Flashforge DREAMER Manuale utente

SZ01-ZN/EN-A07

P18

DREAMER

01

1. Open the carton and take out lid of top of the

printer. On the lid, there is one quick start, one

after-sales service, one SD card, one leveling

card and two build tapes.

3. Lift the printer out of the carton.

5. Tear off tapes at the printer bottom, remove

bubble bag outside the printer.

6. Take out the foam on the top of the printer.

4. You will find a tool bag and one USB cable.

2. Take the power cable out. Remove two top foam

sheets.

02

10. Remove the foam from the back of the logo

board.

11. Hold both sides of the printer, lift up the printer

slowly, thus removing filament under build

plate easily. Do not make build plate collide

with extruder.

8. Remove bubble bag outside the extruder, put

extruder on the extruder mounting base.

Notice: The extruder should be put as is shown

(extruder fan should towards the front of the

printer)

7. Open the paper box on the top of the printer,

there is an extruder, two side panels and an

extruder's accessory kit inside. Take the

extruder and the paper box out, notice that

the cable bunch connected with extruder is

short, do not hang the extruder in the air.

9. Shear three ties off on both sides of X-axis guide rod.

03

12. Take out the paper board. 13. Take out filament first and then remove foam.

15. Finally press build plate slowly to printer

bottom.

14. Notice: Do not miss either filament spool

holder on two pieces of foam.

16. Dreamer unboxing completed.

Suggest keeping packing materials well for

follow-up storage and shipping.

04

Tool Bag Contents:

Graver / Tweezer / Scraper / Accesories box

( contents: Thumb screw / PTFE tubes*2 /

M3x16 Bolt / Nut ) / Tool bag ( contents: Allen

wrenches*2 / Phillips screwdriver /

Unclogging pin tool / Wrench / Grease)

Extruder’s Accessory Kit Contents:

M3x8 Bolts*2 / M3x6 Bolts / Turbofan baffle

Tool Bag

6.Platform Support

19.USB Cable Input

8.Thumb Screw

05

06

bag

07

08

09

For putting filament through guide tube easily, please install filament in a proper way.

1. Take out the filament, remove vacuum packing and put it beside the left fixed seat of the build plate.

Install Filament

2. For putting PLA filament through guide tube

easily, please install filament in a proper way.

3. Put filament through guide tube.

Filament

Guide tube

Filament

Guide tube

Filament

Guide tube

Correct Wrong

Correct

Filament

Guide tube

Left side

Wrong

Filament

Guide tube

Right side

Altri manuali per DREAMER

6

Indice

Altri manuali Flashforge Stampante 3D

Flashforge

Flashforge Guider II Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Guider Manuale utente

Flashforge

Flashforge AD1 Manuale utente

Flashforge

Flashforge Creator 4 Manuale utente

Flashforge

Flashforge Creator 3 Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge Waxjet 400 Manuale utente

Flashforge

Flashforge Creator Pro Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Adventurer 5M Pro Manuale utente

Flashforge

Flashforge CN/EN-A01 Manuale utente

Flashforge

Flashforge Guider 2 Manuale utente

Flashforge

Flashforge Cura Manuale

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge Creator Manuale di istruzioni

Flashforge

Flashforge Guider 3 Manuale utente

Flashforge

Flashforge Inventor 2 Manuale utente

Flashforge

Flashforge Adventurer 4 Manuale utente

Flashforge

Flashforge Creator 3 Pro Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente