HP Cluster Platform Hardware Kits v2010 Manuale utente
HP BladeSystem c-Class Enclosure Cable
Management Bracket Installation Guide
HP Part Number: 436670-doc
Published: September 2008
©Copyright 2008 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
InfiniBand™ is a trademark of the InfiniBand® Trade Association.
Printed in the U.S.A.
Table of Contents
1 Preparing for Installation................................................................................................7
1.1 Audience...........................................................................................................................................7
1.2 Documentation Resources.................................................................................................................7
1.3 Kit Description..................................................................................................................................7
1.4 Kit Contents.......................................................................................................................................7
1.5 Required Resources...........................................................................................................................8
1.6 Prerequisites......................................................................................................................................9
2 Aligning the Bracket.....................................................................................................11
3 Installing the Cable Management Bracket................................................................13
3.1 Installing the Cable Management Bracket......................................................................................13
3.2 Installing the Releasable Cable Ties for the InfiniBand Cables.......................................................13
4 Removing InfiniBand Cables and Switches...............................................................17
4.1 Removing a Damaged Cable From the c-Class Cable Management Bracket.................................17
4.2 InfiniBand Switch Removal.............................................................................................................17
Table of Contents 3
List of Figures
1-1 Bracket Hardware...........................................................................................................................8
2-1 Bracket Orientation.......................................................................................................................11
2-2 Bracket Mounting Locations.........................................................................................................12
3-1 A Cable Management Bracket Holding 16 InfiniBand Uplink Cables..........................................14
3-2 A Cable Management Bracket Holding 8 InfiniBand Uplink Cables...........................................15
3-3 InfiniBand Cable Secured with a Releasable Cable Tie.................................................................16
3-4 Gauging the Tightness of the Releasable Cable Tie Loop.............................................................16
4-1 Cable Tie Release Tab....................................................................................................................17
4 List of Figures
List of Tables
1-1 Fasteners (Supplied with Cabinet Mounting Hardware)...............................................................8
2-1 Bracket Mount Locations...............................................................................................................12
5
6
1 Preparing for Installation
1.1 Audience
This guide is intended for HP service representatives and other persons trained to install hardware
options in HP 10000 series racks. Such persons are expected to understand the hazards of working
in this environment and to take suitable precautions to minimize danger to themselves and
others.
1.2 Documentation Resources
You can download the documentation for components referenced in this installation guide from
the following locations:
• HP 10000 Series Rack (Documentation option):
http://h18004.www1.hp.com/products/servers/proliantstorage/racks
• HP Cluster Platform:
http://docs.hp.com/en/highperfcomp.html
1.3 Kit Description
The c-Class enclosure cable management bracket described in this manual is designed to align
and support the InfiniBand cables that lead from HP BladeSystem c-Class InfiniBand switches.
For example, the InfiniBand cables that run from an HP BLc 4X DDR InfiniBand switch mounted
in the rear of the HP BladeSystem c-Class enclosure to another switch, or a similar interconnect
device. The kit provides strain relief for the cables connected to the individual InfiniBand
interconnect ports and ensures a good connection. It also ensures the correct bend radius for the
cable and provides channels for cable routing and cable management. One HP BladeSystem
c-Class enclosure cable management bracket is required for each bay of system interconnect
device.
NOTE: The c-Class server blade enclosure cable management bracket is designed to support
24 AWG (0.41 inch) diameter, 26 AWG (0.37 inch) diameter, and 28 AWG (0.33 inch) diameter
QSFP InfiniBand cables. Consult the documentation supplied with your cluster before installing
the brackets and routing the cables.
1.4 Kit Contents
Verify that the cable management bracket kit contains the following components:
• Packaging and documentation.
• The bracket hardware shown in Figure 1-1.
1.1 Audience 7
Figure 1-1 Bracket Hardware
1
2
5
6
3
7
4
The following list describes the callouts in Figure 1-1:
1. HP BladeSystem c-Class Enclosure Cable Management Bracket
2. Completed releasable cable tie assembly
3. First hole (port 1) of the inside row of holes used for the InfiniBand switch with 16
external uplink ports (489183-B21)
4. Push-button mount
5. Rail-mount hook (one on each end of the bracket)
6. Mounting hole to fasten the bracket to the rack's rear rail (one on each end of the bracket)
7. Outside row of holes used for the InfiniBand switch with 8 external uplink ports
(410398-B21)
• The fasteners that are specified in Table 1-1.
Table 1-1 Fasteners (Supplied with Cabinet Mounting Hardware)
DescriptionTorqueFormatSizeQty.
Cage nut for M6 screw.N/ASquare nutM6 cage nuts2
Machine screw. For use with M6 cage nut.25-30 in/lb#2 Cross recessM6 x 0.625 inch
pan head screws
2
To prevent screws from becoming loose because of vibration, HP recommends that you use
an adjustable torque drive, set to the torque specifications given in the table above. Contact
your HP sales representative if any parts are missing.
• 16 push-button mounts (see callout 4 in Figure 1-1)
• 16 releasable cable ties (see callout 2 in Figure 1-1)
Note:
This cable management bracket might also be adaptable for other cable management solutions
(consult your hardware installation documentation).
1.5 Required Resources
To install the HP c-Class enclosure cable management bracket, you require the following resources:
8 Preparing for Installation
• Tools:
— Screwdriver, #2 (medium) Phillips.
— Cage-nut insertion tool (shipped with the rack) or a flat-headed screwdriver.
— Marker pen or masking tape.
• Resources: Cables of the type used by the HP BladeSystem c-Class InfiniBand switch.
1.6 Prerequisites
Before you begin to mount the bracket:
•Follow the usual cable-handling precautions for InfiniBand cables, see the HP Cluster Platform
InfiniBand Interconnect Installation and User's Guide.
•Ensure you know how to plug in the InfiniBand cables, as described in the HP Cluster Platform
InfiniBand Interconnect Installation and User's Guide.
• Read the rack installation instructions for the c-Class enclosure.
• Obtain the set of cabling tables required for your HP Cluster Platform solution.
Important:
Do not secure the enclosure into the rack before you begin the bracket installation. You must be
able to access the rear (inward) face of the rack columns.
1.6 Prerequisites 9
10
Altri manuali per Cluster Platform Hardware Kits v2010
8
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali HP Server
HP
HP ProLiant DL585 Manuale utente
HP
HP D7171A - NetServer - LPr Manuale utente
HP
HP t5740 - Thin Client Manuale utente
HP
HP ML370 - ProLiant - G3 Guida all'installazione
HP
HP ProLiant ML370 G5 Istruzioni utente
HP
HP 9000 A-180 Manuale utente
HP
HP ML150 - ProLiant - G6 Istruzioni per il montaggio
HP
HP ProLiant DL160 Generation 6 Manuale
HP
HP Integrity cx2600 Manuale operativo
HP
HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Istruzioni per il montaggio
HP
HP vc4815 - Thin Client Manuale utente
HP
HP Sa3110 - VPN Server Appliance Manuale utente
HP
HP Cluster Platform Introduction v2010 Manuale utente
HP
HP LC2000r - NetServer - 128 MB RAM Manuale di installazione e funzionamento
HP
HP BladeSystem bc2000 - Blade PC Manuale utente
HP
HP ProLiant ML110 Gen9 Manuale
HP
HP D7171A - NetServer - LPr Manuale utente
HP
HP D7171A - NetServer - LPr Manuale utente
HP
HP ProLiant DL585 G7 Manuale utente
HP
HP ProLiant DL288 GENERATION 6 Manuale utente
