Extech Instruments RH305 Manuale utente

USER GUIDE

Digital Psychrometer

Models RH300 and RH305 (kit)

netzerotools.com

Extech RH305 Hygro Thermometer Psychrometer Kit

Extech RH305-NIST Hygro Thermometer Psychrometer Kit

RH300-EU-EN v1.6 9/13

Introduction

Congratulations on your purchase of the Extech RH300 Digital Psychrometer. This device measures

Humidity, Air Temperature, Dew Point temperature and Wet Bulb temperature. Advanced features

include External Temperature Measurement (with optional probe), Data Hold, selectable Auto Power

Off, and MAX/MIN/Average reading. Careful use of this meter will provide years of reliable service.

Meter Description

1. Humidity Sensor & Air Temperature Sensor

2. Triple LCD Display

3. ON/OFF button

4. T1-T2/Dew Point/T1 button

5. °F/°C select

6. MIN/MAX/RESET button

7. T2-DP/Wet Bulb/T2 button

8. HOLD

button

9. T2 Probe Jack

Note: The battery compartment is located

on the rear of the instrument

netzerotools.com

RH300-EU-EN v1.6 9/13

/WB

T/DP

Display Description

1. Relative Humidity %

2. T1

3. T1-T2

4. Dew

Point

5. Wet

Bulb

6. T2-Dew

Point

7. °C/°F

8. T2

9. Maximum

10. Minimum

11. Low

Battery/Hold

Operation

Open the Protective Sensor Cap

Twist the protective sensor cap, located at the top of the

meter, counter-clockwise a quarter of a turn to expose the

sensor

Plug in the optional external temperature probe (if

needed).

Turn Power ON or OFF

Press the ON/OFF button to turn power on or off. The meter will perform a short self-test when

turned on.

Taking measurements

1. Hold the probe in the area to be tested.

2. Allow adequate time for readings to stabilize.

3. The Relative Humidity measurement appears in

the top display.

4. Pressing the button toggles the lower left

display between T1-T2 (internal temperature-

external temperature), DP (Dew Point), and T1

(internal temperature).

5. Pressing the button toggles the lower right

display between T2-DP (external temperature-

Dew Point), WB (Wet Bulb), and T2 (external

temperature).

Note: If the external probe is not connected, T1-T2, T2-DP, and T2 measurements will not be

displayed.

Selecting temperature units of measure (C/F)

Press and hold the oC/oF button momentarily to toggle the temperature units.

CLOSE OPEN

netzerotools.com

RH300-EU-EN v1.6 9/13

/WB

T/DP

Wet Bulb and Dew Point measurements

1. To read the Wet Bulb measurement, press the button until the symbol Wb appears in the

lower right display. Note: T2 will not be displayed unless the external probe is connected.

2. Wet Bulb temperature is now displayed.

3. To read the Dew Point measurement, press the button until the symbol DP appears in the

lower left display .

4. Dew Point temperature is now displayed.

Minimum (MIN) Maximum (MAX) Function

The MIN/MAX mode allows the user to view only the lowest (MIN) or highest (MAX) readings. Press

the

RESET

MX/MN

button once and MIN appears on the display. The display is now showing the lowest

humidity and temperature reading in memory. Press the

RESET

MX/MN

button again and MAX appears on

the display. The display is now showing the maximum humidity and temperature readings in

memory. To exit the MIN/MAX mode, press the

RESET

MX/MN

button again and the MIN and MAX icons

disappear. To clear the current min/max readings in memory, press and hold the

RESET

MX/MN

button for

more than two seconds.

Data Hold

Press the HOLD button momentarily to freeze the displayed reading. The 'HLD' icon will appear on

the upper right-hand side of the display. Press the HOLD button again to return to normal operation.

Automatic Power OFF

The meter automatically shuts off after a programmed period of time. The default time is 10 minutes.

To program the time period, press down the HOLD button while turning the meter on. Continue to

hold down both buttons and the meter will cycle through the selectable power-off times: n, 2, 5, 10,

20, 40 or 60 minutes. “n” disables the auto power off function. When the desired power-off time

appears in the display, release both buttons to select the time and return to normal operation.

Error Messages

An error message will appear on the display if the meter fails an internal diagnostic test.

1. ER1: Relative Humidity failure. Repair/replacement is necessary.

2. ER2: Internal temperature failure. Repair/replacement necessary.

3. ER3: Reference resistance failure. Repair/replacement necessary.

4. ER4: Internal temperature is out of range.

5. ER5: External temperature is out of range.

netzerotools.com

RH300-EU-EN v1.6 9/13

Calibration

The following verification and calibration procedures require the 33% and 75% RH reference bottles

which are supplied with the Model RH305 kit.

Accuracy Verification

Checking the 33% or 75% RH Calibration:

1. Insert meter’s sensor into the 33% or 75% salt reference bottle.

2. Check the reading after 10 minutes.

3. Verify that the reading is within the accuracy specification.

Relative Humidity Calibration (33% and 75%)

Calibration Preparation

Ensure that fresh batteries are installed in the meter.

Move the protective vent cap to the Open position.

Power the meter ON and set it to display dew point (DP) and wet bulb (Wb) in the lower display

area.

Calibration Procedure

1. Follow the Preparation steps above before continuing.

2. Power the meter OFF.

3. Insert the meter into a 33% salt bottle.

4. Leave the meter OFF for one hour (to stabilize).

5. After the meter has stabilized for one hour:

Press and hold the °C/°F button while powering the unit ON.

The unit enters calibration mode (32.8% flashes on the display).

The DP and Wb display areas show DP ---- Wb ----°C.

6. Once the 33% calibration is complete, the display stops flashing and a constant 32.8% is

displayed.

7. Allow the meter to remain ON and move it to the 75% salt bottle.

8. Allow the meter to remain for one hour in the 75% salt bottle to stabilize.

Important: Do NOT power the meter OFF while in the Calibration mode! Note that

AUTO POWER OFF is disabled while in the Calibration mode.

9. After one hour, press and hold the MN/MX button until 75.3% begins flashing on the meter

display. The meter has now entered the 75.0% calibration stage.

10. After 30 minutes have elapsed, the meter will automatically exit the calibration mode and

return to the normal operating mode.

11. The Calibration is complete, turn power OFF.

Note: To exit from the calibration procedure before completion, press the ON/OFF button.

Note: If the salt at the bottom of the calibration bottles appears dry, the bottles should be replaced.

netzerotools.com

RH300-EU-EN v1.6 9/13

Maintenance

Cleaning and storage

1. The meter should be cleaned with a damp cloth and mild detergent when necessary. Do not use

solvents or abrasives.

2. Store the meter in an area with moderate temperature and humidity (refer to the operating and

storage range in the specifications chart earlier in this manual).

Battery Replacement

When the battery power falls low, the symbol will appear on the LCD. Replace the two (2) 1.5

‘AAA’ batteries by removing the rear battery compartment cover and accessing the battery

compartment. Observe correct polarity when placing the batteries in the compartment. Ensure that

the compartment cover is securely fastened when finished.

EU Directive: Never dispose of used batteries or rechargeable batteries in household

waste. As consumers, users are legally required to take used batteries to appropriate

collection sites, the retail store where the batteries were purchased, or wherever

batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-of-

life devices to a designated collection point for the disposal of electrical and electronic equipment.

Other Battery Safety Reminders

oNever dispose of batteries in a fire. Batteries may explode or leak.

oNever mix battery types. Always install new batteries of the same type.

netzerotools.com

RH300-EU-EN v1.6 9/13

Specifications

Range and Resolution Accuracy

Humidity 0.0 to 100.0% RH ±3% RH (10 to 90%) @ 23oC

Temperature (internal) -20 to 50oC (-4.0 to 122.0oF) ±1oC (±1.8oF)

Temperature (external) -20 to 70oC (-4.0 to 158.0oF) ±1oC (±1.8oF)

Display Triple LCD

Sensor Type Humidity: Precision capacitance sensor

Temperature: Thermistor

Response Time 60 seconds typical

Dew Point -90.4 to 122.0oF (-68 to 50oC) (calculated from RH and Air temperature

measurements)

Wet Bulb -6.88 to 122.0oF (-21.6 to 50oC) (calculated from RH and Air

temperature measurements)

Operating Conditions -20 to 50oC (-4 to 122oF); < 99% RH non-condensing

Storage Conditions -40 to 85oC (-40 to 185oF); <99% RH non-condensing

Power Supply 2 x 1.5V ‘AAA’ batteries

Battery Life Approx. 80 hours

Dimensions / Weight 178.5 x 48.8 x 25.2mm (7 x 1.9 x 1”); 140g (4.9 oz.)

netzerotools.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Strumento di misura

Extech Instruments

Extech Instruments AN310 Manuale utente

Extech Instruments

Extech Instruments PM200 Manuale utente

Extech Instruments

Extech Instruments EX810 Manuale utente

Extech Instruments

Extech Instruments MA150-T Manuale utente

Extech Instruments

Extech Instruments 382090 Manuale utente

Extech Instruments

Extech Instruments ExStik PH100 Manuale utente

Extech Instruments

Extech Instruments HD450 Manuale utente

Extech Instruments

Extech Instruments 403125 Manuale utente

Extech Instruments

Extech Instruments VT30-E Manuale utente

Extech Instruments

Extech Instruments SL10 Manuale utente

Extech Instruments

Extech Instruments 45160 Manuale utente

Extech Instruments

Extech Instruments UV510 Manuale utente

Extech Instruments

Extech Instruments EC170 Manuale utente

Extech Instruments

Extech Instruments 407119-NIST Manuale utente

Extech Instruments

Extech Instruments GX900 Manuale utente

Extech Instruments

Extech Instruments EasyView EA31 Manuale utente

Extech Instruments

Extech Instruments 475040 Manuale utente

Extech Instruments

Extech Instruments RH401 Manuale utente

Extech Instruments

Extech Instruments MO230 Manuale utente

Extech Instruments

Extech Instruments MS400 Manuale utente

Extech Instruments

Extech Instruments MA160 Manuale utente

Extech Instruments

Extech Instruments GRT300 Manuale utente

Extech Instruments

Extech Instruments TB400 Manuale utente

Extech Instruments

Extech Instruments HT200 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente