Extech Instruments 407227 Manuale utente

USER MANUAL

Heavy Duty pH and ORP Meter

Model 407227 Meter and 407728 Kit

2 407227_407228-en-GB_v3.2 10/18

Introduction

Thank you for selecting the Extech Model 407227 pH, mV, and Temperature Meter. This

device measures pH, mV (ORP), and Temperature. The temperature units (C/F) are

selectable and the Calibration and Slope adjustments are conveniently located on the

front panel.

The 407228 is the kit that includes the 407227 meter, pH electrode, temperature probe,

protective holster jacket with stand, and carrying case. An optional ORP electrode

(67500B) is available.

This device is shipped fully tested and calibrated and, with proper use, will provide years

of reliable service. Please visit our website (www.extech.com) to check for the latest

version of this user manual.

3 407227_407228-en-GB_v3.2 10/18

Meter Description

1. BNC connector for pH or optional ORP probe

2. RS-232 PC interface jack

3. LCD display

4. pH electrode

5. Calibration and slope adjustment potentiometers

6. Temperature probe jack

7. LCD contrast adjustment

8. Keypad:

POWER: Press to turn the meter ON or OFF

HOLD: Press to freeze/unfreeze the displayed reading

C/F: Press to select the desired unit of measure for temperature

RECORD: Press to track the MAX, MIN, and AVG readings

RECALL: Press to view the MAX, MIN, and AVG readings

MTC: Manual Temperature Compensation. Refer to the dedicated Manual

Temperature Compensation section for details.

‘>’and ‘>>’used when programming the manual temperature compensation. Refer

to the dedicated Manual Temperature Compensation section.

9. Slide switch to select Manual Temperature Compensation (MTC), Automatic

Temperature Compensation (ATC), and mV (ORP) modes

10. Battery compartment and tilt stand (rear)

11. Protective jacket (remove to access battery compartment)

4 407227_407228-en-GB_v3.2 10/18

Temperature Compensation

For accurate pH measurements and calibration, the temperature of the solution under

test must be known. This can be accomplished manually or automatically. Refer to the

steps for each, below, and determine the best method for the application.

Automatic Temperature Compensation

For Automatic compensation, use the supplied thermometer.

Perform these steps before each use or when the temperature of the solution under

test changes. Note that the thermometer can remain in the solution while taking pH

measurements.

1. Select ‘pH ATC’ on the meter’s front panel slide-switch.

2. Plug the supplied thermometer into the meter’s temperature sensor input jack.

3. Place the other end of the thermometer into the solution under test.

4. Perform a pH calibration or take a pH measurement.

Manual Temperature Compensation

Note: For Manual compensation, an external thermometer is required (not the one

supplied with the meter).

Perform these steps before each use or when the temperature of the solution under

test changes:

1. Place a thermometer in the solution under test and note the reading.

2. Select ‘pH MTC’ on the meter’s front panel slide-switch.

3. Press the "MTC" key and the display will show 25.0oC. Using the ">>" key (for 1 oC

steps) and the ">" key (for 0.1oC steps), edit the displayed temperature. Continue

editing until the displayed temperature equals the measured temperature noted

earlier.

4. Perform pH calibration or take a pH measurement.

Note: If you are replacing the temperature probe with a new probe, please refer to the

temperature calibration section later in this manual.

5 407227_407228-en-GB_v3.2 10/18

pH Operation

Important note: Manual or Automatic Temperature compensation must be engaged

before proceeding with pH calibration and pH measurements.

pH CALIBRATION

Note: It is recommended that the meter be calibrated at least once per day.

1. Connect the pH electrode to the meter’s BNC input jack and rinse it with distilled

water.

2. Press the POWER key to turn the meter ON.

3. Place the electrode in a pH 7 buffer solution.

4. Turn the CAL pH7 potentiometer on the front panel until the display reads 7.00.

5. Rinse the electrode with distilled water.

6. Place the electrode in the pH 4 or pH 10 buffer solution.

7. Turn the SLOPE pH potentiometer until the display reads 4.00 or 10.00.

8. Rinse the electrode in distilled water.

9. Repeat as necessary.

Note that if the adjustments described above do not yield a 4.0, 7.0, or 10.0 pH

reading, the electrode may need replacing.

pH MEASUREMENTS

1. Connect the pH electrode to the meter’s BNC input jack.

2. Connect the temperature probe if using automatic temperature compensation.

Set the manual temperature compensation if not using the temperature probe.

3. Turn the meter ON using the POWER key.

4. Place the electrode and the temperature probe (if using) into the test solution and

read the displayed pH value.

5. After measuring, rinse the electrode and temperature probe (if using) with distilled

water.

6 407227_407228-en-GB_v3.2 10/18

ORP Operation (mV)

1. Connect the optional (67500B) mV ORP electrode to the BNC input jack at the top of

the meter.

2. Turn the meter ON using the POWER button.

3. Select ‘mV’ (millivolts) via the meter’s front panel slide-switch.

4. Rinse the ORP probe in distilled water.

5. Place the electrode in the test solution and read the millivolt (ORP) value.

6. Rinse the electrode with distilled water before storing.

Note that calibration is not required for the ORP function.

Advanced Features

MIN MAX AVG Record / Recall Mode

1. Press the RECORD key (the REC indicator will appear on the LCD).

2. Press the RECALL key to view the highest (MAX) reading recorded since the RECORD

key was first pressed. The MAX indicator will appear on the LCD.

3. Press the RECALL key to view the lowest (MIN) reading recorded since the RECORD

key was first pressed. The MIN indicator will appear on the LCD.

4. Press the RECALL key to view the average (AVG) reading recorded since the RECORD

key was first pressed. The AVG indicator will appear on the LCD.

5. Press the RECORD key again to exit this mode.

6. Note that the Auto Power OFF feature is disabled in this mode.

Automatic Power OFF (APO)

The meter automatically switches OFF after 10 minutes. To defeat APO, put the meter

in the Record mode by pressing the RECORD key. To turn the meter OFF, first exit the

Record mode (long press the RECORD key until the RECORD display icon switches off)

and then press the POWER key.

Data Hold

Press the HOLD key to freeze the displayed reading. The DH indicator will switch on in

the Data Hold mode. Press the HOLD key again to exit the Data Hold mode (the DH

indicator will switch off).

7 407227_407228-en-GB_v3.2 10/18

Battery Replacement

The low battery indicator (LBT) appears when the 9V battery needs replacing.

1. Remove the meter's protective jacket.

2. Open the battery compartment using a coin or screwdriver.

3. Replace the 9V battery and re-assemble.

Never dispose of used batteries or rechargeable batteries in household

waste.

Users are legally required to take used batteries to appropriate collection

sites, the retail store where the batteries were purchased, or wherever

batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The user is

obligated to take end-of-life devices to a designated collection point for the

disposal of electrical and electronic equipment.

Other Battery Safety Reminders

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

PC Interface

For streaming of data to a PC USB port via the RS232 output jack, the optional 407001-

USB kit (RS232 to USB cable) is required. Contact Extech for a copy of the RS232

software ([email protected])

Calibrating a New Temperature Probe (850188)

1. Connect the new temperature probe to the meter’s temperature sensor input jack.

2. Select "pH ATC" via the meter’s front panel slide-switch.

3. Place the temperature probe in a slurry (water with crushed ice) and allow it to

acclimate for approximately 15 minutes.

4. Adjust VR6 (inside the battery compartment, see diagram below) until the displayed

value reads 0°C (32°F).

8 407227_407228-en-GB_v3.2 10/18

Specifications

General Specifications

Display

Dual function LCD with contrast adjust

Input impedance

1012 ohms

Temp. compensation for pH

Automatic and manual 0 ~ 65°C (32 ~ 149°F)

pH electrode compatibility

Any pH electrode with BNC connector

Data hold

Freezes displayed reading

Memory recall

Records / Recalls MAX (maximum), MIN

(minimum), and AVG (average) readings

Auto Power OFF

Meter powers OFF after 10 minutes

PC Interface

Serial RS-232 communication

Over range indication

All dashes on display "- - - -"

Sampling time

Approximately 0.8 seconds

Operating conditions

0°C ~ 50°C (32°F ~ 122°F); < 80% RH

Power supply

9V battery (power consumption 5.7mA approx.)

Weight

270g (0.59 lbs.) including batteries

Dimensions

180 x 72 x 32mm (7.1 x 2.8 x1.3")

Optional accessories

ORP Electrode (67500B)

AC adaptor: 156119 (120V), 156221 (220V)

Range Specifications

Measurement

Range

Resolution

Accuracy (of reading)

0 ~ 14 pH

0.01 pH

± (0.03 pH + 2 digits)

±1999 mV

1 mV

± (0.5% + 1 digits)

Temperature (oC)

0 ~ 50oC

50 ~ 65oC

0.1oC

± 1oC

± 4oC

Temperature (oF)

32 ~ 122oF

122 ~ 149oF

0.1oF

± 1.8oF

± 7.5oF

www.extech.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Strumento di misura

Extech Instruments

Extech Instruments AN100 Manuale utente

Extech Instruments

Extech Instruments HDV-WTX2 Dimensioni

Extech Instruments

Extech Instruments RH401 Manuale utente

Extech Instruments

Extech Instruments MA140 Manuale utente

Extech Instruments

Extech Instruments MO750 Manuale utente

Extech Instruments

Extech Instruments MA150 Manuale utente

Extech Instruments

Extech Instruments UV510-NIST Manuale utente

Extech Instruments

Extech Instruments 382075 Manuale utente

Extech Instruments

Extech Instruments MA410T Manuale utente

Extech Instruments

Extech Instruments 407790A Manuale utente

Extech Instruments

Extech Instruments 461891 Manuale utente

Extech Instruments

Extech Instruments 380560 Manuale utente

Extech Instruments

Extech Instruments SL250W Manuale utente

Extech Instruments

Extech Instruments LT250W Manuale utente

Extech Instruments

Extech Instruments 380940 Manuale utente

Extech Instruments

Extech Instruments LT40 Manuale utente

Extech Instruments

Extech Instruments GRT300 Manuale utente

Extech Instruments

Extech Instruments PM200 Manuale utente

Extech Instruments

Extech Instruments Extech 380976 Manuale utente

Extech Instruments

Extech Instruments CO230 Manuale utente

Extech Instruments

Extech Instruments LT510 Manuale utente

Extech Instruments

Extech Instruments 407123 Manuale utente

Extech Instruments

Extech Instruments 401027 Manuale utente

Extech Instruments

Extech Instruments ExStik FL700 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente