BGS technic 9088 Manuale utente

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

BGS 9088

Tool Tray 1/3:

Assembly Tool Set

for Parking Sensor Holders

INTENDED USE

The assembly kit is used to replace defective parking sensor brackets or to punch holes in

unprepared plastic bumpers. Handle the tools with care and carefully clean the bracket and locator

pin after use. Lightly grease the screws and threads in the hole punches before use. Please do not

use any kind of air tools to pull the hole punches. Use the hole punches solely on plastics. Using it in

other materials such as metals will destroy the hole punch.

CONTENTS

Hole punch Ø 18.2 mm

Hole punch Ø 26.0 mm

Locator pin, red

Locator pin, silver

Holding fixture, 4 pcs.

HSS twist drill Ø 10.2 mm

USE

Many plastic bumper providers only offer a version

without parking assistance. As a result, the holes for the

parking sensors are often missing in the new plastic

bumpers. They have to be made first. First check to see

of the positions of the parking sensors are marked on the

plastic bumper. If not, find the positions with the aid of the

repair manual from the vehicle manufacturer or the

plastic bumper manufacturer. The positioning could looks

like shown in figure.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

First drill a hole in the centre of the circle.

Use the bracket you want to install to choose the correct hole punch. Position them as shown in

figure.

Turn the screw with an appropriate tool and make sure that the counter-piece of the hole punch

does not turn on the outside.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

INSTALLING A BRACKET WITH ADHESIVE TAPE

Some parking sensor brackets come with very strong adhesive tape. Use a locator pin to precisely

position and glue it on. Before installation, please thoroughly clean and degrease the adhesive

point. Please remember to paint the bracket / sensors before installation if applicable.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

INSTALLING A BRACKET WITH AN ADHESIVE SUBSTANCE

Many brackets have to be glued to the inside of the plastic bumper. Before you start gluing the

bracket, please first drill and press all required holes in the plastic bumper. Please refer to the

vehicle manufacturer’s information to find out which adhesive substance you should use. Use the

holding fixture. Assemble them as shown in figure below.

Please apply a sufficient amount of adhesive substance to the intended point on the bracket. Then

position the bracket as shown in figure. Permanent fixing is achieved with the black clamp fitting

and a knurled nut. After curing, please dismantle the holding fixture and remove any glue remnants

from it.

Indice

Altri manuali BGS technic Utensili

BGS technic

BGS technic 1987 Manuale utente

BGS technic

BGS technic 3229 Manuale utente

BGS technic

BGS technic BGS 1924 Manuale utente

BGS technic

BGS technic BGS 9071 Manuale utente

BGS technic

BGS technic 8558 Manuale utente

BGS technic

BGS technic 8690 Manuale utente

BGS technic

BGS technic 9530 Manuale utente

BGS technic

BGS technic 7744 Manuale utente

BGS technic

BGS technic 3327 Manuale utente

BGS technic

BGS technic 9862 Manuale utente

BGS technic

BGS technic 9739 Manuale utente

BGS technic

BGS technic BGS 9086 Manuale utente

BGS technic

BGS technic 3650 Manuale utente

BGS technic

BGS technic 3361 Manuale utente

BGS technic

BGS technic BGS 70009 Manuale utente

BGS technic

BGS technic 62607 Manuale utente

BGS technic

BGS technic 8766 Manuale utente

BGS technic

BGS technic BGS 7710 Manuale utente

BGS technic

BGS technic 6743 Manuale utente

BGS technic

BGS technic 66205 Manuale utente

BGS technic

BGS technic 8776 Manuale utente

BGS technic

BGS technic 1246 Manuale utente

BGS technic

BGS technic 6650 Manuale utente

BGS technic

BGS technic 62625 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare

Goobay

Goobay 97790 Manuale utente