Extech Instruments VB400 Manuale utente

User's Guide

Pen Vibration Meter

Model VB400

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

VB400-EU-EN-V1.0

Introduction

Congratulations on your purchase of this Extech Meter. The VB400 is designed to provide easy

and accurate velocity and acceleration measurements on industrial machinery. This meter is

shipped fully tested and calibrated and, with proper use, will provide years of reliable service.

Features

•Applications for industrial vibration monitoring :

•All in one pen type digital vibration meter.

•Acceleration, Velocity measurement, RMS measurement value.

•Metric & Imperial display unit

•Frequency range 10 Hz - 1 kHz, sensitivity designed to meet ISO 2954.

•High accuracy and easy to read LCD display.

•Complete with the test pin and magnetic base.

•Low battery indicator.

•IP65 protection.

Safety

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

VB400-EU-EN-V1.0

Meter Description

1. Display

2. Power Button

3. Hold Button

4. Function Button

5. Battery Cover/Compartment

6. Vibration Sensor

7. Sensing Head

8. Magnetic Base

Display Icons

HOLD HOLD has been activated

ACC Acceleration with units : m/s

, ft/s

, g

VEL Velocity with units: mm/s, cm /s, inch/s

Low battery

VB400-EU-EN-V1.0

Operation

Preparation for measurements

1. Press the POWER button to turn the meter on.

2. Check that the display is on and that the low battery icon is not on.

3. If the low battery icon appears, replace the batteries.

4. Attach either the sensing head or the magnetic base by screwing it into the vibration sensor.

Measurements

1. Press the MODE button to step through and set the function (velocity or acceleration) and the

units desired.

2. For non-ferrous surfaces, gently hold the meter (as shown) with the sensing head against the

vibrating surface.

3. For ferrous surfaces, attach the meter to the surface with the magnetic mount.

4. The meter must be held perpendicular to the surface to maintain measurement

accuracy

5. Read the measured value in the display.

Data Hold

1. Press the HOLD button to freeze the display and hold the measured value.

2. Press the HOLD button again to exit and return to normal operation

VB400-EU-EN-V1.0

Zero Adjustment Procedure

Over time the meter ‘0” may drift by a few digits. This is caused by temperature change, battery

voltage and other ageing factors. Usually this small change is not of significance for typical

measurements. To remove the error:

1. Open the battery compartment

2. Hold the battery lid down so contact is made and the meter can be turned on.

3. With no vibration, adjust the meter zero adjustment until the display reads zero (no minus

sign).

Battery lid (1) and Zero adjustment (2)

Battery Replacement

1 Unscrew the meter’s top cover

2 Lift the battery lid and replace the four AAA batteries, observing polarity

3 Replace the cover.

ISO Vibration Severity Guidelines

ISO 10816 Standards provide guidance for evaluating vibration severity in machines operating in

the 10 to 200Hz (600 to 12,000 RPM) frequency range. Examples of these types of machines are

small, direct-coupled, electric motors and pumps, production motors, medium motors, generators,

steam and gas turbines, turbo-compressors, turbo-pumps and fans. The axis of the rotating shaft

may be horizontal, vertical or inclined at any angle.

VB400-EU-EN-V1.0

Specifications

General Specifications

Display LCD, 20 mm x 28 mm.

Measurement Velocity, Acceleration.

(RMSvalue).

Mode Acceleration:

g, m/s2, ft/s2

Velocity: mm/s, cm/s, inch/s

Frequencyrange 10 Hz to 1 KHz

Sampling time Approx. 1 second.

Operating temperature 0 to 50°

( 32 to 122°

Operatinghumidity < 80% RH.

Power supply DC 1.5V battery ( UM-4/AAA ) x 4 PCs.

Power consumption Approx. DC 12 mA.

Weight 240 g ( 0.53 lb ).

Dimension Meter: 175 x 40 x 32 mm, ( 6.9 x 1.6 x 1.3 inch ).

Sensing head: Round 9 mm Dia. x 30 mm.

Accuracy Specifications

Mode Range Resolution Accuracy

0.5 to 199.9m/s20.1

0.05 to 20.39g 0.01

2 to 656ft/s21

±(5%rdg+2digits)

@160Hz, 80Hz, 23±5°C

Acceleration

Calibration point: 50m/s2(160Hz)

0.5 to 199.9 mm/s

0.1mm/s

0.05 to 19.99 cm/s

0.01

0.02 to 7.87inch/s

0.01inch/s

±(5%rdg+2digits)

@160Hz, 80Hz, 23±5°C

Velocity

Calibration point: 50mm/s (160Hz)

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Indice

Altri manuali Extech Instruments Strumento di misura

Extech Instruments

Extech Instruments 42265 Manuale utente

Extech Instruments

Extech Instruments MO220 Manuale utente

Extech Instruments

Extech Instruments RH520 Manuale utente

Extech Instruments

Extech Instruments CO10 Manuale utente

Extech Instruments

Extech Instruments 461830 Manuale utente

Extech Instruments

Extech Instruments 700 Series Manuale utente

Extech Instruments

Extech Instruments CO80 Manuale utente

Extech Instruments

Extech Instruments TKG250 Manuale utente

Extech Instruments

Extech Instruments EC100 Manuale utente

Extech Instruments

Extech Instruments RPM250W Manuale utente

Extech Instruments

Extech Instruments CG304 Manuale utente

Extech Instruments

Extech Instruments DT200 Manuale utente

Extech Instruments

Extech Instruments ExStik II EC400 Manuale utente

Extech Instruments

Extech Instruments PH220-C Manuale utente

Extech Instruments

Extech Instruments HD450 Manuale utente

Extech Instruments

Extech Instruments MO297 Manuale utente

Extech Instruments

Extech Instruments SDL300 Manuale utente

Extech Instruments

Extech Instruments 401036 Manuale utente

Extech Instruments

Extech Instruments TKG100 Manuale utente

Extech Instruments

Extech Instruments PS101 Manuale utente

Extech Instruments

Extech Instruments 380460 Manuale utente

Extech Instruments

Extech Instruments NON-DISPLAY PORTABLE Manuale utente

Extech Instruments

Extech Instruments MO290-NISTL Manuale utente

Extech Instruments

Extech Instruments PQ2071 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente