Flashforge Adventurer 5M Pro Manuale utente

快速启动指南

Quick Start Guide

中文P11

EN/CN - A01 Adventurer 5M Pro / 冒险家5M Pro

1. Please refer to this Guide for initial printer setup.

2. Hot! Avoid touching the heating nozzle in operation.

3. Moving parts in the printer may cause injuries. Do not wear

gloves or other sources of entanglement in operation.

1. 请参照本指南完成打印机的初始准备。

2. 高温危险！打印机喷嘴在工作时会被加热，操作时请避免接触！

3. 可动部件可能会造成卷入挤压和切割伤害。操作机器时请不要

佩戴手套或缠绕物。

Do not power on the printer until installation is completed.

请勿在打印机安装完成之前通电。

安全提示

Safety Notice

For more information, you can visit the Flashforge oﬃcial website.

www.ﬂashforge.com - [Support]

更多产品相关资料您可以登陆闪铸官网查看。

www.sz3dp.com - [技术支持]

1. Open the box. 2. Remove the upper foam packaging,

Quick Start Guide and After-sales Service

Card.

3. Take out the machine, place it on a level

workspace and remove the packaging

bags and tapes.

4. Open the top cover and remove the

upper protective foam.

Unboxing Instructions

5. Remove the filament, power cable, and accessory

box from the chamber protective foam. Remove

the inner protective foam from the extruder.

7. Remove the foam.

6. Move the extruder and chain according to the arrow direction.

Packing List

3D Printer Filament After-sales

Service Card

Spool Holder

(with 2 screws)

0.6mm Nozzle

Quick Start Guide Grease

Power Cable

USB Disk

Glue

Diagonal Pliers

Allen Wrench Set

2.0 2.5 3.0

Screwdriver

Unclogging Pin Tool

Printer Components

11 12 13

1. Top Cover

2. Extruder

3. Switch Button

4. Touch Screen

5. Front Door

6. Auxiliary Cooling Fan

7. Build Plate

8. USB Port

9. Air Filter

10. Screw Holes for Spool Holder

11. Ethernet Input

12. Power Switch

13. Power Socket

1. Take out the two screws and spool holder from

the accessory box.

2. Install the spool holder at the position shown

in the figure with the two screws.

Please tighten them using a

2.0mm Allen wrench.

Install the Spool Holder

Note

Please ensure the platform has been cleared up.

Please use a 2.0mm Allen wrench to remove four screws which lock the build plate (as indicated

by the arrow).

Unlock the Build Plate

Note

1. Connect the power, turn on the power switch, and press

the switch button to turn on the screen.

* The interface layout may change whenever there is an upgrade of firmware.

Power switch

2. Following the guide on the screen, select

the language.

3. Click [Next] according to screen prompts and the machine will perform the first calibration.

Vibrations and noise during calibration are normal. (Note: Please keep the machine on a

stable surface and do not move it during calibration.)

First Print

Switch button

4. Load filament following the on-screen startup boot:

a. Cut off the bent part of the filament end.

C1. Click [Load] and select [PLA] for the first print. C2. Wait for the extruder to heat up.

b. Hang the filament on the spool holder. Pass it through the filament sensor until it’s seen

from the other end of the filament guide tube. Push it forward to the feed roller, until it

can not go further. (Please use PLA filament for the first print on initial setup).

Altri manuali per Adventurer 5M Pro

Indice

Altri manuali Flashforge Stampante 3D

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge Guinder II Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Cura Manuale

Flashforge

Flashforge Creator Pro Manuale utente

Flashforge

Flashforge Adventurer 3 Pro 2 Manuale utente

Flashforge

Flashforge Creator Pro 2 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Inventor Manuale utente

Flashforge

Flashforge Inventor 2 Manuale utente

Flashforge

Flashforge Finder 3 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Creator 3 Pro Manuale utente

Flashforge

Flashforge Inventor Manuale utente

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge Adventurer 5M Pro Manuale utente

Flashforge

Flashforge Finder Istruzioni di installazione e manutenzione

Flashforge

Flashforge Cura Manuale

Flashforge

Flashforge Adventurer 4 Manuale utente

Flashforge

Flashforge Creator Manuale di istruzioni

Flashforge

Flashforge Creator 4 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente