integi M10 Manuale utente
M10 INSTRUCTION MANUAL
INTEGI, S.A.
Autonomia Kalea, 5 - 48250 Zaldibar, Bizkaia – España / +34 943 174 800 - ✉[email protected] / www.integi.com
Page 1
M10 Instruction manual
1. TOOL SPARE PARTS
ITEM
CODE
REFERENCE
DESCRIPTION
ITEMS
INCLUDED
SET.01
01983200
EAM10
Rolling set
P.01+P.02
*P.01
-
EM10
Axis of the knurl
-
*P.02
-
AM10
Washer
-
*P.03
-
MM10 25.10.20
Shank M10 25.10.20
-
MM10 25.10.25
Shank M10 25.20.25
C.01
01995100
EA M5-5
Stud screw DIN 913 M5x6
C.01
C.02
01900060
PE D2-8
Elastic pin DIN 1481 Ø2x8
C.02
C.03
01981400
EA M8-25
Stud screw DIN 913 M8x25
C.03
*This item is not sold individually Table 1
Drawing 1
INTEGI, S.A.
Autonomia Kalea, 5 - 48250 Zaldibar, Bizkaia – España / +34 943 174 800 - ✉[email protected] / www.integi.com
Page 2
M10 Instruction manual
2. FEASIBLE KNURLING TYPE
The M10 form knurling tool is conceived for knurling on pieces with diameters between 8 and 200mm.
The obtained pattern depends on the knurls used knurls used as shown below.
TEETH PATTERN
DESCRIPTION
KNURL TYPE
AXIAL
FEED
RADIAL FEED
RAA
Right
AA Knurl
RBL 30º
30º Left helical
BR30º Knurl
RBL 45º
45º Left helical
BR45º Knurl
RBR 30º
30º Right helical
BL30º Knurl
RBR 45º
45º Right helical
BL45º Knurl
RGE 30º
30º Diamond pattern
male
GV30° Knurl
RGE 45º
45º Diamond pattern
male
GV45° Knurl
RGV 30º
30º Diamond pattern
female
GE30º Knurl
RGV 45º
45º Diamond pattern
female
GE45º Knurl
RKE
90º Diamond pattern
male
KV Knurl
RKV
90º Diamond pattern
male
KE Knurl
Table 2
INTEGI, S.A.
Autonomia Kalea, 5 - 48250 Zaldibar, Bizkaia – España / +34 943 174 800 - ✉[email protected] / www.integi.com
Page 3
M10 Instruction manual
3. SETTING THE TOOL AS RIGHT HAND OR LEFT-HAND
The M10 tool is conceived to work on right or left hand. To change
versions:
Remove the axle and the knurl.
Remove the spacer and its positioning pin.
Place the pin into the hole on the opposite face of the shank.
Place the spacer and re-assembly the knurl and the axle.
4. CLAMPING AND SETTING THE TOOL TO THE MACHINE
First, we need to make sure that the knurl rotates freely around the pin.
Spread graphite grease if necessary.
Clamp the tool to the turret of the lathe.
While the chuck rotates very slowly, approach the tool to the workpiece
until the knurl makes contact with the workpiece.
Approach the knurling wheel to the workpiece following ‘F’ direction up
until the teeth plunge a little into it. Check out the resulted print. The
printed width (h) must be equal to the width of the teeth on the knurl. If
the width isn´t correct, change the clearance angle.
The tool and the workpiece need to be aligned as shown on the drawing
3.
5. KNURLING STEPPED WORKPIECES
When knurling stepped workpieces, it is not possible to knurl up to a shoulder. Using this tool, no knurling
should be performed closer to 0,5mm from the shoulder itself.
6. BEGINNING TO KNURL
While the chuck is rotating at the speed recommended at point 8, feed
the tool so that 1/3 of the width of the knurling wheel gets in contact with
the workpiece.
Press the knurl against the workpiece. The value of the radial feed must
be according to the conditions recommended on the point 9. After that,
you will be able to feed longitudinally.
To calculate up to what diameter we must deepen with the knurl, we must
take into account the height of the tooth (in this case of standard knurls is
always equal to half the step) and the increase in diameter that suffer the
material.
That information is available at www.integi.com and in our catalogue.
Drawing 2
Drawing 3
Drawing 4
INTEGI, S.A.
Autonomia Kalea, 5 - 48250 Zaldibar, Bizkaia – España / +34 943 174 800 - ✉[email protected] / www.integi.com
Page 4
M10 Instruction manual
7. BEFORE AND DURING THE WORKING PROCESS
Make sure that the knurl pins are firmly fastened.
Check that the knurl run free and lubricate it with graphite grease.
Always apply plenty of coolant, lubricant or cutting oil flowing in order to sweep the swarf away.
Always feed against the thickest of the areas that the hold the pin. If a second run is needed,
move the tool away from the workpiece and start again the knurling process. The working
direction, longitudinal advance, will always be against the tool.
8. TROUBLE SHOOTING
PROBLEM
CAUSE
SOLUTION
Double knurling
Too slow radial feed at the
beginning of the knurling
Increase radial feed at the beginning of the
knurling*
The perimeter of the
workpiece is not an exact
multiple of the pitch.
Turn a diameter so that the perimeter to be
knurled is an exact multiple
of the pitch. *
Knurling wheels
easily breakable
Knurling too deep
Reduce the depth to values according to the
pitch
Knurling wheels wear out too
fast
Knurling too deep
Reduce the depth to values according to the
pitch
Working conditions are not
adequate
Check cutting and traverse feeding speeds
9. RECOMMENDED SETTINGS
MATERIAL
ØWORKPIECE
(mm)
ØKNURL (mm)
Cutting
speed
(m/min)
RADIAL feed (mm/rev)
TRAVERSE FEED (mm/rev)
FOR PITCHES (mm)
0.3÷0.6
0.6÷1.2
1.2÷1.6
1.6÷2.0
Acero 600
N/mm2
50÷100
25
30÷60
0.05÷0.10
0.25
0.20
0.15
0.13
100÷200
Acero 900
N/mm2
10÷50
25
25÷50
0.04÷0.08
0.20
0.15
0.10
0.08
50÷100
5
100÷200
Acero
inoxidable
10÷50
25
25÷50
0.04÷0.08
0.20
0.15
0.10
0.08
50÷100
25
100÷200
Acero
fundido
10÷50
25
30÷50
0.05÷0.10
0.25
0.20
0.15
0.13
50÷100
25
100÷200
Aluminio
10÷50
25
35÷60
0.05÷0.10
0.25
0.20
0.15
0.13
50÷100
25
100÷200
Latón
10÷50
25
40÷65
0.05÷0.10
0.30
0.25
0.20
0.18
50÷100
25
100÷200
25
Table 3
* Sometimes, it is not possible to increase radial feed or it just cannot be radially fed if the workpiece is too
weak.
Table 4
www.integi.com
www.integi.com
INTEGI,
S.A.
Autonomía Kalea, 5 - 48250 Zaldibar (Bizkaia)
-
S
pain
www.integi.com
Indice
Altri manuali integi Utensili
