FAR RAC 181 Manuale utente
RAC 181
- TRANSLATION OF ORIGINAL INSTRUCTIONS
HYDROPNEUMATIC RIVETING TOOL
FOR RIVETS Ø 2,4 ÷ Ø 6
( Ø 6 ALU ONLY )
INSTRUCTIONS FOR USE - SPARE PARTS
GB
RAC 181
RAC 181
www.air-allied.com.au
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
DATE 04-2017 REVISION-01
Far S.r.l. - Giacomo Generali
(Chairman of the Board of Directors)
Quarto Inferiore, 23-03-2016
Via Giovanni XXIII No. 2, herewith
DECLARES
on its sole responsability that the riveting machine
Type: RAC 181 - Hydropneumatic tool Application: for rivets diam.
2,4-6 (6 aluminium only)
whichistheobjectofthisdeclarationcomplieswiththebasic
safety requirements estabilished in the law decree Leg. D.
17/2010 of Machinery Directive 2006/42/CE acknowledge
and subsequent amendments and integrations.
The person who is authorized to create the technical brochure is
(BO), via Giovanni XXIII n. 2.
.............................................
GB
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
SPARE PARTS .......................................17
ACCESSORIES ......................................20
GB
GB
GENERAL NOTES AND USE ..................4
GB
INSTRUCTIONS FOR USE ......................8
GB
RAC 181
RAC 181
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
4
GB
GENERAL NOTES AND USE
The tool must be used for rivets diam. 2,4 - 6 mm.
Diam 6 mm only in aluminium.
The RAC 181 oil pneumatic system assures more power than the pneumatic system used for other models.
reduction in the problems due to the wear and tear of the components, therefore, there will be an increase in
reliability. The technical solutions adopted reduce the dimensions and the weight of the tool which, for these
reasons, make it very handy. The possibilities of leakage from the oil-dynamic system are eliminated by some
sealed gaskets, solve this problem.
RAC 181
RAC 181
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
6
Ø3,1
11,2
Ø2,7
10
1
1
Ø C = 1,43 717006 B = 13
71345507
Ø A = 8,3
710859
Ø C = 1,7 ÷ 2,1 717001 B = 13
71345507
Ø A = 8,3
710859
Ø C = 2,15 ÷ 2,4 717002 B = 13
71345507
Ø A = 8,3
710859
Ø C = 2,6 717003 B = 13
71345507
Ø A = 8,3
710859
Ø C = 2,9 ÷ 3 717004 B = 13
71345507
Ø A = 8,3
710859
Ø C = 3,5 717005 B = 13
71345507
Ø A = 8,3
710859
TAMP Acc. Ø 3,2
Ø C = 2,1
717002 B = 13
71345507
Ø A = 8,3
710859
TAMP Acc. Ø 4
Ø C = 2,6
717003 B = 13
71345507
Ø A = 8,3
710859
B
ØA
Ø1,9
7
Ø3,4
12,5
Ø2,7
10
Ø C
Ø3,1
11,2
Ø2,25
8,5
14
Ø 4
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
DATE 04-2017 REVISION-01
7
RAC 181
RAC 181
TAMP Acc. Ø 4,8
Ø C = 2,9
717004 B = 13
71345507
Ø A = 8,3
710859
MULTIFAR Inox. Ø 3,2
Ø C = 2,15
717002 B = 13
71345507
Ø A = 8,3
710859
MULTIFAR Inox. Ø 4
Ø C = 2,6
717003 B = 13
71345507
Ø A = 8,3
710859
MULTIFAR Inox. Ø 4,8
Ø C = 3,2
717004 B = 13
71345507
Ø A = 8,3
710859
Ø C = 1,80 ÷ 2,15 717001 B = 13
71345507
Ø A = 8,3
710859
Ø C = 2,6 717003 B = 13
71345507
Ø A = 8,3
710859
Ø C = 3,2 717004 B = 13
71345507
Ø A = 8,3
710859
Ø C = 3,4 717005 B = 13
71345507
Ø A = 8,3
710859
B
ØA
1
1
1
Ø3,4
12,5
Ø3,4
12,5
Ø3,1
11,2
Ø2,7
10
1
Ø3,4
12,5
Ø C
Ø2,25
8,5
Ø3,1
11,2
14
Ø 4
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
DATE 04-2017 REVISION-01
GB
8
RAC 181
Company name and
address
Lot number
Designation of the tool
TOOL IDENTIFICATION
The riveting tool RAC 181 is identified from a marking that
showscompanynameandaddressofmanufacturer,designation
of the tool, CE. Always refer to the information on the riveting
tool when requesting technical service.
INSTRUCTIONS FOR USE I
INDEX
GUARANTEE ............................................................................. 14
SAFETY MEASURES AND REQUIREMENTS........................14
TOOL IDENTIFICATION .......................................................14
TECHNICAL DATA ...............................................................15
MAIN COMPONENTS..........................................................15
HOW TO USE YOUR RIVETING TOOL.................................16
MAINTENANCE AND CHANGE OF SIZE...............................18
TOOPING UP THE OIL-DYNAMIC CIRCUIT.........................19
DISPOSAL OF THE RIVETING TOOL ......................................... 19
SAFETY MEASURES AND REQUIREMENTS
CAUTION!!!
All the operations must be done in conformity
with the safety requirements, in order to avoid
any consequence for your and other people’s
security and to allow the best tool work way.
• Read the instructions carefully before using the tool.
•For all maintenance and/or repairs please contact
FAR s.r.l. authorized service centers and use only
original spare parts. FAR s.r.l. may not be held liable
for damages from defective parts caused by failure
to observe what above mentioned (EEC directive
85/374).
The list of the service centres is available on our website
http://www.far.bo.it ( Organization )
• The tool must be used only by expert workers.
• A protective visor and gloves must be put on when using
the tool.
• Use equipment recommended in the maintenance chapter
to do any maintenance and/or regulation of the tool.
• For topping up the oil, we suggest using only fluids in
accordance with the features specified in this working book.
• If any drop of oil touches your skin, you must wash with
water and alkaline soap.
• The tool can be carried and we suggest putting it into its box
after using.
• The tool needs a thorough six-monthly overhaul.
• Repairing and cleaning operations must be done when the
tool is not fed.
• If it is possible, we suggest a safety balancer.
• If the A-weighted emission sound pressure level is more
than 70 dB (A), proper hearing protections have to be worn
(anti-noise headset, etc.).
• The workbench and the work surface must be always clean
and tidy. Messiness could cause injury to persons.
• Do not allow unauthorized persons to use the working tools.
• Make sure that the compressed air feeding hoses are properly
sized for their use.
• Do not carry the connected tool by pulling the hose. The pipe
must be far from any heating sources or from cutting parts.
• Keep the tools in good conditions; do not remove either safety
parts or silencers.
• After repair and/or adjustment operation, make sure to remove
the adjusting spanners.
• Before disconnecting the compressed air hose from the tool
make sure that there is no pressure in the hose.
• These instructions must be carefully followed.
GUARANTEE
FAR riveting tools are covered by a 12-month warranty. The
tool warranty period starts on the date of delivery to the
buyer, as specified in the relevant document. The warranty
covers the user/buyer provided that the tool is purchased
through an authorized dealer and only if it is used for the
purposes for which it was conceived. The warranty shall
not be valid if the tool is not used or maintained as specified
in the instruction and maintenance handbook. In the event
of defects or failures, FAR S.r.l. shall undertake solely to
repair and/or replace the components it judges to be faulty.
RAC 181
RAC 181
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
9
GB
Ø 23
Ø 50
57
295
A
D
MO
BC
I
L
H
F
G
E
270
N
Ø 115
T
RAC 181
TECHNICAL DATA
• Working pressure .................................................. 6,5 BAR
• Min. int. Dia. of the compressed
air feeding hose .................................... min. dia. = 8 mm
• Air consumption per cycle .........................................5,1 Nl
• Maximum force ..........................................6 BAR - 10500 N
• Weight ....................................................................1,60 Kg
• Working temperature.............................................-5°/+50°
• Root mean square in total acceleration frequency (Ac)
to which the arms are subjected.........................< 2,5 m/s2
• A-weighted emission sound pressure level .................81 dBA
• Peak C-weighted instantaneous sound pressure .....< 130 dBC
• A-Weighted sound power...........................................92 dBA
AIR FEED
The air feed must be free from foreign bodies and humidity
in order to protect the tool from premature wear and tear of
the components in movement, therefore we suggest to use a
lubrificator group for compressed air.
MAIN COMPONENTS
A)........................................................................Oil tank plug
B)............................................................Balancer connection
C)....................................................................Nails container
D)..................................................... ON / OFF Button suction
E) .......................................................Rubber protective base
F) ............................................... Compressed air connection
G)................................................................... Suction control
H) ...................................................... Tensile strenght button
I)..........................................................Sleeve carrying nozzle
L) ................................................................................. Nozzle
M).................................................. Suction Device always on
N)...................................................................................... Pin
O)................................................................Insertion pin hole
T) .......................................................................... Nails baffle
RAC 181
RAC 181
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
GB
10
WARNING!
Beforeusingthetoolitis absolutelynecessaryto
fit the nails container (C), or the nails baffle (T).
HOW TO USE YOUR RIVETING TOOL
Controlled suction (factory settings) (pic. f1-f2)
Fromthe"ON"positionensurethatthebutton(D)ispositionedas
in the picture (pic. f1), ie towards the inside of the riveting tool.
The suction starts pressing the lever (G) as shown in the
picture (pic. f2).
Suction OFF (pic. f3-f4-f5)
From the "OFF" position, through the provided pin (N), push in
the button (D), as shown in the picture (pic. f3).
In this setup, the nail comes out from the front by gravity or
from the back of the tool by tilting it, as per picture (pic. f4-f5).
D
D
G
f1
f2
f5
f4
f3
N
RAC 181
RAC 181
Air & Allied Sales (Pacific) Pty Ltd
www.air-allied.com.au
Altri manuali per RAC 181
2
Indice
Altri manuali FAR Utensili
FAR
FAR FHU 05 Manuale utente
FAR
FAR KJ 17-A Manuale utente
FAR
FAR KJ 70 Guida all'installazione
FAR
FAR KJ 73 Manuale utente
FAR
FAR RAC 180 Manuale utente
FAR
FAR RAC 2500 P Guida all'installazione
FAR
FAR RAC 230 Guida
FAR
FAR KJ 21 Guida all'installazione
FAR
FAR KJ 17 Guida all'installazione
FAR
FAR KJ 45/S Guida all'installazione
