Ensure that the correct
combination of Barrel and
fasteners are used.
Check and replace the worn-
out parts if necessary.
Clean all the parts of the tool.
If the problem persists, DO
NOT use the tool . Have the
tool checked / repaired by a
Bluepoint professional.
SAFETY PRECAUTION
Do not straighten your arms while
firing the tool. Keep them flexed.
Never leave the loaded tool
unattended.
Ensure that the tool is not loaded
before servicing, cleaning or
replacing parts and before storing it.
Always Nitro Ninja Fasteners and
unused tools unloaded, in a dry
location, and in a high or locked
place, out of children’s reach.
6. Temperature
Do not dismantle the tool when it is
hot.
Never exceed the recommended
maximum fastener driving rate. (500
fastenings / hour).
7. Requirements to be met by users
(Pre-requisites for users)
Only authorized, trained
professionals should operate,
service, and repair the tool. The
professional must be informed of
any special hazards that may be
encountered.
Operate the tool only if your full
attention is on the job.
Do not use the tool if you feel
unwell.
8. Personal Protective Equipment
(PPE)
The operator and all other
bystanders must always wear eye
and ear protection and a hard hat.
Prior to use
9. Read the Instruction Manual
carefully.
10. Inspection of tool
Ensure that the tool is not loaded.
Routinely check the tool for damage
and ensure that all controls operate
properly.
11. Selection of the correct Barrel /
fasteners combination
Using the wrong combination may
result in damage to the tool and / or
affect fastening quality.
0504
1. General Safety Instructions
The following points must be
strictly observed at all times, in
addition to the specific safety
precautions listed in the individual
sections.
2. Use as recommended
The tool is designed for use only by
professionals in the construction
industry for fastening applications
where drive pins or composite
fasteners are driven into steel,
concrete or sand-lime block
masonry.
3. Inappropriate use
Modification or manipulation of the
tool is not permitted.
Unless the tool is approved for such
use, it should not be used in a
flammable or an explosive
environment.
Use only BLUEPOINT fasteners,
accessories or spare parts of
equivalent quality to avoid risk of
injury.
Strictly follow the instructions for
operation, care and maintenance
given in the Instruction Manual.
The tool should never be pointed at
self or any bystander.
The muzzle of the tool should never
be pressed against a hand or any
body part.
The nails are NOT to be driven into
materials such as marble, natural
rock, glass, copper, brass, bonze,
plastic, insulation materials,
hollow brick, glazed tile, thin sheet
metal (<4 mm), grey cast iron,
spheroidal cast iron or gas
concrete.
The tool and its accessories may be
hazardous if used improperly by an
unauthorized person.
4. Workplace safety
Avoid unergonomic body postures.
Hazardous objects should be
removed from the work area.
Other bystanders, particularly
children, should not be allowed in
the work area.
Make sure nobody is behind or
below the point where the fastener
is to be driven.
The tool grip should always be kept
free of oil or grease.
5. Basic safety precautions
Operate the tool only in good
condition and only as directed.
Use the spall guard when required.
If the Nitro Ninja Fasteners fails to
ignite or misfires, please do the
following:
Hold the tool pressed against
the working surface for 30
seconds.
If the Nitro Ninja Fasteners still
fails to fire, withdraw the tool
from the working surface
making sure it is not pointed
towards anybody or yourself.
Then carefully open the tool,
remove the Nitro Ninja
Fasteners and put it in a can of
water or other non-flammable
liquid. Never discard the Nitro
Ninja Fasteners into a
dumpster.
If 2-3 Nitro Ninja Fasteners misfire
in succession (without making any
audible firing noise and if the
fastener is driven with significantly
less force), do the following:
Immediately STOP using the
tool.
Dismantle the tool.
SAFETY PRECAUTION
