Eastwood 32559 Manuale utente

14 GAUGE METAL

HAND PUNCH

INSTRUCTIONS

Item #32559

2Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com

The EASTWOOD 14 GAUGE METAL HAND PUNCH is designed to rapidly produce repeatable, clean,

accurate holes in mild steel up to 14 Gauge (5/64”) [2mm] thick making it perfect for creating rivet

holes for custom fabrication work. A compound-leverage design greatly ampliﬁes hand pressure

providing greater accuracy, speed and convenience. The 16 Piece, Eastwood Metal Hand Punch is

supplied with 7 Male and Female Die Sets and Die Installation Tool.

CONTENTS

(1) Metal Hand Punch

with Depth Stop Gauge

(1) Die Installation Key

(1) Complete Set of 7 Male and

Female Punch Dies:

- 3/32” [2.38mm]

- 1/8” [3.18mm]

- 5/32” [3.97mm]

- 3/16” [4.76mm]

- 7/32” [5.56mm]

- 1/4” [6.35mm]

- 9/32” [7.14mm]

SPECIFICATIONS

• Maximum material punching thickness:

- 16 Gauge stainless and high-carbon steels

- 14 Gauge mild steel

- 12 Gauge aluminum

• 1.75” [44mm] Throat Depth allows punching into the center of a 3.5” [88mm] work piece.

• Compound Leverage Action greatly ampliﬁes punching power.

Exceeding rated material limitations can result in severe personal injury

and/or damage to the unit.

The Upper Male Die must be installed first followed by the Lower Female Die.

To order parts and supplies: 800.343.9353 >> eastwood.com 3

READ INSTRUCTIONS

• Thoroughly read and understand this manual before using.

• Save for future reference.

PINCH AND CRUSH HAZARD!

• The Eastwood Metal Hand Punch presents a hand/ﬁnger pinch hazard and

cause potentially serious injuries. Avoid pinching ﬁngers and hands while

handling and operating.

CUT HAZARD!

• Handling sharp metal can cause serious cuts. Wear thick, well-ﬁtting work

gloves to prevent cuts from handling sharp metal.

EYE INJURY HAZARD!

• Metal particles can be ejected from the tool when punching.

Sheet metal edges and corners are sharp and can injure eyes.

Always wear ANSI approved eye protection when operating this tool.

• Strenuous physical force may need to be applied to the Metal Hand Punch

during use. Failure to ensure proper footing can quickly result in a fall which

could inﬂict serious personal injury or property damage. Always work in a

clean, uncluttered environment.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

SAFETY INFORMATION

The following explanations are displayed in this manual, on the labeling, and on all other information

provided with this product:

4Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com

SAFETY INFORMATION

• Excessive resistance while operating could indicate a defect with the

workpiece material or broken or damaged Metal Hand Punch components.

To avoid injury, stop work immediately and inspect workpiece material for

nicks, dents, welds, excessive scale or remaining coatings. Clean or repair

as necessary or discard and begin with a new piece. Also inspect Metal

Hand Punch components for looseness or damage.

DIE INSTALLATION

AND REPLACEMENT

• Using the blade end of the Die Installation Key,

unthread and remove the Anchor Pin (FIG 1)

from the Anchor Arm and Main Body Pivot.

• Rotate the Upper Handle upward and pull the

Anchor Arm backward (FIG 2).

• Slip the Male Punch Die upward through the

lower bore of the Main Body Lower Jaw with

the “T” Head up (FIG 3).

FIG. 1

FIG. 2

FIG. 3

• Move the Upper Handle and Anchor Arm forward

capturing the “T” Head of the Male Die in the

“T” Slot of the Anchor Arm (FIG 4).

• Re-install the Anchor Pin by aligning the pivot

bore of the Anchor Arm and the Main Body and

threading the Anchor Pin back into place (FIG 5).

• Thread the corresponding sized Female Die into

the Lower Jaw with the Slot downward (FIG 6)

and thread into place. If required, use the blade

end of the Die Installation Key to tighten the Die

in place (FIG 7).

• Adjust the Lower, Female Die to allow the Upper

Male Die to fully engage the bore of the Female

Die when the tool Jaws are closed.

• The Metal Hand Punch is now ready for use.

OPERATION

• Before each use, inspect Punching Dies

for cracks and damage.

• Mark desired hole location and place the

workpiece under the center point of the

Upper Male Die.

• If desired, set Work Stop to the required depth.

• Raise Punch Upper Handle to open Punch.

• Insert material and lower Upper Lever to

close Punch.

• Slowly apply increasing pressure to the Punch

by squeezing the Upper Handle and Punch Body

Handles together (FIG 8).

• Once the Die has punched through the metal,

open the Jaws to release the slug.

To order parts and supplies: 800.343.9353 >> eastwood.com 5

FIG. 4

FIG. 5

FIG. 6

FIG. 7

FIG. 8

6Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com

MAINTENANCE

• Before each use, inspect tool and Punching Dies for cracks or damage. If damage is present,

do not use tool.

• After each use, clean tool of any debris and inspect punching dies for damage.

• Apply a thin coat of machine oil on all Punching Die surfaces to prevent corrosion

and maximize performance.

• Lubricate all Metal Punch pivot points with a medium bodied machine oil.

To order parts and supplies: 800.343.9353 >> eastwood.com 7

PROBLEM CAUSE CORRECTION

Upper Die

Stops At

Lower Die

Metal work-

piece too thick

or too hard

Stop all action to avoid serious damage.

Do not exceed material limitations described

in the “SPECIFICATIONS” section.

Metal slug

particles in Die

Stop all action to avoid serious damage.

Remove slug from Dies.

Upper Die

Binding at

Release With

Lower Die

Metal work-

piece too thick

or too hard

Stop all action to avoid serious damage.

Do not exceed material limitations described

in the “SPECIFICATIONS” section.

Metal chips

or particles

in Dies

Stop all action to avoid serious damage.

Remove chips or particles from Dies.

Dies Will Not

Shear Metal

Dies worn

or damaged Follow Die Replacement instructions.

Metal work-

piece too thick

or too hard

Stop all action to avoid serious damage.

Do not exceed material limitations described

in the “SPECIFICATIONS” section.

TROUBLESHOOTING

If you have any questions about the use of this product, please contact

The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: tech@eastwood.com

PDF version of this manual is available at eastwood.com

The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA

800.343.9353 eastwood.com

ADDITIONAL ITEMS

#28038 Sheet Metal Gauge

#13475 Electric Metal Cutting Shears

#32044 Bead Roller Kit

#21489 Shrinker/Stretcher Set

#21491 Shrinker/Stretcher Stand

Indice

Altri manuali Eastwood Utensili

Eastwood

Eastwood 51088 Manuale utente

Eastwood

Eastwood QST 30 Manuale utente

Eastwood

Eastwood 20555 Manuale utente

Eastwood

Eastwood 21566 Manuale utente

Eastwood

Eastwood CONTOUR SCT Manuale utente

Eastwood

Eastwood 21489 Manuale utente

Eastwood

Eastwood 21302 Manuale utente

Eastwood

Eastwood 21487 Manuale utente

Eastwood

Eastwood 20646 Manuale utente

Eastwood

Eastwood 20269 Manuale utente

Eastwood

Eastwood 20642 Manuale utente

Eastwood

Eastwood 21320 Manuale utente

Eastwood

Eastwood 20556 Manuale utente

Eastwood

Eastwood FAIRMOUNT 12PC BEARING SPLITTER/PULLER KIT Manuale utente

Eastwood

Eastwood 20447 Manuale utente

Eastwood

Eastwood Elite 64646 Manuale utente

Eastwood

Eastwood 20254 Manuale utente

Eastwood

Eastwood 25304 Manuale utente

Eastwood

Eastwood VERSA-CUT Manuale utente

Eastwood

Eastwood 32499 Manuale utente

Eastwood

Eastwood Elite 65500 Manuale di installazione

Eastwood

Eastwood 54830 Manuale utente

Eastwood

Eastwood 20629 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare