CYP CMSDI-1616S Manuale utente
CMSDI-1616S
16×16 3G-SDI Hybrid Modular Matrix
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if it is
damaged.
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 21/01/13 Preliminary Release
VS1 11/03/13 Updated format/diagrams
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................5
6.3. Remote Control...............................6
6.4 RS-232 Protocols ...............................7
6.5 Assign IP Address..............................7
6.6 RS-232/Telnet Commands...............8
6.7 Telnet Control ...................................9
6.8 Web GUI Control ............................11
7. Specications ...................................... 12
8. Connection Diagram .......................... 15
9. Acronyms ............................................. 17
1
1. INTRODUCTION
This 16×16 3G-SDI Hybrid Modular Matrix can switch and distribute up
to sixteen SDI sources to any sixteen SDI sinks, providing bandwidth
up to 2.970 Gb/s for 3G-SDI video support. In addition, this matrix also
features IP control allowing users to access and control the matrix
remotely.
2. APPLICATIONS
• Video broadcasting system switching and display
• Professional video editing suite switching and display
• Film studio program monitoring
• Airport or industrial security monitoring system
3. PACKAGE CONTENTS
• 16×16 3G-SDI Hybrid Modular Matrix
• Power Cord
• Remote Control (CR-119 with Battery)
• Operation Manual
4. SYSTEM REQUIREMENTS
SDI source equipment such as an SDI camera and output SDI monitor
or recording device with recommended SDI connection cables.
2
5. FEATURES
• Supports operation at 2.970 Gb/s, 2.970/1.001 Gb/s, 1.485 Gb/s,
1.485/1.001Gb/s, and 270 Mb/s
• Supports SDI input/output modes:
- SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s)
- HD-SDI (SMPTE 292M, at bitrates of 1.485Gbit/s and 1.485/1.001 Gbit/s)
- 3G-SDI (SMPTE 424M/425M-A and B, at bitrates of 2.970 Gbit/s and
2.970/1.001 Gbit/s)
• Signal equalized and re-clocked to improve signal transmission
distances
• Supports signal input and output distances of up to 250 m for SD
signals, 200 m for HD signals and 100 m for 3G signals
• Supports audio sampling rate at 48 kHz
• Connects with other units to extend your signal over longer distances
• 3U rack mountable design
Note: The unit was tested with Belden 1694A cable, results may vary
with cables of a different specication.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWERRETURN7 89
456
LOCK
SAVE
123RECALL
0ENTER OUT/IN
MENU
ALL
+
PAGE
PAGE
STANDBY
LOCK
DIGITAL MATRIX SWITCHER
106431 9 11 12 16
137 852
15
14
1LCM: Displays the Menu and the setting information of each input
and output selection.
2STANDBY LED: This LED will illuminate when unit is in 'Stand-by
Mode'.
3LOCK LED: This LED will illuminate when the key lock function is
active.
4IR Window: IR Receiver window (accepts the remote control signal
of this device only).
5POWER: Press this button to power the device on/off.
6PAGE ▲◄►▲: Use these buttons to display the current Input/
Output settings status or to navigate the settings menu.
7RETURN: Press this button to go back/exit the current selection.
4
8MENU: Press this button to enter the settings menu. There are total
of 9 functions available.
- Firmware version
- IP Address: Use this address for logging into Telnet and the Web
GUI
- DHCP/AUTO IP ON/OFF (ON: DHCP enable, OFF: Static IP enable)
- STATIC IP
- STATIC NETMASK Setting
- STATIC GATEWAY Setting
- In Slot Info.
- Out Slot Info.
- Exit
9ENTER: Press to conrm the setting or selection.
10 0~9: Press to select the input or output ports.
11 OUT/IN: Press this button to select the which source (Input) to show
on which display (Output). Press 'OUT/IN', then select the desired
output using the number buttons (use the '+' button to add further
outputs if required or 'ALL' to assign all outputs to the same source),
then press 'OUT/IN' again to then select which source you wish
assign.
Note: Only a single source can be selected at any one time but
multiple outputs can be assigned to a source.
12 +: Press this button when selecting more than one output for a
source. (This button is only functional in when in Input/Output
entry mode)
13 LOCK: Press and hold this button for 3 seconds to lock all the front
panel buttons to prevent accidental button presses. The Lock
LED will illuminate, to unlock press and hold the button again for 3
seconds.
14 SAVE: Press this button to save the present Input/Output settings.
There are 10 sets available for saving.
15 RECALL: Press this button to recall the saved Input/Output settings
(1~10).
16 ALL: Press this button to directly assign all outputs to the same input.
5
6.2 Rear Panel
9 12
-9 12
-
13 16
-13 16
-
INPUT
100-240VAC
50/60 Hz
1 4
-
1 4
-
INPUT
5 8
-
INPUT INPUT OUTPUTOUTPUT
1 4
-
1 4
-
OUTPUT OUTPUT
5 8
-
RS232
CONTROL
12
35
4 76
1INPUT 1~16: Connect up to 16 SDI equipped source devices such
as digital cameras or video players with SDI cables.
2OUTPUT 1~16: Connect up to 16 SDI equipped sink devices such
as displays (TV/monitors) or broadcast video recorders with SDI
cables.
3RS-232: Connect to a PC or RS-232 control system with D-Sub 9-pin
cable to control the unit with RS-232 commands (See Section 6.6
for RS-232 commands).
4CONTROL: This port is the link for Telnet and Web GUI controls,
connect to an active Ethernet link with an RJ45 terminated cable
(for further details, please refer to sections 6.7 and 6.8).
5POWER Switch: Use this switch to power the device ON(I) or OFF(O),
when the power is switched ON the device will automatically
power up.
6Power Supply: Plug the power cord to an AC wall outlet for power
supply.
7Ventilation Fan: This fan will automatically activate when the
device is switched ON. Do not block or cover this port. Please
allow adequate space around the unit for air to circulate.
Indice
Altri manuali CYP Commutatore a matrice
CYP
CYP CMPRO-4H4H Manuale utente
CYP
CYP PUV-44XPL-AVLC Manuale utente
CYP
CYP OR-IR44 Manuale utente
CYP
CYP CMPRO-U8H8CVE Manuale utente
CYP
CYP CDPS-44SM Manuale utente
CYP
CYP CMSI-8H8CVE Manuale utente
CYP
CYP CMPRO-U8H8CVPL Manuale utente
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Manuale utente
CYP
CYP OR-HD88HC Manuale utente
CYP
CYP PU-O4H4C Manuale utente
CYP
CYP PRO-F32M Manuale utente
CYP
CYP EL-42M-PIP Manuale utente
CYP
CYP CPLUS-V4H2HPIP Manuale utente
CYP
CYP MA-421 Manuale utente
CYP
CYP CPLUS-V8H8HP Manuale utente
CYP
CYP CMPRO-UA8H8CVE Manuale utente
CYP
CYP PU-8H8HBTPL Manuale utente
CYP
CYP CDPS-U10H2HFS Manuale utente
CYP
CYP CPLUS-V4H2HP-DT Manuale utente
CYP
CYP PU-8H8HBTE Manuale utente
