CYP CH-U331TX Manuale utente

CH-U331TX

HDMI/VGA over IP Transmitter

with USB/KVM Extension

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

RDV1 23/02/17 Preliminary release

RDV2 20/04/17 Changed text/silkscreen

RDV3 29/08/17 Added video wall functions

VS1 12/09/17 Updated text/diagrams

VS2 01/11/17 Final technical review

VS3 11/01/18 Minor changes to the commands

VS4 05/06/18 Updated section 8.3

VS5 10/07/18 Added ISP SEL switch description

CONTENTS

1. Introduction......................................................1

2. Applications.....................................................1

3. Package Contents ..........................................2

4. System Requirements......................................2

5. Features............................................................3

6. Operation Controls and Functions.................4

6.1 Transmitter's Front Panel ........................... 4

6.2 Transmitter's Rear Panel............................ 6

6.3 IR Cable Pin Assignments ......................... 7

6.4 RS-232 Protocol.......................................... 7

6.5 Telnet Commands..................................... 8

6.6 WebGUI Control ...................................... 20

6.6.1 System Tab...................................... 21

6.6.2 Video Wall Tab ............................... 24

6.6.3 Network Tab ................................... 28

6.6.4 Functions Tab ................................. 30

7. Connection Diagram ....................................34

8. Specications ................................................35

8.1 Technical Specications ........................ 35

8.2 Video Specications............................... 36

8.3 Audio Specications............................... 37

9. Acronyms .......................................................39

1. INTRODUCTION

This unit is part of a 4K UHD Multi-Function Extension system that allows

you to extend HDMI or VGA signals along with KVM using the TCP/

IP protocol over regular Cat.5e/6/7 network cable. This extender

supports the transmission of Ultra High-Denition signals (up to 4K@30Hz

YUV 4:4:4 or 4K@60Hz YUV 4:2:0) with audio and USB up to 100m on a

single cable. The transmission distance can be further extended (up

to 100m per segment) by using gigabit network switches, allowing the

user to cascade the system without signal loss or introducing delay.

It is also possible to have the extension system's Transmitter operate

in multicast mode, allowing you to send a single AV signal to a large

number of Receivers within the same local network. Additionally, that

same multicast signal can be used to create large multi-display video

walls with amazing simplicity. This system is perfect for both residential

and commercial installation environments.

This system also features bi-directional IR and RS-232 pass-through,

analog line level in/out, and a microphone input (on the Receiver),

providing the user with a variety of audio options. The USB functionality

allows the system to act like a remote USB hub which, when combined

with the VGA input/output feature, provides a exible remote KVM

platform. Conguration information is provided via On Screen Display

(OSD) and control is by WebGUI, Telnet, and front panel controls.

2. APPLICATIONS

• HDMI, VGA, USB, Audio, IR, and RS-232 extension

• Broadcasting a system over a single Cat.5e/6 cable

• Multimedia display on a large number of displays via multicast

• Hotel or convention center display multi-monitor broadcast

• Long distance data and video transmission via cascading

• Distributed video matrix system

• Distributed video wall system

• Remote KVM control of a system

3. PACKAGE CONTENTS

• 1×HDMI/VGA over IP Transmitter with USB/KVM Extension

• 1×IR Extender Cable

• 1×IR Blaster Cable

• 1×5V/2.6A DC Power Adaptor

• 1×Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI or VGA source equipment such as media players, video

game consoles, PCs or set-top boxes.

• HDMI or VGA receiving equipment such as HDTVs, monitors or audio

ampliers.

• Analog audio receiving equipment such as headphones, audio

ampliers or powered speakers.

• A Gigabit Ethernet network switch with jumbo frame support is

required. (8K jumbo frames are strongly recommended.)

• A Gigabit Ethernet switch with “IGMP snooping” enabled is required

for multicast support.

5. FEATURES

• HDMI 2.0 and DVI 1.0 compliant

• HDCP 1.4 & 2.2 compliant

• 1×HDMI input, 1×VGA input & 1×VGA bypass output

• Video, audio and control transmission over TCP/IP in Unicast (point-

to-point) or Multicast (single-to-many) modes

• Multi-monitor video wall support with 90° rotation

• HDMI input resolutions up to 4K@60Hz (YUV 4:2:0, 8-bit) or 4K@30Hz

(YUV 4:4:4, 8-bit)

Note: 4K@50/60Hz (YUV 4:2:0) sources are automatically converted to

4K@25/30Hz (RGB) for output

• VGA input and output resolutions up to WUXGA (RB)

• Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,

and Bitstream over HDMI

Note: The optical output on Receivers can only support LPCM 2.0 &

Bitstream sources.

• The analog Line In on the Transmitter sends audio directly to the

analog Line Out and is inserted into the HDMI output on connected

Receivers

• The Mic In on the Receiver sends audio directly to the analog Line

Out on the Transmitter

• Both Tx and Rx may powered directly by PoE when connected to a

Gigabit Ethernet switch that provides PoE (802.3af)

• Supports USB keyboard, mouse and storage extension

• Supports IR and RS-232 bypass

• Unit can be controlled via WebGUI, Telnet, and front panel controls

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter's Front Panel

POWER

RS-232

ISP

SEL

OUT

RESET

IR LINK

LOOPBACK

Anti-DITHER

MODE ISP

VGA

LOOPBACK

LINK

21 3 4 5 6 7 8 9 1011 12

1POWER LED: This LED will ash while the unit is powering on and will

illuminate solidly once it is ready to be used.

2LINK LED: If the Transmitter has no network connection the LINK LED

will not illuminate. While the Transmitter is attempting to establish

a connection with a Receiver the LINK LED will ash. When the

Transmitter has established a stable connection with a Receiver

the LINK LED will illuminate solidly.

3RS-232 IN: Connect directly to your PC/laptop to send commands

to RS-232 devices connected to the Receiver. The baud rate is

congurable, but the default baud rate is 115200.

Note: When the Transmitter is in multicast mode every connected

Receiver unit can send RS-232 commands to the Transmitter

and commands sent from the Transmitter side will be sent to all

associated Receivers.

4ISP SEL: For Factory use only. By default this is set to the right (away

from the RS-232 port) and allows normal RS-232 functionality.

Setting this switch to the left enables ISP engineering mode.

5IR OUT: Connect to the provided IR Blaster to transmit IR signals sent

from the associated Receiver to devices within direct line-of-sight

of the IR Blaster.

6IR IN: Connect to the provided IR Extender to extend the IR control

range of remotely located devices. Ensure that the remote being

used is within direct line-of-sight of the IR Extender.

Note: When the Transmitter is in multicast mode the IR signal is sent

to all associated Receivers.

7IR WINDOW: Accepts IR signals from any standard remote control

and sends the signal to the IR Out on the associated Receiver.

Note: When the Transmitter is in multicast mode the IR signal is sent

to all associated Receivers.

8LOOPBACK/LINK: This button controls multiple functions:

aLoopback: Press this button momentarily to toggle the VGA

Loopback function on and off, allowing you to locally monitor non-

HDCP HDMI sources (1080p or below) for troubleshooting purposes.

bVideo Link: Press and hold the button for 3 seconds to enable or

disable the Video Link. When the link is disabled and the Receiver

is connected to a display it will show the system’s current IP and

rmware information.

cReset to Factory Defaults: Press and hold this button when

powering the unit on until both the POWER and LINK lights are

blinking. Once both lights are blinking you can reboot the unit

and all settings will be returned to the factory defaults (Including

resetting the IP mode to auto, broadcast channel to 0, and the

streaming mode to multicast). A new IP address will be assigned

automatically within the 169.254.xxx.xxx address range.

9MODE/Anti-DITHER: This button controls multiple functions:

aVideo Mode: Press this button momentarily to toggle the video

data streaming method between “Graphic” and “Video” modes.

“Graphic” mode is optimized for high-detail static displays and

“Video” mode is optimized for full motion video.

bAnti-Dither: Press and hold this button for 3 seconds to enable

and switch between the three “Anti-Dither” modes (1-bit, 2-bit

and off). Certain graphics cards use dithering to emulate a larger

color palette, but dithering causes difculty for maintaining low-

bandwidth during real-time video compression, so these Anti-

Dithering modes are designed to remove the dithering prior to

compression and transmission of the signal. If the source is not

using dithering, please leave this feature disabled as it may cause

a blocking effect with non-dithered content.

Note: This feature is set to “off” by default.

10 ISP: For factory use only.

11 RESET: Press this recessed button to reboot the unit (Settings will not

be reset).

12 VGA LOOPBACK OUT: Connect to an analog VGA monitor to

locally view the connected VGA or HDMI (non-HDCP, 1080p or

lower) source.

6.2 Transmitter's Rear Panel

DC 5V

USB VGA IN HDMI IN LINE IN LINE OUT

LAN (PoE)

2 3 4 5 6 7

1DC 5V: Plug the 5V DC power adapter into the unit and connect it

to an AC wall outlet for power. (Optional if powered by PoE)

2USB: Connect directly to a PC to extend its USB functionality to the

ports on the connected Receiver.

3LAN (PoE): Connect via a Gigabit Ethernet switch to compatible

Receiver(s) to transmit data, and to a PC/laptop to control the unit

via WebGUI.

Note: This unit can be powered directly by the connected Gigabit

Ethernet switch if it provides PoE (802.3af).

4VGA IN: Connect to VGA source equipment such as a PC or

laptop.

 Note:PCtextandcontentwithnedetailsmaydisplaywithsome

visual artifacts when transmitted at 4K@60Hz (YUV 4:2:0).

5HDMI IN: Connect to HDMI source equipment such as a media

player, game console or set-top box.

6LINE IN: Connect to the stereo analog output of a device such as

a CD player or PC.

Note: When a live audio source is connected to the Line In, it will

be automatically embedded into the transmitted signal, and will

completely replace any existing HDMI audio.

7LINE OUT: Connect to powered speakers or an amplier for stereo

analog audio output. This will output the audio from the Mic In on

the connected Receiver.

Note: This function is only available in Unicast mode. The Mic In

audio channel from the Receiver is only active when an analog

source is also connected to the Line In port on the Transmitter.

Indice

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente