente

BGS technic

BGS technic 8156 Manuale utente

BGS technic

BGS technic 8261 Manuale utente

BGS technic

BGS technic Drive Manuale utente

BGS technic

BGS technic 8558 Manuale utente

BGS technic

BGS technic 70114 Manuale utente

BGS technic

BGS technic 8743 Manuale utente

BGS technic

BGS technic BGS 18087 Manuale utente

BGS technic

BGS technic 1833 Manuale utente

BGS technic

BGS technic 9584 Manuale utente

BGS technic

BGS technic 8776 Manuale utente

BGS technic

BGS technic 18087 Manuale utente

BGS technic

BGS technic 8595 Manuale utente

BGS technic

BGS technic 67305 Manuale utente

BGS technic

BGS technic 8867 Manuale utente

BGS technic

BGS technic 1899 Manuale utente

BGS technic

BGS technic 8492 Manuale utente

BGS technic

BGS technic 1943 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare

Goobay

Goobay 97790 Manuale utente