Hioki 3660 Manuale utente

INSTRUCTION MANUAL

LAN CABLE HiTESTER

3660

Contents

Introduction 1

Inspection 1

Safety Notes 2

Notes on Use 5

Chapter 1 Overview 7

1.1 Product Overview 7

1.2 Features 8

1.3 Identification of Controls and

Indicators 9

Chapter 2 Checking Method 13

2.1 Preparation for Checks 14

2.2 Checking Method 15

Chapter 3 Supplement 25

3.1 Wiremap Pair Display 25

3.2 Cable Length Measurement 26

Chapter 4 Cautions Concerning Checks 27

Chapter 5 Terminator 29

Chapter 6 Specifications 33

Chapter 7 Maintenance and Service 37

7.1 Changing the battery 37

7.2 Cleaning 39

7.3 Service 39

__________________________________________________

_____________________________________________

Introduction

Inspection

Thank you for purchasing the HIOKI 3660 LAN

CABLE HiTESTER. To obtain maximum

performance from the product, please read this

manual first, and keep it handy for future

reference.

When you receive the product, inspect it

carefully to ensure that no damage occurred

during shipping. In particular, check the

accessories, panel switches. If damage is

evident, or if it fails to operate according to the

specifications, contact your dealer or Hioki

representative.

Accessories

9336 WIREMAP TERMINATOR 1

3853 CARRYING CASE 1

LR6 alkaline battery 6

Instruction manual (Japanese&English) 1 each

__________________________________________________

_____________________________________________

WARNING

This product is designed to conform to IEC

61010 Safety Standards, and has been

thoroughly tested for safety prior to shipment.

However, mishandling during use could result

in injury or death, as well as damage to the

product. Be certain that you understand the

instructions and precautions in the manual

before use. We disclaim any responsibility for

accidents or injuries not resulting directly from

product defects.

The symbol printed on the product indicates

that the user should refer to a corresponding topic

in the manual (marked with the symbol) before

using the relevant function.

In the manual, the symbol indicates particularly

important information that the user should read

before using the product.

Indicates the ON side of the power switch.

Indicates the OFF side of the power switch.

Safety Notes

This manual contains information and warnings

essential for safe operation of the product and

for maintaining it in safe operating condition.

Before using the product, be sure to carefully

read the following safety notes.

Safety symbols

__________________________________________________

_____________________________________________

DANGER

Indicates that incorrect operation presents an

extreme hazard that could result in serious

injury or death to the user.

WARNING

Indicates that incorrect operation presents a

significant hazard that could result in serious

injury or death to the user.

CAUTION Indicates that incorrect operation presents a

possibility of injury to the user or damage to

the product.

NOTE Advisory items related to performance or

correct operation of the product.

rdg. (reading or displayed value)

The value currently being measured and indicated

on the measuring product.

dgt. (resolution)

The smallest displayable unit on a digital

measuring product, i.e., the input value that causes

the digital display to show a "1".

The following symbols in this manual indicate

the relative importance of cautions and

warnings.

Accuracy

We define measurement tolerances in terms of

rdg. (reading) values, with the following

meanings:

__________________________________________________

_____________________________________________

CAT I Secondary electrical circuits connected to an AC electrical

outlet through a transformer or similar device.

CAT II Primary electrical circuits in equipment connected to an AC

electrical outlet by a power cord (portable tools, household

appliances, etc.)

CAT III Primary electrical circuits of heavy equipment (fixed

installations) connected directly to the distribution panel, and

feeders from the distribution panel to outlets.

CAT IV The circuit from the service drop to the service entrance,

and to the power meter and primary overcurrent protection

device (distribution panel).

Measurement categories (Overvoltage categories)

This product complies with CAT I safety requirements.

To ensure safe operation of measurement products, IEC

61010 establishes safety standards for various electrical

environments, categorized as CAT I to CAT IV, and

called measurement categories. These are defined as

follows.

Higher-numbered categories correspond to electrical

environments with greater momentary energy. So a

measurement device designed for CAT III environments

can endure greater momentary energy than a device

designed for CAT II. Using a measurement product in an

environment designated with a higher-numbered category

than that for which the product is rated could result in a

severe accident, and must be carefully avoided.

Never use a CAT I measuring product in CAT II, III, or IV

environments. The measurement categories comply with

the Overvoltage Categories of the IEC60664 Standards.

__________________________________________________

_____________________________________________

DANGER

To prevent electric shock, do not connect the

test terminals to a UTP cable, etc., that is

connected to an operational network. The test

terminals (RJ-45) for this device are specifically

designed for checking standalone UTP cables.

WARNING

To avoid electric shock, do not allow the

product to get wet, and do not use it when your

hands are wet.

Do not connect this device to a UTP cable while

the device is wet. Doing so could result in

electric shock.

Do not use the product where it may be

exposed to corrosive or combustible gases. The

product may be damaged or cause an

explosion.

To avoid a shock hazard, disconnect the UTP

cable before replacing the batteries. Before

using the product after replacing the batteries,

replace the cover and screw.

Do not mix old and new batteries, or different

types of batteries. Also, be careful to observe

battery polarity during installation. Otherwise,

poor performance or damage from battery

leakage could result.

Notes on Use

Follow these precautions to ensure safe

operation and to obtain the full benefits of the

various functions.

__________________________________________________

_____________________________________________

WARNING

To avoid the possibility of explosion, do not

short circuit, disassemble or incinerate

batteries.

Handle and dispose of batteries in accordance

with local regulations.

CAUTION

Do not store or use the product where it could be

exposed to direct sunlight, high temperature or

humidity, or condensation. Under such conditions,

the product may be damaged and insulation may

deteriorate so that it no longer meets specifications.

To avoid damage to the product, protect it from

vibration or shock during transport and handling,

and be especially careful to avoid dropping.

Adjustments and repairs should be made only by

technically qualified personnel.

NOTE The indicator appears when battery voltage

becomes low. Replace the batteries.

Always turn the power switch off after you are

done using the unit.

Do not use any power source other than the

specified batteries (LR6/AA). Using

manganese or other batteries will result in

shorter battery life.

To avoid corrosion from battery leakage,

remove the batteries from the product if it is to

be stored for a long time.

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente