Fujitsu PRIMERGY BX600 Guida











BX600

1Checking the items

supplied

Check the contents in the package using

the "Contents List".

If any items are missing, inform an ofce listed in

the "Contact Information".

B7FH-4871-01EN-00

2Reading and understand-

ing "Safety Precautions"

Before using this server, be sure to read and un-

derstand the attached "Safety Precautions".

Also check it when connecting, installing internal options

and setting up this server.

3Checking location before installing the server

For details on installing the rack, refer to the "Installation Guide for the RACK" and manuals provided with the rack.

nConditions

When installing this server avoid the following areas.

- Humid, dusty, or oily areas

- Poorly ventilated areas

- Areas close to re or other sources of heat

- Areas close to water

- Areas close to direct sunlight or near heating appliances

- Areas with a temperature of below 10°C or above 35°C

- Areas with humidity of less than 20% or more than 80%

- Salty areas

- Areas where corrosive gas is generated

- Areas where cables become trip hazards

- Areas where strong magnetic elds are generated, such as near TVs and speakers

- Areas where the device is not stable and could tip over and hurt somebody

- In dusty areas, dust will quickly stick to the front and backside of the server. Since this can cause failure, changing the

installation place is recommended.

- Be sure to secure the rack with stabilizers to prevent the device from tipping over.

nPRIMERGY BX600 Manuals

Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD.

[CD-ROM Drive] :\MANUAL\INDEX.PDF

Manuals can be displayed using Acrobat® Reader® or Adobe® Reader®. If using Acrobat® Reader®, use version 5.0 or later.

*This manual corresponds with BX600 S3 Blade Server System Unit and BX620 S4 Server Blade. For chassis and server blades not described in

this guide, refer to the corresponding manual on the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).

nInstalling the server to the rack

When installing or removing the server, please contact an

ofce listed in the "Contact Information".

1Open the front and rear doors of the

rack.

2Align rail with the length of the rack,

and temporarily fasten the rack using

screws.









3Attach the rail to the rack.

Tighten the temporarily fastened screws from step



















4Install the chassis to the rack.

Place the chassis on the rail, slide it to the very

back and install to the rack.

5Secure the chassis and rack.



When installing for the rst time, be sure to slide the

chassis to the very back and secure it completely to the

rack.

6Install a server blade or a dummy

server blade to the chassis.

Do not leave any server blade slot empty.





- When sliding or returning the chassis or server blade to

their original position, be careful not to pinch your ngers

and clothes. This may cause injury.

- The rack rail does not have a locking mechanism, be

careful not to drop the chassis when sliding it out.

- Do not install the BX620 S4 server blade in the BX600

S2 chassis’ server blade slots 4, or 10.

Abnormal operation will occur.

- Attach the blank panels that come with the rack to

locations where no server or peripheral devices are

installed.

nAvailable internal options and installation locations



















- After installing internal options, check that the order and place of installation are correct and that the connectors and cables

are correctly attached.

- For details about server blade internal options, refer to the "User's Guide".

4Installing internal options

If internal options have been purchased separately, install them before installing the operating system.

In the following case, do not install internal options now.

- Custom Made Service

When installing internal options, perform operations after

reading the following manuals.



"BX600 S3 Blade Server System Unit

Hardware Guide Chapter 4 Installing

Options"



"Chapter 7 Installing Internal Options"



"PRIMERGY Server Books" / "Supplement"

- Install the non-system hard disk unit after the OS has

been installed. Installing the OS after the hard disk unit

has been installed may end in an error.

- When installing a server blade with an installed Fibre

Channel Expansion Board in the chassis, install an

SFP module in the Fibre Channel connector of the cor-

responding FC Pass-Thru Blade or in the Fibre Channel

Pass Thru Blade SFP module slot.

5Connecting peripheral devices

Peripheral devices, such as the keyboard and mouse, etc., are connected to the server in the following

order.



































- Use a power cable that meets your country's standard.

- Connect cables with enough allowance for operation while the device is pulled out from the rack.

nAfter connecting the power cable

After connecting the power cable, secure the power cable to one of the handles on the rear of the chassis with the

release tie. This prevents the power cable from being disconnected if the chassis is moved forward.











- When disconnecting the chassis power cable make sure

to disconnect the power connector on the chassis.

- When securing the power cable with the release tie,

make sure to secure it in a location that will not interfere

with removal of the power unit.

- When expanding the power unit, make sure to use the

release tie included with the chassis to secure the power

cable.

nPowering on the main power supply of the chassis

1Open the rack door.

2Power on the peripheral devices, such

as the display.

3Push the main power switch on front of

the chassis.

Continue to push it until the LED turns green.







6Turning on the power and setting hardware

Set each blade to enable normal operation of this server.

- Be sure to set a password for the Management Blade and Switch Blade and check/set the time of the Management Blade.

- Record the settings performed by the Management Blade and Switch Blade, using display hardcopy and notes, etc.

- For details about setting options not described in this manual, refer to the manual provided with each option.

nSetting Management Blade

Before powering on the main power supply of the chassis, perform Management Blade default settings such as

password. For details, refer to "BX600 Management Blade Hardware Guide".



"BX600 Management Blade Hardware Guide 2.3 Default Settings"

- Wait 2 or more minutes after connecting the power cable

before powering on the chassis.

- Do not power on the server blade at this time.

1When connecting CD-ROM drives,

plug the power cable of the CD-ROM

drive into the outlet.

2Connect USB Cable to the connector

of the server blade.



3Connect the oppy disk drive or CD-

ROM drive to the USB Cable.

nConnecting oppy disk drives/CD-ROM (or DVD-ROM) drives

For this server, oppy disk drives including USB interface and CD-ROM drives (or DVD-ROM drives) can be con-

nected to the server blade using USB Cables.

lBIOS Setup Utility

Change the settings in the following cases:

- When changing a drive which boots up this server

- When performing remote installation

- When optional devices are installed

You can write down hardware conguration and setting

values of the BIOS Setup Utility in the "Conguration

Sheets" that is available from Fujitsu PRIMERGY website

(http://primergy.fujitsu.com).

1Prepare the ServerStart CD-ROM.

2Turn on the server blade, and insert the

ServerStart Disc1 CD-ROM immedi-

ately.

1. Press the power switch of the server blade.







2. Press the CD-ROM eject button (OPEN), and

insert the ServerStart Disc1 CD-ROM.

3Set the hardware.

If no hardware settings are performed, skip to the

next step when a message to insert the ServerStart

oppy disk is displayed.

lBIOS Setup Utility

1. If the "Press F2 to run Setup" message

appears during server startup (during POST),

press [F2] while the message is being

displayed.

2. Check/change the BIOS settings.

3. Select "Save Changes & Exit" from the Exit

menu and press [Enter].

4. Move the cursor to "Yes" using [←] [→] and

press [Enter].

For the use of Linux distribution with this server,

refer to the Fujitsu PRIMERGY website (http://

primergy.fujitsu.com).

nSetting Switch Blade

Perform default settings such as password for each installed Switch Blade. For details, refer to "PRIMERGY

BX600 LAN Switch Blade Document CD".

Do not set VLAN at this time.

nSetting Server Blade

Power on the server blade, and perform settings for the BIOS Setup Utility as required. Set for each installed

blade.



"Chapter 8 Hardware Conguration/Utilities"

Before powering on, be sure to check that the CD-ROM drive and oppy disk drive are connected to the server blade where

software will be installed, and that a display is connected to the chassis.

7Installing the OS

This section explains the procedures to install the OS using ServerStart.

For details about OS installation procedures without using ServerStart, refer to the "User's Guide".



"Chapter 4 Manual OS Installation"

1Insert the ServerStart oppy disk

supplied with this server, and click

[Next].

The ServerStart initialization process starts.

When the process is completed, the LICENSE

AGREEMENT window appears.

2Click [Accept].

The [Welcome to ServerStart] window appears.

3Click [Guided / Expert Installation].

"Please Select your keyboard" window appears.

4Select your keyboard language from

the drop-down list and click [OK].

The subsequent start procedure may take several

minutes. The [Welcome to ServerStart] window ap-

pears.

5Click [Click here to prepare and/or initi-

ate an operating system installation].

The [Select the operating system to be installed]

window appears.

Click [Special Hints on Operating System Installa-

tion] and read the contents.

6Click [MS Windows Operating Sys-

tems].

7Click the OS to be installed.

8Click[Prepare & initiate an unattended

installation of (OS)].

The guided mode for the selected OS starts up.

9Click [Start here to create a complete

conguration le].

The [Open ServerStart Conguration File] window

appears.

Select the conguration le and click

[Create].

The wizard starts up automatically.

Set the server information.

Click the wizard sequentially,

and enter the server information.

Clicking [help] under the wizard window displays

explanations of items and setting hints.

1. RAID and Disk wizard

Congure RAID, and create and format

hard disk partitions.

2. (OS) Install wizard

Set the computer information, user infor-

mation, network protocol, etc.

3. Application wizard

It is recommended to install the application

selected as default.

Click [Close and save Conguration

File].

Click [Save As] and save the conguration le.

Click [Click here, to Start the Installa-

tion of (OS)].

The license window appears.

Follow the window instructions.

Incorrect settings will cause errors to be

displayed. Enter correct values manually to

continue the process.

When a message indicating installation

completion appears, press any key.

Restart the system.

Click [Start] g [Shutdown]. Select [Restart] and

click [OK].

Set an administrator account for the

RAID management tool (ServerView

RAID).

8Turning off the power and installing optional devices

Install optional devices to be installed after OS installation, such as a UPS device.



"Chapter 7 Installing Internal Options"

9Hints for error handling

In preparation of a failure occurring, set the following:



"Chapter 5 Operations after OS Installation"

- Set to collect memory dump

By setting to collect memory dump, debugging information can be saved when a STOP error (blue screen) or a hangup occurs

in the system. Saving the debugging information helps to analyze the cause of the error.

- Create a system restoration disk.

When the system le or system environments are damaged, the system can be recongured with the content saved in the system

restoration disk.

- Store system settings

By storing the BIOS settings, the original information can be recovered when the setting information is lost.

When this server is installed, record and save the BIOS settings by yourself.

Be careful not to lose the stored BIOS setting information, as you must provide this in maintenance.

When the settings are completed, make sure to check notes before operation.



"5.5 Notes Before Operating the Server"

For details about maintenance after operations have started, refer to "User's Guide Chapter 9 Operation and Maintenance".

1Check that no medium is inserted in the

oppy disk drive or CD-ROM drive.

2Exit the operating system (OS).

After the OS is exited, the server is automatically

turned off. When the power of the server blade

is not off after the OS is exited, press the power

switch on the front of the server blade.

3Press the main power switch on front

of the chassis.

Continue pressing the switch until main LED of

the chassis turns off.

4Power off the peripheral devices, such

as the display.

5Install the optional devices.

- After optional devices are installed, set the VLAN of

the network blade, BIOS Setup Utility as required.

For details about setting procedures, refer to

"PRIMERGY BX600 LAN Switch Blade Document CD",

"User's Guide Chapter 8 Hardware Conguration/

Utilities", or the option’s manual.

- After UPS is installed, set the BIOS Setup Utility as

required. For details about setting procedures, refer to

"User’s Guide 5.5.4 Notes on Advanced Uninterruptible

Power Supply (UPS)".

- When turning on the server again after turning it off,

wait for at least ten seconds and then press the

power switch. If the server is turned on straight after

being turned off, an error will occur that may cause

damage.

- If removing the server blade from the chassis, or

removing the power cable of the chassis after turning

off the server blade, wait for about 20 seconds

before performing the operation.

10 Support and service

lPRIMERGY information

The latest PRIMERGY, Update module, driver, and soft-

ware information is available at the address below. Use as

necessary.

http://primergy.fujitsu.com

lBefore requesting repairs

If an error occurs in this server, refer to "User's Guide 9.2

Troubleshooting". If problems can still not be solved, con-

tact an ofce listed in the "Contact Information".

When contacting an ofce listed in the "Contact Informa-

tion", inform them of the product ID and manufactures

number that are detailed on labels on the base of the server.





















Also read the points to note about requesting repairs in

"User's Guide 9.8.2 Contacting Maintenance Support" in

advance.

Print the "Conguration Sheets"- "Accident sheet" that

is available from Fujitsu PRIMERGY website (http://

primergy.fujitsu.com) and enter the conrmed information.

lNon-durable components

Depending on the environment and period of usage there

will be non-durable components that require replacement

within the warranty period. For details refer to "Blade

Server System Unit Hardware Guide 6.4 Non-durable Com-

ponents" and "User’s Guide 9.8.1 Maintenance Service" - "

■Non-durable Components".

11 Recycling

When disposing of this server, contact an ofce listed in the "Contact Information". This server must be disposed of as

industrial waste.

Contact Information

lAustralia:

Fujitsu Australia Limited

Tel: +61-2-9776-4555

Fax: +61-2-9776-4556

Address: 2 Julius Avenue (Cnr Delhi Road)

North Ryde, Australia N.S.W. 2113

lChina:

Fujitsu (China) Holdings Co., Ltd.

Tel: +86-21-5292-9889

Fax: +86-21-5292-9566

Address: 18F, Citic Square, 1168 West Nanjing Road Shanghai, China 200041

lHong Kong:

Fujitsu Hong Kong Limited

Tel: +852-2827-5780

Fax: +852-2827-4724

Address: 10/F., Lincoln House, 979 King's Road

Taikoo Place, Island East, Hong Kong

lIndonesia:

PT. Fujitsu Systems Indonesia Ofces Headquarters

Tel: +62-21-570-9330 (Hunting)

Fax: +62-21-573-5150

Address: Wisma Kyoei Prince 10th Floor Jl. Jend. Sudirman Kav 3-4

Jakarta, Indonesia 10220

lKorea:

Fujitsu Korea Ltd.

Tel: +82-2-3787-6000

Fax: +82-2-3787-6066

Address: Susong Tower Building, 83-1 Susong-Dong

Jongno-Gu, Seoul, Republic of Korea 110-140

lMalaysia:

Fujitsu (Malaysia) Sdn. Bhd.

Tel: +60-3-8318-3700

Fax: +60-3-8318-8700

Address: 1st Floor, No.3505 Jalan Technokrat 5

63000 Cyberjaya, Selangor Darul Ehsan Malaysia

lPhilippines:

Fujitsu Philippines, Inc.

Tel: +63-2-812-4001

Fax: +63-2-817-7576

Address: 2nd Floor, United Life Building, A. Arnaiz

Legaspi Village, Makati, Metro Manila Philippines

lSingapore:

Fujitsu Asia Pte. Ltd.

Tel: +65-6777-6577

Fax: +65-6771-5502

Address: 20, Science Park Road, #03-01 TeleTech Park,

Singapore Science Park II, Singapore 117674

lTaiwan:

Fujitsu Taiwan Limited

Tel: +886-2-2311-2255

Fax: +886-2-2311-2277

Address: 19F, No.39, Section 1, Chung hwa Road Taipei, Taiwan

lThailand:

Fujitsu Systems Business (Thailand) Ltd.

Tel: +66-2-500-1500

Fax: +66-2-500-1555

Address: 12th Floor, Olympia Thai Tower, 444 Rachadapisek Road

Samsennok, Huaykwang, Bangkok, Thailand 10310

lVietnam:

Fujitsu Vietnam Limited

Tel: +84-4-831-3895

Fax: +84-4-831-3898

Address: Unit 802-8th oor, Fortuna Tower Hanoi 6B Lang ha Street,

Ba dinh District, Hanoi Socialist Republic of Vietnam

lUnited States:

Fujitsu Computer Systems Corporation

Tel: +1-800-831-3183

Fax: +1-408-496-0575

Address: 1250 East Arques Avenue, Sunnyvale, CA USA 94088-3470

For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com).

Altri manuali per PRIMERGY BX600

Indice

Altri manuali Fujitsu Server

Fujitsu

Fujitsu PRIMERGY T850 Guida utente

Fujitsu

Fujitsu PRIMERGY RX100 S8 Manuale utente

Fujitsu

Fujitsu l ETERNUS AF Manuale utente

Fujitsu

Fujitsu SPARC Enterprise T5140 Guida all'installazione

Fujitsu

Fujitsu SPARC Enterprise M8000 Manuale di servizio

Fujitsu

Fujitsu SE700 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX924 S2 Manuale utente

Fujitsu

Fujitsu PRIMERGY MX130 S1 Manuale utente

Fujitsu

Fujitsu PRIMERGY GX2570 M6 Manuale utente

Fujitsu

Fujitsu FUTRO S700 Manuale utente

Fujitsu

Fujitsu PRIMEQUEST 2400E3 Istruzioni operative e di manutenzione

Fujitsu

Fujitsu PRIMERGY CX25 0 M4 Series Istruzioni per l'installazione

Fujitsu

Fujitsu PRIMERGY BX300 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX1330 M3 Manuale utente

Fujitsu

Fujitsu PRIMERGY CX122 S1 Manuale del proprietario

Fujitsu

Fujitsu SPARC Enterprise M4000 Manuale utente

Fujitsu

Fujitsu SPARC Enterprise M4000 Manuale

Fujitsu

Fujitsu PRIMERGY TX300 S3 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX300 S5 Manuale utente

Fujitsu

Fujitsu PRIMERGY RX2540 M4 Manuale utente

Fujitsu

Fujitsu PRIMERGY TX120 S2 Manuale utente

Fujitsu

Fujitsu SPARC Enterprise M4000 Manuale utente

Fujitsu

Fujitsu PRIMERGY BX920 S1 Manuale utente

Fujitsu

Fujitsu PRIMEQUEST 1000 Series Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente