FarmTek 12855 Manuale utente
CARTS AND WAGONS
1
Revision date: 06.27.11
STK# Description
108680 Hose Cart
©2011 FarmTek®
All Rights Reserved. Reproduction
is prohibited without permission.
108680
All Terrain Hose Cart
12855
CARTS AND WAGONS
2Revision date: 06.27.11
YOU MUST READ THIS DOCUMENT BEFORE YOU
BEGIN TO ASSEMBLE THE CART.
Thank you for purchasing this hose cart. When properly
assembled and maintained, this product will provide years
of reliable service. These instructions include helpful hints
and important information needed to safely assemble and
properly maintain the cart. Please read these instructions
before you begin.
If you have any questions during the assembly, contact
Customer Service for assistance.
SAFETY PRECAUTIONS
• Do not use the cart if any part is broken or damaged.
• This cart is not a toy. Do not allow children to use the
cart.
• Do not use on inclines; cart may tip or roll away.
• Inflate the tires with ambient air only.
• Inflate the tires to the proper level as indicated on the
tires. Do not inflate tires more than 30 PSI.
• Never use a flammable gas to inflate the tires.
• Never allow riders on the cart.
CARE AND MAINTENANCE
• Periodically check all fasteners to assure they are
tight.
• Clean the cart using water and mild soap. Rinse with
water sprayed from a garden hose.
• Check the tire pressure and adjust to recommended
pressure if needed.
REQUIRED TOOLS
The following list identifies the main tools needed for
assembly. To safely assemble the cart, two (2) individuals
are needed.
• Flathead screwdriver
• Metric and standard wrenches and socket set
• Pliers
UNPACK AND IDENTIFY PARTS
The following steps help to ensure that you have all the
necessary parts before you begin.
1. Unpack the contents of the shipment and place where
you can easily inventory the parts.
2. If anything is missing or you have questions, consult
the Pictorial Parts List or contact Customer Service.
3
Revision date: 06.27.11
CARTS AND WAGONS
Parts List and Tools Required
Wheels (4)
To better align the cart, do not fully tighten
the nuts and bolts until the entire cart is
assembled.
NOTE: Hardware may ship attached to parts.
Photos used in these instructions are not to
scale.
1. Remove lock nut and washer from each
end of the axles (if needed). Slide axles
through the holes of the main frame as
shown in diagram A.
2. Slide one (1) wheel, 12mm flat washer,
and 12mm locknut in that order onto each
end of both axles as shown in diagram B.
Do not over tighten the nuts, wheels spin
freely.
1INSTALL AXLES AND WHEELS
Flat washer and locknut are used
on the outside of the wheel. Install
the wheel with the valve stem to the
outside.
Main Frame (1)
Axles (2)
12mm Flat Washers (4)
12mm Locknuts (4)
Axles
B
Axle
A
Socket/Wrench Set
Pliers
Flat Head Screwdriver
4Revision date: 06.27.11
CARTS AND WAGONS
Parts List and Tools Required
2
NOTE: Hardware may ship attached to parts.
1. Place reel frame inside the main frame with the
hose connection towards the side of the frame with
the two pre-drilled holes.
2. Align the holes of the U-shaped bracket on the reel
frame with the pre-drilled holes in the main frame.
With assistance, secure using 6x30mm bolts,
washers and lock nuts. See diagram A.
3. Insert reel crank through the pre-attached U-bolt on
the main frame and into the crank slot on the reel
frame. Align holes and secure using two (2) 6mm
bolts, one (1) lock nut, and one (1) acorn nut. See
diagram B.
INSTALL REEL FRAME AND REEL CRANK
6x30mm bolt,
washer, and
lock nut
Reel crank
6mm bolts,
lock nut, and
acorn nut
A
B
Reel Frame (1)
Reel Crank (1) 6x30mm Bolts (2)
6mm Washers (2)
Socket/Wrench Set
Pliers
Flat Head Screwdriver
6x25mm Bolts (2)
6mm Lock Nuts (3) Acorn Nut (1)
5
Revision date: 06.27.11
CARTS AND WAGONS
Parts List and Tools Required
1. Slide handle onto the vertical posts of the main
frame.
2. Align the holes of the handle with the holes in the
main frame. Secure using 6x40mm bolts, washers
and lock nuts.
3INSTALL CART HANDLE
6x40mm Bolts (2) 6mm Washers (2)
Socket/Wrench Set
Pliers
Flat Head Screwdriver
6mm Lock Nuts (2)
Cart Handle (1)
6x40mm bolt,
washer, and
lock nut
Cart
Handle
Main
Frame
6Revision date: 06.27.11
CARTS AND WAGONS
Parts List and Tools Required
4INSTALL BASKET AND LEADER HOSE
1. Align the basket holes with the holes on the backside
of the handle. Secure using 8x45mm bolts, washers,
and lock nuts. See diagram A.
2. Insert one (1) rubber washer into the connector end of
the leader hose and connect leader hose to the hose
connection slot on the reel frame. See diagram B.
3. Tighten all connections. Attach garden hose to
threaded water supply tube on the reel frame and
wind hose onto reel. Periodically check connections
to make sure they are tight and secure.
4. Check tire pressure and adjust as needed. Do not
inflate tires more than 30 P.S.I.
Socket/Wrench Set
Pliers
Flat Head Screwdriver
Basket (1)
Leader Hose (1)
8x45mm Bolts (2)
Rubber Washer (1)
A
B
8mm Washers (2) 8mm Lock Nuts (2)
CARTS AND WAGONS
7
Revision date: 06.27.11
Space below is reserved for customer notes.
Questo manuale è adatto per i seguenti modelli
1
Indice
