Canon AE-1 Guida di riferimento

FINISHER-AE1

SADDLE FINISHER-AE2

PUNCHER UNIT-LIIMIINIIPI

INSTALLATION PROCEDURE

Follow the instructionshereinwhen installingthe Productto its host machine.

~%&~~4$~Z#3?~~5~13,

UTD?FJIR~Z@T

b\o

PUB. F-IM-6673-000 PRINTED

JAPAN

CHINA

Page References for Installation

When installingthe finisherandthepuncherunit,first install thebuffer path andunpackthe finisher

(P.3

P.12),

and

then install them according to the following installation instructions.

When installing only the finisher: see

P.12.

When installing the finisherand puncher unit at the same time: see

P.23.

When installingthepuncherunit afterhaving installedthefinisher:After followingtheprocedure for installingonly

the finisher

(P.12

P.22),

seepage

P.36.

1.2

Making

Pre-Checks

1.2.1

Checkingthe Contents

Finisher-AElISaddle Finisher-AE2

Before installing the host machine, confirmthat the 3-Way Unit-A1 isinstalled. The 3 Way Unit-A1 comes intwo

types depending on the model: either as standard equipment or as an option.

[I]

Fixingplate

[2]

Fixing plate

[5]

Staple cartridge

[7]

Front foot cover

[3]

Fixing plate

[4]

Fixing plate

box

pcs.)

[5]

Staple cartridge

[6]

Cartridge for saddle

PC.

[7]

Front foot cover

PC.

box

pcs.)

box

pcs.)

PC.

[8]

Front lower extension cover

pc.

[8]

Front lower extension cover

[9]

Front lower extension stay

[lo]

Caster cover

Groundrail

PC.

Groundrail

[12]

Screw(RStightening;

8) 2

pcs.

[12]

Screw(RStightening;

[13]

Screw (binding;

6) 6

pcs.

[13]

Screw(binding;

[14]

Screw(tapping;

12)

[15]

Stepped screw

(M4) 2

pcs.

[15]

Steppedscrew

(M4)

[16]

Tray label

sheet

[16]

Tray label

[17]

Settingslabel

sheet

[17]

Settingslabel

[18]

Bookmakinglabel

[19]

Rear foot cover

Buffer

Pass Unit-E2

[I]

Bufferpass unit

PC.

[2]

Screw (tapping;

12) 2

pcs.

[3]

Rubber sheet

PC.

[4]

Blankingplate*1

PC.

[5]

Screw (binding;

6)*l

pcs.

PC.

1PC.

PC.

pcs.

1sheet

sheet

1 sheet

PC.

*':

This part is used when only the finisher is installed. It is not used when a puncher unit is installed.

Puncher

Unit-Ll/Ml/Nl/Pl

[I] Punchfrontlower cover 1PC. [8] Surfacecover 1PC.

[2] Punch frontlowerextensioncover 1pc. [9] Mountingstepped screw (M4X4) 2 pcs.

[3] Punchfront lower cover fixingplate 1 1pc. [lo] Steppedscrew (M4X5) 2 pcs.

[4] Punchfront lower cover fixingplate 2 1pc.*l [l11 Steppedscrew (M4X10)

pcs.

[5] PunchJam Removal label

PC. [12] Screw(binding;M4X6) 5pcs.*2

[6]

Punchfixingplate (front)

PC. [13] Screw (tapping; M4X2) 3 pcs.

[7] Punch fixingplate (rear) 1PC.

Only forthe Finisher-AEl

*2: 4 pc. used if for the SaddleFinisher-AE2.

.2.2

Installingthe Accessories

If you are installingaccessoriesat the sametime as you are installingthis product, installthe host machine first and

then the accessoriesin the followingsequence:

1. Side paper deck (See its InstallationProcedure.)

2. Installationof the buffer pass unit [I]

3. Finisher-AE1 [2], SaddleFinisher-AE2 [3]

Puncherunit

[4]

Connectionto the host machine

Turning Off the Main Power of the Host Machine

When turning off the main power, be sure to go throughthe followingin strict sequence to protect the machine's

hard disk:

[l]

Hold on the power switchon the controlpanel 3 sec or more.

[2]Operateon the touchpanel accordingto the shut-downsequenceindicatedsothat the main power switchmay

be turned off.

[3]Turn off the main power switch.

[4]

Disconnect the power cable (for the power outlet).

1.2.3

Selectingthe Site of Installation

Selectthe siteof installation,making suretherewill be enough space for work (e.g.,removal of paper). Be sure also

that there will be no gap between the finisher and the host machine.

<Finisher-AEl>

100

or more

unit:

F-1-5

--------...

----------------......-----------

unit:

F-1-6

Be sure to install the host machine and the finisher on a level surfacewithout any step or gap. Otherwise,faults

associated with paper movement can occur.

1.3

Installingthe Buffer

5) Remove allpacking tape from the buffer pass unit.

Place the buffer pass unit on the delivery tray, and

Pass Unit

connectthe connector [l]to the host machine.

Match the claw of the buffer pass unit against the

1) Detach the blanking part [I]from the rear internal connectingassembly [2],and securethebuffer pass

cover and the blankingpart [2]of the delivery tray, unit in place using two screws [3] (tapping; M4 x

by disengaging the claw using a flat-blade screw- 12).

driver.

2) Detach the blanking part [3] using a flat-blade

screwdriver or the like.

3) Remove the paper full sensor flag [4] for delivery

tray 1.

Do not remove the paper full sensorflag [5]forde-

livery tray 2.

4) Remove the paper full sensor flag for delivery tray

1,and then attach the cover [3].

When the cover [3] is not attached, remove the fol-

lowing parts:

Host machine's front cover (one blanking rubber

and two screws)

Host machine's deliverytray (two screws)

Host machine's rear cover (four screws)

Next, remove the paper full sensor flag [4] for de-

liverytray

and then attach the cover in place.

When installingthe buffer pass unit, take care not

to break

[4]

of the sensor flag for delivery tray

1.4

Unpacking and Checking

the Components

1.4.1

Unpacking (Finisher)

MEMO:

The machine is packed using tape and cushioning

materials to be protected against vibration and

shock during transit. Be sure to remove them be-

fore starting to install the machine. (It is a good

idea to store away the removed tape and cushion-

ingmaterialforpossiblerelocationofthemachine,

e.g.,to a new site or for repairs.)

Take out the accessorybox from the shippingbox.

2) Lift the finisher together with its cushioning base

(Styrofoam).Be sureto work in a group oftwo per-

sons.

If you shiftup the finisher on its side,you would

likelydeform or damage the machine.Moreover,

in the case of the SaddleFinisher-AE2,the force

applied to the front cover [l] can deform the

hinge.

The finisher is rather heavy. (Weight: Finisher-

AE1: 43.2 kg, SaddleFinisher-AE2:73.2 kg) Be

sure to work in a group of two persons. Particu-

larly when moving it over a step on the floor, be

sure to take full care not to let it tumble over.

At this point, do not remove the four cushioning

materials (Styrofoam)fromthe finisher.Otherwise,

you would likely deform some areas of the ma-

chine.

3) Remove the cushioningmaterial (Styrofoam)from

the upper cover.

Slightly lift the front and rear casters, and remove

the cushioning material (Styrofoam). Be sure to

shiftup the finisherby holding the upper left cover

(gray area).

F-I

-1

Takethe finisherout ofthebag andremovethetape

Remove the two fixing screws [I],and remove the

used outsidethe finisher. 2 tray fixings [2].

For the Saddle Finisher-AE2, do not peel off the

blind seal [I]from the saddletray.

[?I

F-1-12

Inthe case ofthe Finisher-AEl, openthe front door

[I]. In the case of the Saddle Finisher-AE2, open

the front cover [2].

Remove the cushioningmaterial [I](Styrofoam)of <SaddleFinisher-AE2>

the tray.

Altri manuali per AE-1

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Canon Accessori per stampanti

Canon

Canon DADF-H1 Manuale utente

Canon

Canon Color Network UFR Printer Kit-C1 Manuale utente

Canon

Canon Stacker-C1 Manuale utente

Canon

Canon High Capacity Stacker-G1 Manuale utente

Canon

Canon Multi Function Professional Puncher-A1 Manuale utente

Canon

Canon Puncher Unit-N1 Manuale di servizio

Canon

Canon INNER 2-WAY TRAY-E1 Manuale operativo e di manutenzione

Canon

Canon Puncher Unit-L1 Manuale utente

Canon

Canon Cassette Feeding Unit-AM1 Manuale utente

Canon

Canon E3730A Manuale utente

Canon

Canon Inner 2 Way Tray-E1 Manuale utente

Canon

Canon Puncher Unit-P1 Manuale utente

Canon

Canon Multi-PDL Printer Kit-E1 Manuale utente

Canon

Canon 2/3 Hole Puncher Unit-A1 Manuale utente

Canon

Canon AD2 Manuale utente

Canon

Canon Puncher Unit-BF1 Manuale utente

Canon

Canon Super G3 2nd Line FAX Board-AM1 Manuale utente

Canon

Canon DADF-N1 Manuale utente

Canon

Canon Enhanced Color Copy 216GSM Guida di riferimento rapido

Canon

Canon imagePROGRAF RU-42 Manuale utente

Canon

Canon NP6330 Come usare

Canon

Canon Finisher-T1 Manuale utente

Canon

Canon Color iR Security Kit-A1P Manuale utente

Canon

Canon Finisher-R1 Manuale operativo e di manutenzione

Manuali Accessori per stampanti popolari di altre marche

Star Micronics

Star Micronics TSP800 Series Manuale utente

REA

REA JET HR pro 2K Manuale utente

HP Laserjet,Color Laserjet 4si Manuale utente

oliser

oliser MS 45 Manuale utente

Roland

Roland DU2-64 Istruzioni e ricette

Xerox

Xerox EFI EXP6000 Manuale utente

Sharp

Sharp FO-1MK Manuale utente

Labelmate

Labelmate PM-300 Manuale utente

Epson

Epson T6248 Manuale operativo

Epson

Epson OT-BZ20 Manuale utente

Ricoh

Ricoh LCIT RT5100 Guida rapida

GBC

GBC 16 Series Manuale utente

Develop

Develop SD-509 Manuale utente

Kyocera

Kyocera KM-6230 Manuale

Triumph Adler

Triumph Adler DF-710 Manuale

Citizen

Citizen CBM-202PC Series Manuale utente

Codonics

Codonics Virtua 1VCX-LR833 Guida di riferimento

TonerRefillKits

TonerRefillKits ReChargX RX126 Manuale utente