CYP CHDBT-1H7CE Manuale utente

DRAFT

CHDBT-1H7CE

1 by 8 HDMI over HDMI & CAT5e/6/7 with PoE

and Ethernet Transmitter

Operation Manual

DRAFT

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.0 September 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

DRAFT

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

RDV1 26/06/13 Preliminary Release

DRAFT

CONTENTS

1. Introduction............................................1

2. Applications...........................................1

3. Package Contents ................................1

4. System Requirements............................1

5. Features..................................................2

6. Operation Controls and Functions.......3

6.1 Front Panel........................................3

6.2 Rear Panel.........................................3

6.3 IR Cable Pin Assignment..................5

7. Connection Diagram ...........................6

8. Specications ........................................7

8.1 CAT5e/6/7 Cable Specication .....8

9. Acronyms...............................................8

DRAFT

1. INTRODUCTION

The HDMI over HDMI and CAT5e/6/7 Transmitter can support

resolutions up to 1080p Full HD, 4Kx2K timing, 3D and multi-channel

digital audio formats to one HDTV and seven CAT5e/6/7 outputs.

The HDMI can be connected to HDMI display for instant nearby

display and the CAT5e/6/7 can be connected to CAT5e/6/7 to HDMI

Receivers for distance up to 100 meters. Further, a total of 100Mbps

Ethernet transmission rate allows all connected device to share the

Ethernet service and the PoE function free the power shortage issue

from the Receiver end.

2. APPLICATIONS

• Household entertainment sharing and control

• Lecture room display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• HDMI over HDMI & CAT5e/6/7 with PoE and Ethernet Transmitter

• IR Receiver x 1

• IR Blaster x 1

• 24V DC Power Adaptor

• Power Cord

• Operation Manual

4. SYSTEM REQUIREMENTS

• Source equipment with HDMI output connector

• Display TV/Monitor with HDMI input connector

• HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables

DRAFT

5. FEATURES

• HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant

• The HDMI and CAT5e/6/7 outputs are playing the same source

simultaneously

• Supports one HDTV and seven CAT5e/6/7 outputs

• Supports data rate from 250Mbps up to 3Gbps

• Supports wide range of PC resolutions from VGA to WUXGA

and HDTV resolutions up to 4Kx2K (3840x2160@30Hz and

4096x2160@24Hz)

• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD

Master Audio transmission (32-192kHz sample rate)

• Supports distances up to 100 meters through CAT5e/6/7 cables

• Supports Ethernet transmission rate up to 100Mbps

• Can select Standard or TV EDID

• Supports USB service port

• The 3D signal display follow by display TV’s EDID

• Supports PoE with capable Receiver units

• Supports Bi-directional IR control

Note:

1. This system was tested with CAT6/23AWG cables, results may vary

 withcablesofadifferentspecication.

2. The PoE function is designed for powering compatible Receiver

units only non-PoE Receivers will need their own power supply.

Receivers of another brand may not be compatible.

3. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI

cable and display in order for proper image displaying.

DRAFT

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER SYNC HDMI

LINK LINK 1LINK 2LINK 3LINK 4 LINK 5 LINK 6 LINK 7

CAT5e/6/7 OUT

1 2 3 4

1POWER LED: Once the power supply is connected the LED will

illuminate

2SYNC: This LED will illuminate when the HDMI input port connected

to the source.

3HDMI LINK: This LED will illuminate when HDMI output is connected

to TV or display monitor.

4LINK 1~7: The link LED will illuminate when CAT5e/6/7 output(s)

has been connected to the Receiver(s) and the Receiver(s) has

connected with display that shows image on screen.

6.2 Rear Panel

1HDMI OUTHDMI IN 234567LAN

SERVICE

CAT5e/6/7 OUT

STD TV

DC 24V

IR IN IR OUT

EDID

1 2 3 4 7 8 95 6

1HDMI IN: Connect with source equipment such as DVD/Blu-ray or

PS3 player.

2HDMI OUT: Connect to HDMI display for instant image display or

cascade with another family type Transmitter.

3CAT5e/6/7 OUT 1~7: Connect these ports to CAT5e/6/7 to HDMI

Receivers (with or without PoE function) with CAT5e/6/7 cable to

extend the signal up to 100m.

4LAN: Connect to intra-net or internet service system for a total

sharing rate of 100Mbps within the link of Transmitter.

Warning: DO NOT connect this slot with any of the CAT5e/6/7 port,

doing so may trigger a power shot down and ruin the device.

DRAFT

5IR IN: Connect with IR Extender to receive IR signal from Transmitter

side and blast out at Receiver side. Ensure that remote controller

being used is within the direct line-of-sight of the IR Extender.

6IR OUT: Connect with IR Blaster to blast out the IR signal received

from the Receiver side. Place the IR Blaster in direct line-of-sight of

the equipment to be controlled.

7EDID STD/TV: The default factory setting is on TV, leave as it is

when the display is properly. The unit will detect the 1st CAT5e/6/7

output’s EDID when it obtain a 4Kx2K EDID and send out the signal

accordingly to other output ports. If the 1st CAT5e/6/7 output is

without a 4Kx2K's EDID the unit will detect all output's EDID and

send out the signal that all outputs can accept.

This device obtain the last memory function therefore, the device

will use the last output port 1's EDID when output port 1 is not

connected to a display after power cycling or switch in between

the EDID setting.

Switch to STD to use build-in EDID if the display has problem. STD

EDID's video at 1080p@60Hz and audio at LPCM 2CH.

8SERVICE: This slot is reserved for factory service only.

9DC 24V: Plug the 24V DC power supply into the unit and connect

the adaptor to an AC outlet.

DRAFT

6.3 IR Cable Pin Assignment

Power 3.3V

IR Blaster Signal

IR Signal

Power 3.3V

Grounding

IR Extender

IR Blaster

DRAFT

7. CONNECTION DIAGRAM

IR BLASTER

1.5m

60°

IR RECEIVER

3m 3m

60°

1HDMI OUTHDMI IN 234567LAN

SERVICE

CAT5e/6/7 OUT

STD TV

DC 24V

IR IN IR OUT

EDID

CAT5e/6 In

Link

IR1 Extender

IR2 Blaster

Power

Blu-ray or PS3 Player

3D TV/Display 3D TV/Display

Router (with Internet

Connection)

HDMI

Altri manuali per CHDBT-1H7CE

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CYP Trasmettitore

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente