Front Runner SLIMLINE II Manuale utente
ENG
KRFE004T_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
1
Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
KRFE004T
READ ME FIRST
START HERE!
front runner FORD EXPLORER (2020-CURRENT)
SLIMLINE II ROOF RAIL RACK KIT
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
KRFE004T_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
2
FIGURE 1.1
IN THE BOX
1 1 X Slimline II Tray - 1345mm(W) X 1358mm(L)
2 1 X Spacer Set
3 3 X Grab On Foot Set
4 3 X Outer Grip Set
5 3 X Inner Grip Set
3mm
5mm 13mm
1GET ORGANIZED
1
2
3
4
5
TOOLS NEEDED
© 2020 FRONT RUNNER VEHICLE OUTFITTERS
3
KRFE004T_REV_A00
FIT AND SECURE
2
2.1
2.2
2.3
Assemble your Slimline II Tray, referring to
the RRSTUNI fitment guide.
Flip the Tray so that the bottom of the Tray
faces up.
Insert eight M8x16 Hex Bolts into the Slats
machined slots as shown.
Insert four M8x30 Hex Bolts into the Slats
machined slots as shown.
Refer to RRSTUNI and fit your Wind Deflector.
Loosely assemble the three Grab On Foot
Sets (Item 3) onto the slats indicated in 2.2
as shown using M8 Flat Washers and M8
Nyloc Nuts.
Note the Spacers must be used on the rear
feet only.
A
A
A
B
B
2
3
3
© 2020 FRONT RUNNER VEHICLE OUTFITTERS
4
KRFE004T_REV_A00
FIT AND SECURE
2
2.4
2.5
Refer to GOFR001 fitment guide.
Remove the Front Covers from all the Base
Feet by loosening the two M5x10 Button
Head Screws.
Loosen and remove the M5x60 Cap Screw,
M5 Spring Washer and Cap Screw Washer.
Loosley fit one Inner Grip and one Outer Grip
to each Grab On Foot using a M5 Cap Screw,
M5 Spring Washer and M5 Cap Screw
Washer removed.
Inner Grip
Outer Grip
FIT AND SECURE
3
3.1
4MM
Make sure that the wind deflector is
installed before you proceed to the next
step.
© 2020 FRONT RUNNER VEHICLE OUTFITTERS
5
KRFE004T_REV_A00
4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or online.
IMPORTANT!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER
FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
FIT AND SECURE
3
2.2
3.2
3.3
Center the rack and tighten fully. Finish off by placing M8 Nut Caps over the M8 Nyloc Nuts.
Place your Tray on the vehicle
positioning all the feet so that they rest
on top of the roof rails.
Position the LH and RH front Grab On
Feet as shown.
Fully tighten all the M6x50 Cap Screws
to secure the Tray onto the rails.
Refit the Front Cover Plates.
13mm
Tightening Torque 6Nm
Make sure there are no movement on
the rack after fully tightening all the
fasteners.
Altri manuali per SLIMLINE II
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Front Runner Accessori per automobili
Front Runner
Front Runner KRLDT03L Manuale di istruzioni
Front Runner
Front Runner FSLI021 Manuale utente
Front Runner
Front Runner SSDR012 Manuale utente
Front Runner
Front Runner JADA010 Manuale utente
Front Runner
Front Runner FAJK007 Manuale utente
Front Runner
Front Runner TRAC003 Manuale utente
Front Runner
Front Runner TRCA004 Manuale utente
Front Runner
Front Runner KRJW021T Manuale utente
Front Runner
Front Runner TRCA010 Manuale utente
Front Runner
Front Runner FATT002 Manuale utente
Front Runner
Front Runner RRAC178 Manuale utente
Front Runner
Front Runner FAJL002 Manuale utente
Front Runner
Front Runner PRO UNDER RACK TABLE bracket Manuale utente
Front Runner
Front Runner VACC120 Manuale utente
Front Runner
Front Runner SSBS008 Manuale utente
Front Runner
Front Runner KRTT001T Manuale utente
Front Runner
Front Runner SHOW013 Manuale utente
Front Runner
Front Runner SSDS111 Manuale utente
Front Runner
Front Runner SAFE010 Manuale utente
Front Runner
Front Runner SSDR010 Manuale utente
